Jamo I/O 8A2 Handleiding

Jamo Speaker I/O 8A2

Lees hieronder de 📖 handleiding in het Nederlandse voor Jamo I/O 8A2 (9 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

Indoor/Outdoor

1A2, 3A2, 3S, 3T, 8A2

Congratulations on your purchase of

Jamo Indoor/Outdoor speakers.

Fig. 1

Congratulations on your purchase of

Jamo Indoor/Outdoor speakers

Package content

Speaker (2) Port plug “i” (4) Allen wrench (1)

Assembled bracket (2) Thumb screw “j” (4) Manual (1)

Screw plug “g” (8) Covers “k” (4)

Bracket

The brackets comes pre-assembled. If disassembling the bracket for paint-ing, re-assemble it

as follow: Place the curved bracket (a) between the wall bracket (b) and wall bracket cover

and tighten with the supplied allen wrench. Insert two ½” allen bolts (e) into each side of wall

bracket and tighten towards curved bracket.

Mounting of bracket

The bracket can be mounted for horizontal or vertical placement of the speaker. Mount the

bracket with four screws (not included) appropriate for the surface the bracket is mounted to

(wood, brick, concrete or other). Take into account the weight of the speaker (specications on

back). A hole (f) in the middle of the bracket allows for running the speaker wire through the

bracket if so desired. Cover the screws with four screw plugs (g) g. 2.

Mounting of port plugs

If the front of the speaker is exposed to rain directly entering the bass reex ports (under the

grill), the ports should be closed to avoid lling the speaker with water. High moisture is not a

problem. Remove the grill (h) from the speaker and insert two port plugs (i) into the bass ports.

Re-install the grill. The speaker will reproduce less bass with the ports closed.

Fig. 1

Connecting speaker wires

Loosen speaker terminals by turning counter clockwise. Strip ½”/12 mm in-sulation o each

wire. Twist strands on each wire to form “solid” wire.

Insert one wire into each terminal and tighten terminal by turning clockwise. Make sure posi-

tive (+) is to red terminal and negative (-) to black terminal for correct phasing.

Adjustment of I/O 3T

This model is for 70V or 100V line installation. This is mainly used in com-mercial installations

with many speakers and requires an amplier with matching transformer outputs. A switch

located next to the terminals al-lows for adjustments of the level of the speaker in 10W, 5W,

2.5W and 1.25W settings. Adjust the switch to the desired level on each speaker.

Mounting of speaker

Place the speaker inside the curved bracket as shown in g. 2 and insert thumb screws (j)

through each end of the curved bracket into the speaker.

Adjust the speaker to the desired angle and tighten the thumb screws.

In-stall the covers (k) over the thumb screws. The curved bracket can be

ad-justed in the wall bracket by loosening the two ½” allen bolts (e) and

re-tighten them after adjustment.

Fig. 2

Painting

The speaker and bracket can be painted. Spray painting is recommended. Paint all parts before

assembling. Remove the grill from the speaker before painting and cover the front bae (l) of

the speaker. Apply many thin coats instead of a few thick coats to avoid the paint running or

clogging the grill holes. Re-install grill after painting.

Product specificaties

Merk:	Jamo
Categorie:	Speaker
Model:	I/O 8A2
Kleur van het product:	Wit
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	- W
Equalizer-instellingen:	Nee
Aanbevolen gebruik:	Universeel
Impedantie:	- Ohm
Geschikt voor buitengebruik:	Ja
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Aantal drivers:	1
Woofer:	Ja
Frequentiebereik:	- Hz
Luidspreker soort:	2-weg
Versterker:	Nee
Diameter woofer:	8 "
Aantal woofer drivers:	1
Tweeter:	Nee
Bedrijfstemperatuur (T-T):	-30 - 70 °C