Indesit DIS 04 Handleiding

Indesit Vaatwasser DIS 04

Lees hieronder de 📖 handleiding in het Nederlandse voor Indesit DIS 04 (12 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 118 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Operating instructions

Contents

Installation, 2-3-4

Positioning and levelling

Connecting the water and electricity supplies

Advice regarding the first wash cycle

Technical data

Electrical connection

Description of the appliance, 5

Overall view

Control panel

Loading the racks, 6

Lower rack

Cutlery basket

Upper rack

Start-up and use, 7

Starting the dishwasher

Measuring out the detergent

Wash options

Wash cycles, 8

Table of wash cycles

Rinse aid and refined salt, 9

Measuring out the rinse aid

Measuring out the refined salt

Care and maintenance, 10

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended

periods

Precautions and advice, 11

General safety

Disposal

Saving energy and respecting the environment

Troubleshooting, 12

English, 1

DIS 04

DISHWASHER

Installation

Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given away or

moved, please ensure the manual is kept with the

machine, so that the new owner may benefit from the

advice contained within it.

Please read this instruction manual carefully: it

contains important information regarding the safe

installation, use and maintenance of the appliance.

If the appliance must be moved at any time, keep it in

an upright position; if absolutely necessary, it may be

tilted onto its back.

Positioning and levelling

1. Remove the appliance from all packaging and check

that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or

back panel are in contact with the adjacent cabinets or

even with the wall. This appliance can also be recessed

under a single worktop* (see the Assembly instruction

sheet).

3. Position the dishwasher on a level and sturdy floor. If

the floor is uneven, the front feet of the appliance may be

adjusted until it reaches a horizontal position. If the

appliance is levelled correctly, it will be more stable and

much less likely to move or cause vibrations and noise

while it is operating.

4. Adjust the height of the rear foot from the front of the

appliance* on the central lower part of the dishwasher,

turning a hexagonal spanner (red color) with an opening

of 8 mm in a clockwise direction to increase the height

or in an anticlockwise direction to decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies

should only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water

supply network using new hoses.

Do not use old hoses.

The water inlet (A) and outlet (B) hoses and the

electricity supply cable may be positioned towards the

right or the left in order to achieve the best possible

installation (see figure).

Connecting the water inlet hose

 To a suitable cold water connection point: before

attaching the hose, run the water until it is perfectly

clear so that any impurities that may be present in the

water do not clog the appliance; after performing this

operation, screw the inlet hose tightly onto a tap with

a ¾ gas threaded connection.

 To a suitable hot water connection point: your

dishwasher may be supplied with hot water from the

mains supply (if you have a central heating system

with radiators) provided that it does not exceed a

temperature of 60°C.

Screw the hose to the tap as described for connection

to a cold water supply.

If the inlet hose is not long enough, contact a

specialist store or an authorised technician (see

Assistance).

The water pressure must be within the values

indicated in the Technical data table (see adjacent

information).

The hose should not be bent or compressed.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the

water supply in the event of anomalies or leaks from

inside the appliance.

Some models are also equipped with the supplementary

safety device New Acqua Stop*, which guarantees anti-

flooding protection even in the event of a supply hose

rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be

cut as it contains live electrical parts.

* Only available in selected models.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain

duct with a minimum diameter of 4 cm. Alternatively, rest

it over a sink or tub; the free end of the hose should not

remain immersed in water.

The special plastic elbow*

makes it easier to find the

best layout: fix the elbow to

the wall securely in order

to prevent the outlet hose

from moving and spilling

the dirty water.

The part of the hose

marked with the letter A

should be between 40 and

100 cm above the ground

(see figure).

We advise against the use of hose extensions.

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

 The socket is earthed and complies with current

regulations.

 The socket can withstand the maximum load of the

appliance, which is indicated on the data plate

located on the inside of the door (see chapter entitled

Description of the appliance).

 The power supply voltage falls within the values

indicated on the data plate on the inside of the door.

 The socket is compatible with the plug of the

appliance. If this is not the case, ask an authorised

technician to replace the plug (see Assistance); do

not use extension cables or multiple sockets.

Once the appliance has been installed, the power

supply cable and the electrical socket should be easily

accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be re-

placed by the manufacturer or its Technical Assistance

Service in order to prevent all potential hazards. (See As-

sistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not

observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick

the adhesive transparent strip under the wooden shelf in

order to protect it from any condensation which may

form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately

before running the first wash cycle, completely fill the

salt dispenser with water and add only then

approximately 1 kg of salt (see chapter entitled Rinse aid

and refined salt). The water may overflow: this is normal

and is not a cause for concern. Select the water

hardness value (see chapter entitled Rinse aid and

refined salt). - After the salt has been poured into the

machine, the LOW SALT indicator light* switches off.

If the salt container is not filled, the water softener

and the heating element may be damaged as a result.

* Only available in selected models.

Technical data

Dimensions

width 44.5 cm

height 82 cm

depth 57 cm

Capacity 10 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply

voltage See appliance data plate

Total absorbed

power See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to

the following European

Community Directives:

-2006/95/EEC dated

16/01/2007

(Low Voltage) and subsequent

modifications

-89/336/EEC dated 03/05/89

(Electromagnetic Compatibility)

and subsequent modifications

-97/17/EC (Labelling)

-2002/96/ CE (Waste Electrical

and Electronic Equipment

WEEE)

Product specificaties

Merk:	Indesit
Categorie:	Vaatwasser
Model:	DIS 04
Apparaatplaatsing:	Volledig ingebouwd
Breedte:	445 mm
Diepte:	550 mm
Hoogte:	820 mm
Aantal couverts:	10 couverts
Deurkleur:	Niet van toepassing
Droogklasse:	B
Geluidsniveau:	54 dB
Energie-efficiëntieklasse (oud):	A
Waterconsumptie per cyclus:	10 l
Wasklasse:	A
Aantal wasprogramma's:	4
Kleur bedieningspaneel:	Roestvrijstaal
Verborgen verwarmingselement:	Ja
Energieverbruik per cyclus:	1.01 kWu