Imou Bullet Lite 4MP Handleiding

Imou Bewakingscamera Bullet Lite 4MP

Lees hieronder de 📖 handleiding in het Nederlandse voor Imou Bullet Lite 4MP (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Installing Camera

Make sure the mounting surface is strong enough to hold at least

three times of the device weight.

Step1 Drill screw holes on the mounting surface as the positioning

map shows, and then put in the expansion bolts.

Step2 Attach the camera pedestal to the mounting surface with the

self-tapping screws.

Step3 Power up the camera, and then adjust the lens to the ideal

angle.

Step 5

Step 4

Connect your smart phone to your Wi-Fi network, and make sure your

smartphone is connected to Wi-Fi network with 2.4 GHz band, and then

do the following operations to finish adding camera.

Wait for booting to be finished, and then the camera indicator flashes

with green light.

Note:

If the Wi-Fi network has changed or the indicator status goes

wrong, reset the camera, and then do step 5 to add it again.

If you have more than one camera, do step 5 to add them one

by one.

Mounting SurfaceExpansion Bolt

Self-tapping Screw

Camera Positionting Map

This quick start guide is for reference only. Minor difference might

be found in user interface.

All the design and software here are subject to change without

prior written notice.

All trademarks and registered trademarks mentioned are the

properties of their respective owners.

Please visit our website or contact your local service engineer for

more information.

If there is any uncertainty or controversy, please refer to our final

explanation.

About the Guide

Q: Cannot connect the camera to Internet with Imou App?

Q: The camera failed to boot up, or cannot operate normally?

FAQ

Make sure the camera and your smartphone are connected

to the Internet successfully. If still cannot work, please press

and hold the reset button for 10s to reset the camera, then try

again.

Press and hold the reset button for 10s to reset the camera

and try again.

If still cannot work, please connect the camera to Wi-Fi

network on web page, then add your camera to Imou

account.

Connect the camera to the PC with Ethernet cable,

and set the PC IP to be the same network segment of

camera which is 192.168.1.108 by default, then login to

the web configuration page.

Select Setting > Network > Wi-Fi > Wi-Fi, you will see all

Wi-Fi signal around listed. Double-click your Wi-Fi

name , enter the Wi-Fi password, and then click

Connection.

After camera is connected to Internet, unplug the

Ethernet cable, and then follow the instruction of part

“Operate with Imou App” to try again.

Q: Can I continue recording when the SD Card is full?

Q: Camera is offline?

Please check the LED indicator status:

If the green light is solid on, check whether your Wi-Fi router

is successfully connected to Internet. If Internet is OK, please

reboot your camera, or reset the camera to factory default

and configure again.

If the red light flashes slowly or solid on, reset the camera to

factory default and configure again.

If still cannot work, we suggest you contacting the aftersales

service.

When the storage is full, the camera will overwrite the oldest

existing records. We suggest you storing your important

recordings regularly.

With Imou AppOperating

Step 1

Step 3

Connect the camera to power source with the power adapter.

Scan the following QR code or search “Imou” in Google Play or App

Store to download and install Imou App.

Introduction

Note: Press and hold the

reset

button for 10 s to reset the camera.

Camera

Run Imou App, and then register an account for first use.

Step 2

The pattern of the LED indicator is included in the following table.

LED Indicator Status

Green light flashing

Green light on

Red light flashing

Green and Red light

flashing alternately

Powered off/LED turned off

Rebooting after reset

Booting

Device malfunction

Waiting for network

Operating properly

Network connection failed

Off

Red light on

Firmware updating

QSG ×1

Camera ×1

Positioning Map ×1

Waterproof Connector ×1

Lens

Wi-Fi Antenna

Power Adapter ×1 Screw Package×1

Version 1.0.1

Quick Start Guide

SD Card Slot

Reset Button

LED Indicator

Built-in Mic

1.2.51.32.14760-000

Product specificaties

Merk:	Imou
Categorie:	Bewakingscamera
Model:	Bullet Lite 4MP
Kleur van het product:	Black, White
Gewicht:	260 g
Breedte:	84.6 mm
Diepte:	164.6 mm
Hoogte:	70 mm
Soort:	IP-beveiligingscamera
Gebruikershandleiding:	Ja
Materiaal behuizing:	Metal, Plastic
Internationale veiligheidscode (IP):	IP67
Bluetooth:	Nee
Maximale capaciteit van de geheugenkaart:	128 GB
Wi-Fi-standaarden:	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Vormfactor:	Rond
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad en draadloos
Ethernet LAN:	Ja
Montagewijze:	Plafond/muur
Maximum resolutie:	2560 x 1440 Pixels
Totaal aantal megapixels:	4 MP
Videocompressieformaten:	H.264, H.265
Type stroombron:	DC
Minimale belichting:	- Lux
Aantal cameras:	1
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	MicroSD (TransFlash)
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
Zoomcapaciteit:	Ja
Certificering:	CE, FCC, UL
Omvang optische sensor:	1/3 "
Type beeldsensor:	CMOS
Digitale zoom:	16 x
Ingebouwde microfoon:	Ja
Maximaal 30 frames per seconde:	20 fps
Reset button:	Ja
Ethernet interface type:	Fast Ethernet
Inclusief schroeven:	Ja
Aantal lenzen:	2
Controle camerapanning:	Nee
Kantelfunctie camera:	Nee
Aantal sensoren:	1
Bewegingssensor:	Ja
Nachtkijker afstand:	30 m
Wifi:	Ja
Stroomverbruik (typisch):	4.8 W
Bedrijfstemperatuur (T-T):	-30 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Lens diameter:	3.6 mm