Ilve X400/150 Handleiding

Ilve Afzuigkap X400/150

Lees hieronder de 📖 handleiding in het Nederlandse voor Ilve X400/150 (8 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

X400/80

X400/90

XR400/90

X400/100

X400/120

X400/150

230Vac - 50Hz

Exhausting cooker hood. The equipment is constructed in

accordance with European Standards and with the requirements

included in the following Directives: 2006/95EC ( Low Voltage

Directive), 2004/108 (Electromagnetic Compatibility).

1 INSTALLATION

Read the instruction manual before installing and/or using the

hood .

In order that the minimum distance between the supporting

surface for the cooking pots on gas hob and low-voltage

components present in the hood is at least 65cm as required by

the regulations in force, it is necessary that the lower part of the

hood is at least 65-70cm away from the work top.

If the mounting instructions of the gas cooker indicate a wider

distance, respect it. The unit must not be mounted above cookers

tted with top radiant plate.

Respect all the air discharge regulations.

The air must not be discharged in a pipe used to discharge

exhaust fumes produced by gas- fed equipments or fuel-fed

equipments (this does not apply to ltering hoods).

The room must be adequately ventilated when the hoods is used

together with other gas-fed or fuel-fed equipments.

The hood is equipped with all the necessary fastenings for its

installation, which are suitable for most surfaces. Anyway, ask

to a professional to verify that the installation surface is strong

enough. Installation must be carried out by qualied installers

according to present regulations.

For an easy access, it is advisable to move possible furniture

under the installation area.

Two different wall-mounting systems are used, depending on the

model (Fig. 1-2)

A) Hanging and levelling brackets.

B) Locking screws.

C) Hood/chimney fastening screws (if provided)

D) Chimney/wall bracket and fastening screws.

2 ELECTRICAL CONNECTIONS

This appliance must be connected to an earthed power supply.

Two types of electrical connection can be used:

1. Using a standard plug to be connected to the power cable

and inserted in a mains socket which must be accessible (so

that the plug can be disconnected when servicing is carried

out). Make sure that the plug is accessible also after the

complete installation of the equipment.

2. By means of a xed mains connection, tting a bipolar

switch, which ensures the disconnection, with an opening

distance of the contacts allowing a complete disconnection

on the conditions of the overvoltage III category, according

to installation regulations. The ground connection (yellow-

green wire) must not be interrupted.

Refer to the plate inside the hood for the mains voltage and

frequency ratings.

3 USE

This cooker hood can be employed as exhausting or ltering.

Exhausting (Fig. 3). The carbon lters should not be installed on

the hood in exhausting version.

Kitchen smokes are driven outside through a ue joined to the

exhaust pipe ue connector.

Pipes must be communicating with the exterior of the house. The

diameter of the outlet of the hood is 150mm. A 150-125 reduction

is provided with the hood.

This pipe must not under any circumstances be connected to

cooker, boiler or burner exhaust pipes, etc.

Filtering (Fig. 4). The fumes pass through the carbon lters to be

puried and recycled into the kitchen through a pipe connected

to the outlet of the hood up to the hole in the top of the cabinet.

This hole must be free and communicating with the kitchen.

In the ltering version you must install the two carbon lters on

the sides of the aspirator. To install the carbon lters you must

rst remove the metal grease lters (Fig. 5) and then install

carbon lters by turning them counterclockwise (Fig. 6).

4 OPERATION

The hood is equipped with a multispeed motor.

It is recommended that low speed be selected for normal kitchen

conditions, and higher speeds only to combat a heavy build-up

odours and vapours.

ELECTRONIC CONTROLS

The controls (Fig. 7) have buttons for switching on the TL light, for

switching on the motor and selecting the T1-T2-T3-T4 operating

speed.

By pressing of the command T1 the motor starts running at

the 1st speed. The commands T2-T3-T4 switch the motor on

respectively at the 2nd, 3rd, 4th speed. In order to switch

the motor off press T1 once if set at the 1st speed, twice if set at

the 2nd, 3rd and 4th speed.

With the button T4, select the maximum speed of the extraction

fan for 5 minutes (LED blinking), after which the extraction fan

will automatically switch to the 3rd speed.

AUTO POWER OFF: To activate the auto power off, rst turn on

the hood and, then, push the “T1” button for a few seconds until

all LEDs start ashing. By pressing one of the buttons (T1, T2,

T3, T4) it is possible to program the auto power off time, which

will be different according to the button

pressed (T1= 5 minutes, T2=10 minutes, T3=15 minutes, T4=20

minutes). The set speed can be changed during the auto power

off time. When the auto power off option corresponds to the

previously set speed, the speed LED ashes; if the option is

different, the speed LED is xed.

FILTER TIMER: After the hood has worked for 30 hours, all

LEDS will switch on with a xed light for 30 seconds when the

hood is turned off indicating that the aluminium lters need to be

cleaned. The timer will reset if the T1+T4 button is pressed for a

few seconds with the exhaust fan turned off. If this button is not

pressed, the same operation will occur again once the hood is

switched off again. This operation will occur every 30 hours, until

120 functioning hours are reached. Once the hood has worked

for 120 hours and it is turned off, all the LEDs will turn on with

a ashing light for the following 30 seconds indicating the that

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS FOR COOKER HOODS

FOR WALL FITTING 230 Vac - 50 Hz

0-1 2 3 4

TL T1 T2 T3 T4

FIG.7

Product specificaties

Merk:	Ilve
Categorie:	Afzuigkap
Model:	X400/150

Heb je hulp nodig?

Als je hulp nodig hebt met Ilve X400/150 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Afzuigkap Ilve

Ilve AGK90 Handleiding

20 November 2024

Ilve AGQ90 Handleiding

20 November 2024

Ilve AGQ60 Handleiding

20 November 2024

Ilve AGQ120 Handleiding

20 November 2024

Ilve AGK120 Handleiding

20 November 2024

Ilve AGQ150 Handleiding

20 November 2024

Ilve ANB90AWC Handleiding

5 Mei 2024

Ilve ANB150WHC Handleiding

3 Mei 2024

Ilve X370 Handleiding

28 Maart 2024

Ilve IVG901X1 Handleiding

18 Maart 2024

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap

Haier UVW7241SNSS Handleiding

30 December 2025

Kluge KOV5002BLG Handleiding

27 December 2024

MPM -61-PX-75 Handleiding

24 December 2024

MPM -61-PX-76 Handleiding

24 December 2024

MPM -61-PX-77 Handleiding

24 December 2024

Kaiser A 9315 ElfEm Eco Handleiding

20 December 2024

Kaiser A 9315 RotEm Eco Handleiding

20 December 2024

Kaiser AT 9343 Handleiding

20 December 2024

Kaiser A 6315 RotEm Eco Handleiding

20 December 2024

Kaiser AT 6445 AD Eco Handleiding

20 December 2024