Hunter Outdoor Original 25602 Handleiding

Hunter Ventilator Outdoor Original 25602

Lees hieronder de 📖 handleiding in het Nederlandse voor Hunter Outdoor Original 25602 (8 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
1
41556-01 8/08/03 © 2003 HUNTER F A N CO.
S I N C E 1 8 8
6
®
INSTALLATION INSTRUCTIONS FOR
HUNTER ORIGINAL® CEILING FANS
!
WARNINGS
!
• To avoid possible electrical shock, before wir-
ing fan, disconnect power by turning off the cir-
cuit breakers both to the outlet box and to its
associated wall switch location. If you cannot
lock the circuit breakers in the “OFF” position,
securely fasten a prominent warning device,
such as a tag, to the service panel.
• All wiring must be in accordance with national
and local electrical codes. If you are unfamiliar
with wiring, you should use a qualified electri-
cian.
• To reduce the risk of personal injury, install the
fan to the building structure according to these
instructions and use only the hardware sup-
plied.
IMPORTANT!
READ AND SAVE THESE
INSTRUCTIONS!
!
CAUTIONS
!
• NEVER REST THE FAN ON THE SWITCH HOUS-
ING. As you prepare the fan for installation, rest
the motor in the liner in which it was packed.
• Be sure to put full contents of the oil tube into
the fan according to the instructions.
• If this fan is used as a replacement for an Origi-
nal® Old-Tyme non-reversible fan, it must be in-
stalled per the instructions included with this
fan. Failure to do so could result in the fan fall-
ing. DO NOT HANG THIS FAN ON A SINGLE
“J” HOOK.
• To reduce the risk of noise and to ensure proper
fan operation, do not use a solid-state speed
control with this fan. Use Hunter speed con-
trols for Hunter Original® ceiling fans only.
• Do not use an abrasive cleaner on the fan. A
mild detergent will clean and restore most units
to their original beauty.
Installing Your Hunter® Ceiling
Fan
Note To Installers: Please leave this manual with
the home owner.
Tools needed:
• Pliers • 3/8” Socket Wrench
• Flat blade screwdriver • Phillips screwdriver
• Electric drill • 11/64” drill bit
• 4” x 1-1/2” standard octagon electrical box
Step 1: Pre-Installation
1. Select the installation site: Normally this is
near the center of the room, often replacing a light
fixture. Make certain that ample clearance is left
for the rotating fan blades. For maximum effi-
ciency, no obstructions (walls, posts, etc.) should be
within 24” of the tips of the blades. See Figure 1.
NOTE: Mounting should also meet the precautions listed
in Step 3.
Read this entire manual thoroughly before begin-
ning installation.
24”
Minimum
Clearance
7’ Minimum
Clearance To
Floor
8’Minimum
to Ceiling
Figure 1
2. Fan mounting height: Your Hunter fan
comes with the proper hardware to hang the fan
from a standard 8 foot ceiling so that the fan blades
will be 12” from the ceiling and approximately 7
feet from the floor. See Figure 1.
NOTE: On vaulted ceilings, up to 45° pitch, you must
use the Hunter Vaulted Ceiling Mounting Kit.
© 2 0 03 HU NTER F A N CO. 41556-0 1 8/08/0 3
2
Step 2: Inspect the Fan
1. Unpack the fan carefully to avoid any damage to components.
Figure 2
!
CAUTION
!
• Never lift the motor by the wires. Let the motor rest in the carton liner for protection.
2. Check the sack parts. See Figure 2.
Blade Assembly
Screw
Armature Screw
Pull Chain
1/4-10 Lag Screw
Mounting Bracket
Pipe Nipple
Oil Tube
Motor / Housing Assembly
Blade Set
Blade Iron Set
Hardware
(Drawn to Scale)
Fan Parts
(Not Drawn to Scale)
Canopy
Rubber Bushing / Pin
Hanger Bracket
Assembly
Canopy
Insert
Wire Nut
Canopy Screw
Mounting Isolator
3
41556-0 1 8/0 8 / 0 3 © 2 0 03 HU NTER F A N CO.
Step 3: Installation of Ceiling Mounting
Hardware
2” x 4” Wood Brace
Outlet Box
Ceiling
Joist
Ceiling
M4 Wood Screw &
Washer (2) Required
Figure 3
2. Drill two (2) 1/4” diameter holes 2-9/16”
apart through the back of the outlet box into the
cross brace. There may be two holes at the correct
spacing, but they will probably have to be enlarged.
3. Use the two (2) bracket screws to secure the
hanger bracket and canopy plate to the joist as
shown in Figure 4. Install the rubber bumpers into
the canopy plate and the rubber bushing in the
hanger bracket before assembling the parts to the
ceiling joist.
Rubber
Bumpers
Figure 4
Step 4: Hanging the Fan
• When inspecting or preparing the installation
site where wiring is available, to avoid possible
electrical shock, disconnect power by turning off the
circuit breakers both to the outlet box and to its
associated wall switch location. If you cannot lock
the circuit breakers in the off position, securely
fasten a prominent warning device, such as a tag, to
the service panel.
• All wiring must be in accordance with na-
tional and local electrical codes. If you are unfamil-
iar with wiring, you should use a qualified electri-
cian.
• Do not mount directly to an unsupported
ceiling or to an electrical outlet box.
• The wood joist chosen for mounting the fan
must be sound and of sufficient size. In no case
should it be smaller than standard 2”x4” lumber.
1. Secure a metallic outlet box 4” x 1-1/2” or
4” x 1/2” deep to a 2” x 4” cross brace between two
ceiling joists as shown in Figure 3. The outletbox
must be recessed in the ceiling by 1/16” minimum.
Secure the outlet box to the cross brace by drilling
two (2) pilot holes no larger than the minor diameter
of the woodscrews (5/64”) and use two #8 x 1-1/2”
woodscrews and washers. Use the innermost holes
for securing the box. Orient the box so the outer-
most holes are aligned with the 2” x 4” brace. The
outermost holes will be use in Step 3 sub-step 2.
!
CAUTION
!
• Your Hunter ceiling fan weighs up to 50 lbs. The
following precautions must be taken for safety,
and to ensure that your fan is securely mounted
to the ceiling.
!
CAUTION
!
• Do not use a lubricant on the screws.
!
CAUTION
!
• Do not use a lubricant on the screws.
!
CAUTIONS
!
• Be sure to tighten the pipe nipple shown in Fig-
ure 2 into the fan, tighten the hanger bracket
onto the pipe, and tighten the two set screws
as described in sub-step 2 to prevent the fan
from falling.
• Your fan may weigh up to 50 lbs. All of the fol-
lowing steps must be followed in order to en-
sure a secure mounting. Perform sub-steps 1-
4 with the motor resting in the liner for protec-
tion.
1. Take the hanger bracket from the sack parts
and locate the pipe nipple (See Figure 2.). Feed the
wires from the top of your motor through the pipe.
2. Back out the set screw in the neck of the
motor housing and the hanger bracket so the pipe
can be screwed in. Screw the pipe into the fan until
tight (at least 4-1/2 turns). Feed the wire through
the canopy and the canopy insert and let the canopy
rest on the neck of the motor. Slide the canopy
insert over the pipe.Feed the wire through the
hanger bracket and screw the hanger bracket onto
the pipe until tight (at least 3 turns). Then use pliers
to tighten both the hanger bracket and the pipe
together. Tighten the set screw in the motor housing
with pliers. Securely tighten the set screw in the
hanger bracket. See Figure 5.

Product specificaties

Merk: Hunter
Categorie: Ventilator
Model: Outdoor Original 25602

Heb je hulp nodig?

Als je hulp nodig hebt met Hunter Outdoor Original 25602 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Ventilator Hunter

Hunter

Hunter Anslee 59269 Handleiding

16 November 2024
Hunter

Hunter Bennett Handleiding

11 November 2024
Hunter

Hunter Gravity Handleiding

11 November 2024
Hunter

Hunter Minimus Handleiding

11 November 2024
Hunter

Hunter Neuron Handleiding

11 November 2024
Hunter

Hunter Phenomenon Handleiding

11 November 2024
Hunter

Hunter Rogers Handleiding

11 November 2024
Hunter

Hunter Rhinebeck Handleiding

11 November 2024
Hunter

Hunter Hardwick Handleiding

11 November 2024
Hunter

Hunter Swanson Handleiding

11 November 2024

Handleiding Ventilator

Nieuwste handleidingen voor Ventilator

Svan

Svan SVP401600MOBA Handleiding

20 December 2024
Svan

Svan SVP401600OBA Handleiding

20 December 2024
Livoo

Livoo DOM510 Handleiding

20 December 2024
Orava

Orava SF-13 Handleiding

18 December 2024
EMOS

EMOS P56PR2 Handleiding

14 December 2024
Midea

Midea FTS30-13AR Handleiding

14 December 2024
Midea

Midea FTS35-9AR Handleiding

14 December 2024
Midea

Midea FTS30-9AR Handleiding

14 December 2024
Aspes

Aspes AVT453100ON Handleiding

13 December 2024
Aspes

Aspes AVP401600OVBA Handleiding

13 December 2024