Hotpoint WMBF 742P UK.M Handleiding

Hotpoint Wasmachine WMBF 742P UK.M

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint WMBF 742P UK.M (16 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

English,1

WASHING MACHINE

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 6

Cutting off the water and electricity supplies

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Disposal

Description of the washing machine, 8-9

Control panel

Display

Running a wash cycle, 10

Wash cycles and options, 11

Table of programmes and wash cycles

Wash options

Detergents and laundry, 12

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Troubleshooting, 13-14

Product Guarantee and Repair Information, 15

WMBF 742

Instructions for use

Installation

2. If the floor is not perfectly level, compensate

for any unevenness by tightening or loosening

the adjustable front feet the angle (see figure);

of inclination, measured according to the

worktop, must not exceed 2°.

Levelling your appliance correctly will provide

it with stability and avoid any vibrations, noise

and shifting during operation. If it is placed on

a fitted or loose carpet, adjust the feet in such

a way as to allow enough room for ventilation

beneath the washing machine.

Electric and water connections

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tap using

a 3/4 gas threaded

connection (see

figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other

end of the water inlet

hose to the washing

machine,

screwing it onto the

appliance’s cold water

inlet, situated on the

top right-hand side

on the rear of the

appliance (see figure).

3. Make sure there are no kinks or bends in the

hose.

! The water pressure at the tap must be within

the values indicated in the Technical details

table (on the page 5).

! If the water inlet hose is not long enough,

contact a specialist store or an authorised

serviceman.

! Ensure that the supply taps are allowing

water through. Old taps may seize in the

closed position and thus prevent water

reaching the machine.

! Never use second-hand or old inlet hoses;

use the products supplied with the machine.

! Keep this instruction manual in a safe place

for future reference. Should the appliance be

sold, transferred or moved, make sure the

instruction manual accompanies the washing

machine to inform the new owner as to its

operation and features.

! Read these instructions carefully: they contain

vital information on installation, use and safety.

Unpacking and levelling

Unpacking

! This is a separate

part of the polystyrene

base and should be

removed with the

base.

! IMPORTANT check

when unpacking

your machine.

1. Unpack the washing

machine.

2. Check whether the

washing machine has

been damaged during

transport. If this is the

case, do not install

it and contact your

retailer.

3. Remove the 3

protective screws and the rubber bush with

the respective spacer, situated on the rear of

the appliance (see also the installation leaflet).

4. Seal the gaps using the plastic plugs

provided.

5. Keep all the parts: you will need them again

if the washing machine needs to be moved to

another location.

! Packaging materials are not children’s toys.

Levelling

Your machine may

make a considerable

amount of noise if the

two front feet have

not been adjusted

correctly.

1. Install the washing

machine on a flat sturdy

floor, without resting it up

against walls, cabinets

or anything else.

Connecting the drain hose

Connect the drain

hose, without bending

it, to a draining

duct or a wall drain

situated between 65

and 100 cm from the

floor;

The drain hose may

be connected to

an under-sink trap.

Before connecting

the drain hose from

the machine ensure

that any blanks or

removable ends have

been taken off the

spigot.

If it is placed over

the edge of a basin

or sink be sure

the free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

in case of absolute need, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into

a standpipe, that the end does not go down

more than 15cms (6 inches). If the hose is

pushed down too far, this may cause the

machine to self -syphon ie. continuously empty

as it is filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the

Technical Data Plate fixed on the machine;

• the supply voltage is included within the

values indicated on the Technical Data Plate

fixed on the machine.

• the socket is compatible with the washing

machine’s plug. If this is not the case,

replace the socket or the plug.

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the

appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD

BE CARRIED OUT BY A QUALIFIED

ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must

be of the correct colour as indicated by

the coloured marking or the colour that is

embossed in words on the base of the plug.

Replacements can be obtained directly from

your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable

moulded plug and you should wish to re-route

the mains cable through partitions, units etc.,

please ensure that either:

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of

approval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot

be accidentally inserted into a socket.

Instructions for connecting cable to an alternative

plug:

Important: the wires in the mains lead are

coloured in accordance with the following

code:

Green & Yellow Earth

Blue Neutral

Brown Live

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

As the colours of the wires in the lead may

not correspond with the coloured markings

identifying the terminals in your plug, proceed

as follows:

Connect Green & Yellow wire to terminal

marked or or coloured Green or Green & E

Yellow.

Connect Brown wire to terminal marked or L

coloured Red.

Connect Blue wire to terminal marked or N

coloured Black.

If a 13 amp plug (BS 1363) is used it must be

fitted with a

13 amp fuse, either in the plug or adaptor or

at the distribution board.

If you are in any doubt regarding the electrical

supply to your machine, consult a qualified

electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please

remove the plug by cutting the mains cable

as close as possible to the plug body and

dispose of it as described on the previous

page.

! The washing machine should not be installed

in an outdoor environment, not even where

the area is sheltered, because it may be very

dangerous to leave it exposed to damp, rain

and thunderstorms.

! When the washing machine is installed, the

mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

! The power supply cable must only be

replaced by an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

programme “Auto Clean” (see “Cleaning the

washing machine”).

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Technical data

Model WMBF 742

Dimensions

width 59.5 cm

height 85 cm

depth 52.2 cm

Capacity from 1 to 7 kg

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water con-

nections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 46 litres

Spin speed up to 1400 rotations per minute

Test wash

cycles in

accordance

with re-

gulations

1061/2010

and

1015/201

Programme 9;

Eco Cotton 60°.

Programme 9;

Eco Cotton 40

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU (WEEE)

Care and maintenance

Cutting off the water and

electricity supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system

inside the washing machine and help to

prevent leaks.

• Unplug the washing machine when cleaning

it and during all maintenance work.

Cleaning the washing machine

• The outer parts and rubber components

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

• The washing machine has a “Auto Clean”

programme for its internal parts that must be

run with no load in the drum.

To help the wash cycle

you may want to use

either the detergent

(i.e. a quantity 10%

the quantity specified

for lightly-soiled

garments) or special

additives to clean the

washing machine. We

recommend running a

cleaning programme every 40 wash cycles.

To start the programme press button for 5 A

seconds (see figure).

The programme will start automatically and will

run for about 70 minutes. To stop the cycle

press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and

pulling it out (see

figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such as

coins or buttons) may fall into the pre-chamber

which protects the pump, situated in its bottom

part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. using a

screwdriver, remove

the cover panel on

the lower front part of

the washing machine

(see figure);

2. unscrew the lid

by rotating it anti-

clockwise : (see figure)

a little water may

trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Precautions and tips

! This washing machine was designed and constructed

in accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU - WEEE on Waste

Electrical and Electronic Equipment, requires that old

household electrical appliances must not be disposed of in

the normal unsorted municipal waste stream. Old appliances

must be collected separately in order to optimise the recovery

and recycling of the materials they contain and reduce the

impact on human health and the environment. The crossed

out “wheeled bin” symbol on the product reminds you of

your obligation, that when you dispose of the appliance it

must be separately collected. Consumers should contact

their local authority or retailer for information concerning the

correct disposal of their old appliance.

Description of the washing

machine

Control panel

TEMPERATURE

button

WASH

CYCLE

SELECTOR

KNOB

Detergent dispenser drawer

ON/OFF

button

SPIN

button

START/PAUSE

button and indicator

light

DISPLAY

DELAY

button

OPTION

button and

indicator light

CLEANING

ACTION

button

KEY

LOCK

button

Detergent dispenser drawer: used to dispense

detergents and washing additives ( see “Detergents and

laundry”).

ON/OFF button: press this briefly to switch the

machine on or off. The START/PAUSE indicator light which

flashes slowly in a green colour shows that the machine is

switched on. To switch off the washing machine during the

wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the

machine will not switch off.

If the machine is switched off during a wash cycle, this

wash cycle will be cancelled.

WASH CYCLE SELECTOR KNOB: used to set the

desired wash cycle (see “Table of programmes and wash

cycles”).

OPTION button and indicator light: press to select the

available options. The indicator light corresponding to the

selected option will remain lit.

CLEANING ACTION

button to select the desired :

wash intensity.

TEMPERATURE button: press to reduce or completely

exclude the temperature; the value appears on the display.

SPIN button: press to reduce or completely exclude

the spin cycle; the value appears on the display.

DELAY button: press to set a delayed start for the

selected wash cycle; the delay period appears on the

display.

START/PAUSE button and indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the indicator

light will remain lit in a fixed manner. To pause the wash

cycle, press the button again; the indicator light will flash

in an amber colour. If the symbol is not illuminated,

the door may be opened (wait approximately 3 minutes).

To start the wash cycle from the point at which it was

interrupted, press the button again.

KEY LOCK button: to activate the control panel lock,

press and hold the button for approximately 2 seconds.

When the indicator light is illuminated, the control

panel is locked (apart from the ON/OFF button). This

means it is possible to prevent wash cycles from being

modified accidentally, especially where there are children in

the home. To deactivate the control panel lock, press and

hold the button for approximately 2 seconds.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF button briefly and

wait for the machine to start up again.

Display

The display is useful when programming the machine and provides a great deal of information.

The duration of the available wash cycles and the remaining time of a running cycle appear (the display will show the

maximum duration of the cycle chosen, which may decrease after several minutes, since the effective duration of the

programme varies depending on the wash load and the settings chosen); if the DELAY option has been set, the countdown

to the start of the selected wash cycle will appear.

Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the

machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.

DOOR LOCKED indicator light:

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door (wait approximately 3 minutes).

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened (wait approximately 3 minutes).

Running a wash cycle

1. Press the button; SWITCH THE MACHINE ON.

the START/PAUSE indicator light will flash slowly in a

green colour.

2. Open the porthole door. LOAD THE LAUNDRY.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

3. Pull out the MEASURE OUT THE DETERGENT.

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. Use the WASH CYCLE SELECT THE WASH CYCLE.

SELECTOR knob to select the desired wash cycle. A

temperature and spin speed is set for each wash cycle;

these values may be adjusted. The duration of the cycle

will appear on the display.

6. Use the relevant CUSTOMISE THE WASH CYCLE.

buttons:

Modify the temperature and/or spin speed.

The machine automatically displays the maximum

temperature and spin speed values set for the selected

cycle, or the most recently-used settings if they are

compatible with the selected cycle. The temperature

can be decreased by pressing the button, until

the cold wash “OFF” setting is reached. The spin

speed may be progressively reduced by pressing

the button, until it is completely excluded (the

“OFF” setting). If these buttons are pressed again, the

maximum values are restored.

! Exception: if the 4 programme is selected, the

temperature can be increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option has been

activated, the symbol lights up on the display. To

remove the delayed start setting, press the button until

the text “OFF” appears on the display.

Set the desired wash intensity.

Option makes it possible to optimise washing based

on the level of soil in the fabrics and on desired wash

cycle intensity.

Select the wash programme: the cycle will be

automatically set to “ ” as optimised for garments Normal

with an average level of soil (this setting is not applicable

to the “Wool” cycle, which is automatically set to

“ ”).Delicate

For heavily-soiled garments press button until

the “ ” level is reached. This level ensures Intensive

a high-performance wash due to a larger quantity of

water used in the initial phase of the cycle and due to

increased drum rotation. It is useful when removing the

most stubborn stains.

For lightly-soiled garments or a more delicate treatment

of the fabrics, press button until the “ ” Delicate

level is reached. The cycle will reduce drum rotation

to ensure washing results that are perfect for delicate

garments.

Modify the cycle settings.

• Press the button to enable the option; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. Press the START/START THE WASH CYCLE.

PAUSE button. The corresponding indicator light will

turn green, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED symbol will

be lit). To change a wash cycle while it is in progress,

pause the washing machine using the START/PAUSE

button (the START/PAUSE indicator light will flash

slowly in an amber colour); then select the desired cycle

and press the START/PAUSE button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened (wait

approximately 3 minutes). Press the START/PAUSE

button again to restart the wash cycle from the point at

which it was interrupted.

8. This will be THE END OF THE WASH CYCLE.

indicated by the text “END” on the display; when the

DOOR LOCKED symbol switches off the door may

be opened (wait approximately 3 minutes). Open the

door, unload the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

Product specificaties

Merk:	Hotpoint
Categorie:	Wasmachine
Model:	WMBF 742P UK.M

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint WMBF 742P UK.M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wasmachine Hotpoint

Hotpoint NDB 10748 WA Handleiding

7 April 2025

Hotpoint NSWF 742U BS UK Handleiding

20 Februari 2025

Hotpoint NSWM 742U GG UK Handleiding

20 Februari 2025

Hotpoint NWS 7469 WK SPT Handleiding

10 Februari 2025

Hotpoint WMTG 626BS IT Handleiding

15 Januari 2025

Hotpoint WMTG 6526BS IT Handleiding

15 Januari 2025

Hotpoint NF97WK IT Handleiding

7 Januari 2025

Hotpoint NFR79W IT Handleiding

7 Januari 2025

Hotpoint H8 99AD GPOWER UK Handleiding

28 December 2024

Hotpoint NSWA 1146 WW UK Handleiding

28 December 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Miele WSE383 WCS Handleiding

8 April 2025

Whirlpool TDLR 6261BS Handleiding

7 April 2025

Whirlpool FFWDD 107448 WBS Handleiding

7 April 2025

Whirlpool FFB 7269 BV Handleiding

7 April 2025

Arcelik 9120 MP OG Handleiding

6 April 2025

Vedette VLT1155W Handleiding

5 April 2025

Vedette VLT1255W2 Handleiding

5 April 2025

Vedette VLT612E2 Handleiding

5 April 2025

Vedette VLT6112at Handleiding

5 April 2025

Vedette LTV6011 Handleiding

5 April 2025