Hotpoint WDPG 8640X Handleiding

Hotpoint Wasmachine WDPG 8640X

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint WDPG 8640X (16 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

English,1

WASHER-DRYER

! This symbol reminds you to read this instruction manual.

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washer-dryer, 6-7

Control panel

Display

How to run a wash cycle or a drying cycle, 8

Wash cycles and options, 9

Table of programmes and wash cycles

Wash options

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Precautions and advice, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water and electricity supplies

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13-14

Assistance, 15-16

WDPG 8640

Instructions for use

Installation

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose carpet,

adjust the feet in such a way as to allow enough room for

ventilation beneath the washer-dryer.

Electric and water connections

Connecting the water inlet hose

1. Connect the supply pipe

by screwing it to a cold

water tap using a

3/4 gas threaded

connection (see figure).

Before performing the

connection, allow the

water to run freely until it is

perfectly clear.

2. Connect the other end of

the water inlet hose to the

washer-dryer,

screwing it onto the

appliance’s cold water inlet,

situated on the top right-

hand side on the rear of the

appliance (see figure).

3. Make sure there are no kinks or bends in the hose.

! The water pressure at the tap must be within the values

indicated in the Technical details table (on the page 5).

! If the water inlet hose is not long enough, contact a

specialist store or an authorised serviceman.

! Ensure that the supply taps are allowing water through.

Old taps may seize in the closed position and thus

prevent water reaching the machine.

! Never use second-hand or old inlet hoses; use the

products supplied with the machine.

! Keep this instruction manual in a safe place for future

reference. Should the appliance be sold, transferred or

moved, make sure the instruction manual accompanies the

washer-dryer to inform the new owner as to its operation and

features.

! Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

! This is a separate part of

the polystyrene base and

should be removed with

the base.

! IMPORTANT check

when unpacking your

machine.

1. Unpack the washer-dryer.

2. Check whether the washer-dryer has been damaged

during transport. If this is the case, do not install it and

contact your retailer.

3. Remove the 4 protective

screws and the rubber bush

with the respective spacer,

situated on the rear of the

appliance (see also the

installation leaflet).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if the

washer-dryer needs to be moved to another location.

! Packaging materials are not children’s toys.

Levelling

Your machine may make a considerable amount of noise if

the two front feet have not been adjusted correctly.

1. Install the washer-dryer

on a flat sturdy floor, without

resting it up against walls,

furniture cabinets or other.

2. If the floor is not perfectly level, compensate for any

unevenness by tightening or loosening the adjustable

front feet (see figure); the angle of inclination, measured

according to the worktop, must not exceed 2°.

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall drain

situated between 65 and

100 cm from the floor;

The drain hose may

be connected to an

under-sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks or

removable ends have been

taken off the spigot.

If it is placed over the edge

of a basin or sink be sure

the free end of the hose

should not be underwater.

! We advise against the use of hose extensions; in case of

absolute need, the extension must have the same diameter

as the original hose and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a standpipe, that

the end does not go down more than 15cms (6 inches).

If the hose is pushed down too far, this may cause the

machine to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket, make

sure that:

• the socket is earthed and in compliance with the

applicable law;

• the socket is able to sustain the appliance’s maximum

power load indicated on the Technical Data Plate fixed

on the machine;

• the supply voltage is included within the values indica-

ted on the Technical Data Plate fixed on the machine.

• the socket is compatible with the washer-dryer’s plug. If

this is not the case, replace the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate use.

Before using the appliance please read the instructions

below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse

cover re-fitted. If the fuse cover is lost, the plug must not

be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or the

colour that is embossed in words on the base of the plug.

Replacements can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable through

partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewireable plug

bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally inserted

into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Product specificaties

Merk:	Hotpoint
Categorie:	Wasmachine
Model:	WDPG 8640X
Apparaatplaatsing:	Vrijstaand
Soort bediening:	Knoppen
Kleur van het product:	Roestvrijstaal
Ingebouwd display:	Ja
Breedte:	595 mm
Diepte:	605 mm
Hoogte:	850 mm
Type lader:	Voorbelading
Trommelinhoud:	62 l
Uitgestelde start timer:	Ja
Resterende tijd indicatie:	Ja
Kinderslot:	Ja
Energie-efficiëntieklasse (oud):	A
Energieverbruik wassen:	- kWu
Wasklasse:	A
Centrifuge-droger klasse:	A
Onbalanscontrolesysteem:	Ja
Aanpasbare centrifugesnelheid:	Ja
Maximale centrifugesnelheid:	1400 RPM
Droogcapciteit:	6 kg
Energiegebruik bij wassen & drogen:	- kWu
Waterverbruik wassen & drogen:	- l
Aantal wasprogramma's:	4
Kijkglas:	Ja
Watertoevoer:	Koud
Nominale capaciteit (wassen):	8 kg
Type beeldscherm:	LCD
Wasprogramma's:	Hygiene/anti-allergy, Cold, Cotton, Hand/wool, Intensive/outdoor, Synthetics, White, Delicate/silk