Hotpoint OS 897D IX Handleiding

Hotpoint Oven OS 897D IX

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint OS 897D IX (16 pagina's) in de categorie Oven. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

OS 897D IX/HP

OS 897D C IX/HP

Contents

Installation, 2-3

Positioning

Electrical connection

Technical data

Description of the appliance, 4

Overall view

Control panel

Display

Oven structure, 5

Start-up and use, 6-12

Setting the clock

Setting the timer

ExtraLarge Space

Small Space

Main Space

Using the Small Space and Main Space at the same

time

Programming cooking

Practical cooking advice

Cooking advice table for ovens with the ExtraLarge

Space feature

Cooking advice table for the Small Space feature

Cooking advice table for the Main Space feature

Cooking advice table for using the Small Space and

Main Space at the same time

Precautions and tips, 13

General safety

Disposal

Respecting and conserving the environment

Care and maintenance, 14

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

Guarantee, 15

After Sales Service, 16

Operating Instructions

OVEN

English,1

Ventilation

To ensure adequate ventilation is provided, the back

panel of the cabinet must be removed. It is

advisable to install the oven so that it rests on two

strips of wood, or on a completely flat surface with

an opening of at least 45 x 560 mm (see diagrams).

Centring xand fi ing

Position the 4 tabs on the side of the oven so that

they are aligned with the 4 holes on the outer frame.

Adjust the tabs in accordance with the thickness of

the cabinet side panel, as shown below:

20 mm thick: take off the

removable part of the tab (see

diagram).

18 mm thick: use the first

groove, which has already

been set in the factory (see

diagram).

16 mm thick: use the second

groove (see diagram).

Secure the appliance to the cabinet by opening the

oven door and inserting 4 screws into the 4 holes on

the outer frame.

 All parts which ensure the safe operation of the

appliance must not be removable without the aid of

a tool.

 Before operating your new appliance please read

this instruction booklet carefully. It contains

important information concerning the safe operation,

installation and maintenance of the appliance.

 Please keep these operating instructions for future

reference. Pass them on to any new owners of the

appliance.

Positioning

 Keep all packaging material out of reach of

children. It may present a choking or suffocation

hazard (see Precautions and tips).

 The appliance must be installed by a qualified

professional in accordance with the instructions

provided. Incorrect installation may damage

property or cause harm to people or animals.

Built-in appliance

Use a suitable cabinet to ensure that the appliance

functions properly.

 The panels adjacent to the oven must be made of

heat-resistant material.

 Cabinets with a veneer exterior must be

assembled with glues which can withstand

temperatures of up to 100°C.

 To install the oven under the counter (see

diagram) or in a kitchen unit, the cabinet must

have the following dimensions:

 The appliance must not come into contact with

electrical parts once it has been installed.

The indications for consumption given on the data

plate have been calculated for this type of

installation.

595 mm.

24 mm.

545 mm.

5 mm.

576 mm.

23 mm.

593 mm.

45 mm.

558 mm.

547

mm. min.

Installation

560 mm.

45 mm.

Electrical connection

 Ovens equipped with a three-pole power supply

cable are designed to operate with alternating

current at the voltage and frequency indicated on

the data plate located on the appliance (see below).

F w bittingthe poer s lupp y ca le

1. Open the terminal

board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(see diagram).

2. Install the power

supply cable by

loosening the cable

clamp screw and the

three wire contact

screws L-N- .

Connect the wires to

the corresponding

terminals: the Blue wire

to the terminal marked

(N), the Brown wire to

the terminal marked (L)

and the Yellow/Green

wire to the terminal

marked (see diagram).

3. Secure the cable by fastening the clamp screw.

4. Close the cover of the terminal board.

C g e r c c eonn tinec the lect i ity suppl y a lb to the

mains

Install a standardised plug corresponding to the

load indicated on the data plate (see table).

The appliance must be directly connected to the mains

using an omnipolar switch with a minimum contact

opening of 3 mm installed between the appliance and

the mains. The switch must be suitable for the charge

indicated and must comply with current electrical

regulations (the earthing wire must not be interrupted

by the switch). The supply cable must be positioned

so that it does not come into contact with temperatures

higher than 50°C at any point.

 The installer must ensure that the correct electrical

connection has been made and that it is fully

compliant with safety regulations.

Before connecting the appliance to the power

supply, make sure that:

 The appliance is earthed and the plug is compliant

with the law.

 The socket can withstand the maximum power of

the appliance, which is indicated on the data

plate (see below).

 The voltage is in the range between the values

indicated on the data plate (see below).

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it.

Do not use extension cords or multiple sockets.

 Once the appliance has been installed, the power

supply cable and the electrical socket must be

easily accessible.

 The cable must not be bent or compressed.

 The cable must be checked regularly and replaced

by authorised technicians only (see Assistance).

The manufacturer declines any liability should

these safety measures not be observed.

APPLIANCE SPECIFICATIONS

Dimensions

width 43.4 cm

height 39.5 cm

depth 40.8 cm

Volume 70 l

Electrical

connections

voltage: 230 - 240 V~ 50Hz

maximum power absorbed

2600-2800W (see data plate)

ENERGY

LABEL

Directive 2002/40/EC on the

label of electric ovens.

Standard EN 50304

Declared energy consumption

for Forced convection Class –

heating mode:

Gratin.

This appliance conforms to the

following European Economic

Community directives:

2006/95/EEC dated 12/12/06

(Low Voltage) and subsequent

amendments –

2004/108/EEC dated 15/12/04

(Electromagnetic Compatibility)

and subsequent amendments -

93/68/EEC dated 22/07/93 and

subsequent amendments.

2002/96/EEC and subsequent

amendments.

1275/2008 stand-by/off mode.

Product specificaties

Merk:	Hotpoint
Categorie:	Oven
Model:	OS 897D IX
Soort bediening:	Sensor
Kleur van het product:	Roestvrijstaal
Breedte:	595 mm
Hoogte:	595 mm
Verlichting binnenin:	Ja
Totale binnen capaciteit (ovens):	70 l
Aantal ovens:	1
Soort oven:	Elektrische oven
Type timer:	Digitaal
Instelbare thermostaat:	Ja