Hotpoint NSWM 843C W UK N Handleiding

Hotpoint Wasmachine NSWM 843C W UK N

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint NSWM 843C W UK N (3 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 77 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Quick Guide

THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.

To receive more comprehensive assistance, register the

appliance on

www.hotpoint.eu/register

Before using the appliance carefully read the Health and Safety guide.

Before using the machine, it is imperative that the transport bolts are removed. For more

detailed instructions on how to remove them, see the Installation Guide.

CONTROL PANEL

WASH CYCLE TABLE

* By selecting the cycle and excluding the spin cycle, the washing machine will Spin & Drain

drain only.

** The duration of the wash cycles can be checked on the display.

*** If “Steam Hygiene” option is set, the duration of the wash cycles will increase.

****

After programme end and spinning with maximum selectable spin speed, in default

programme setting.

4) Eco Cotton - Test wash cycles in compliance with regulations 1061/2010. Set

“Cotton”

wash cycle at a temperature of 40°C or 60°C to access this cycles.

The cycle duration indicated on the display or instruction manual is an estimate based on

standard conditions. The actual duration may vary in relation to several factors, such as the

temperature and pressure of the incoming water, ambient temperature, amount of detergent,

load quantity and type, load balancing and any additional options selected.The values given

for programmes other than the Eco 40-60 programme are indicative only.

1) Eco 40-60 - Test wash cycle in compliance with EU Ecodesign regulation 2019/2014. The most efficient

programme in terms of energy and water consumption for washing normally soiled cotton laundry.

Note: spin speed values shown on the display can slightly differs from the values stated in the table.

For all testing institutes:

2) Long cotton cycle: set programme at temperature 40°C. Cotton

3) Long synthetics cycle: set cycle at a temperature of 40°C.Synthetics

PRODUCT DESCRIPTION

1. Top

2. Detergent dispenser drawer

3. Control panel

4. Handle

5. Porthole door

6. Drain pump (behind the plinth)

7. Plinth (removable)

8. Adjustable feet (2)

1. ON/OFF button

2. KEY LOCK button

3. EXTRA TOUCH button

4. EXTRA TOUCH indicator lights

5. START/PAUSE button and indicator light

6. OPTION button and indicator light

7. DELAY START button

8. SPIN button

9. TEMPERATURE button

10. WASH CYCLE SELECTOR KNOB

DETERGENT DISPENSER DRAWER

Compartment *:

Do not insert detergent in this compartment.

Compartment 1: Washing detergent (powder

or liquid)

If liquid detergent is used, the removable plastic

partition (supplied) should be used for proper A

dosage.

If powder detergent is used, place the partition

into slot .B

Compartment 2: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “MAX” level.

! Use powder detergent for white cotton garments, for pre-washing, and

for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

DISPLAY

567

Delay

To set a delayed start for the selected cycle, press the corresponding

button repeatedly until the desired delay period is reached. When this

option has been activated, the symbol lights up on the display. To

remove the delayed start setting, press the button until “OFF” appears on

the display.

Temperature

Each wash cycle has a pre-dened temperature. To modify the

temperature, press the button. The value will appear on the display.

Spin

Each wash cycle has a pre-dened spin speed. To modify the spin speed,

press the button. The value will appear on the display.

KEY LOCK

To activate the control panel lock, press and hold the button for

approximately 2 seconds. When the symbol is lit, the control panel is

locked (except for the ON/OFF button). This will prevent accidental

modications to wash cycles, especially when children are at home. To

deactivate the control panel lock, press and hold the button for

approximately 2 seconds.

TIPS AND SUGGESTIONS

Divide the laundry according to:

Type of fabric (cotton, mixed bres, synthetics, wool, garments to be

hand-washed). Colour (separate coloured garments from whites, wash

new coloured garments separately). Delicates (small garments – such as

nylon stockings – and items with hooks – such as bras: insert them in a

fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washing machine and

the drum. Check all buttons.

Follow the dosage recommendation / additives

It optimizes the cleaning result, it avoids irritating residues of surplus

detergent in your laundry and it saves money by avoiding waste of surplus

detergent

Use low temperature and longer duration

The most ecient programmes in terms of energy consumption are

generally those that perform at lower temperatures and longer duration.

Observe the load sizes

Load your washing machine up to the capacity indicated in the

“PROGRAMME CHART” table to save water and energy.

Noise and remaining moisture content

They are inuenced by the spinning speed: the higher the spinning speed

in the spinning phase, the higher the noise and the lower the remaining

moisture content.

CARE AND MAINTENANCE

For any cleaning and maintenance, switch o and unplug the washing

machine. Do not use ammable uids to clean the washing machine.

Clean and maintain your washing machine periodically (at least 4 times per

year).

Cutting o the water and electricity supplies

Close the water tap after every wash. This will limit wear on the hydraulic

system inside the washing machine and help to prevent leaks.

Unplug the washing machine when cleaning it and during all

maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance can be cleaned

using a soft cloth soaked in lukewarm soapy water. Do not use solvents or

abrasives.

The washing machine has a “Auto-Clean” cycle for its internal parts; it

must be run without any load in the drum.

To optimise this cycle, it is possible to use either detergent (10% of the

quantity specied for lightly soiled garments) or special additives to clean

the washing machine. We recommend running a cleaning cycle every 40

wash cycles.

To start the programme, close the door, turn the machine ON and press

button for 5 seconds.

The cycle will start automatically and will run for about 70 minutes. To

stop the cycle, press the START/PAUSE button.

Cleaning the detergent dispenser drawer

Remove the dispenser drawer by lifting and pulling it outwards. Wash it

under running water; this procedure should be eected regularly.

Caring for the door and drum

Always leave the porthole door ajar in order to prevent unpleasant

odours from forming.

Cleaning the pump

The washing machine is tted with a self-cleaning pump that does not require

any maintenance. Small items (such as coins or buttons) may sometimes fall

into the protective pre-chamber situated at the base of the pump.

! Make sure that the wash cycle has ended and unplug the appliance.

To access the pre-chamber:

1. remove the covering panel on the front side of the machine by inserting

a screwdriver in the centre and sides of the panel and using it as a lever;

2. loosen the drainage pump cover by turning it anti-clockwise: it is

normal for some water to leak out;

3. clean the inside thoroughly;

4. screw the cover back on;

5. put the panel back in place, making sure the hooks slot in place before

pushing the panel onto the appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If it is cracked or broken, it

must be replaced: during wash cycles, the high pressure of the water

could suddenly split the hose open.

! Never use hoses that have already been used.

LOAD BALANCING SYSTEM

Before every spin cycle, to avoid excessive vibrations before every

spin and to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the washing

rotation speed. If, after several attempts, the load is not balanced

correctly, the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washing machine performs the distribution

process instead of spinning. To encourage improved load distribution and

balance, we recommend small and large garments are mixed in the load.

ACCESSORIES

Contact our Technical Assistance Service to check whether the following

accessories are available for this washing machine model.

Stacking kit

With this accessory you can secure the tumble dryer to the upper part of

your washing machine to save space and facilitate loading and unloading

of the tumble dryer.

TRANSPORT AND HANDLING

Do not lift the washing machine by gripping it from the upper section.

Unplug the appliance and close the water tap. Check that the door and

detergent dispenser drawer are tightly closed. Detach the lling hose

from the water tap then detach the drain hose. Empty all the water

remaining in the hoses and secure the latter so that they do not get

damaged during transport. Apply the transport bolts back on. Repeat, in

reverse order, the transport bolt removal procedure described in the

“Installation instructions”.

TROUBLESHOOTING

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily

solved using the following list.

Anomalies Possible causes / Solution

The washing machine does

not start.

The appliance is not plugged into the socket fully, or not enough to make contact.

There is no power in the house.

The wash cycle does not start.

The washing machine door is not closed properly.

The ON/OFF button has not been pressed.

The START/PAUSE button has not been pressed.

The water tap has not been opened.

A delay has been set for the start time.

The washing machine does

not ll with water (“H2O”

appears on the display).

The water inlet hose is not connected to the tap.

The hose is bent.

The water tap has not been opened.

There is no water supply in the house.

The pressure is too low.

The START/PAUSE button has not been pressed.

The washing machine

continuously loads and

unloads water.

The drain hose is not tted between 65 and 100 cm from the oor.

The free end of the hose is immersed in water.

The wall drainage system is not tted with a breather pipe.

If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the

Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems relating

to back-siphonage, causing the washing machine to ll with water and drain continuously. Special anti-siphon

valves are available in shops and help to prevent this inconvenience.

The washing machine does

not drain or spin.

The cycle does not include drainage: with certain cycles it must be started manually.

The drain hose is bent.

The drainage duct is clogged.

The washing machine

vibrates a lot during the spin

cycle.

The drum was not unlocked correctly during installation.

The washing machine is not level.

The washing machine is tucked between furniture cabinets and the wall.

The washing machine leaks.

The water inlet hose is not screwed on properly.

The detergent dispenser drawer is obstructed.

The drain hose is not properly attached.

The “Options” and START/

PAUSE indicator lights

ash rapidly and the display

visualises an error code (e.g.:

F-01, F-...).

Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

There is too much foam.

The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and

machine wash”, or the like).

Too much detergent was used.

After pressing START/PAUSE

button, the drum turns

but the washing machine

does not ll water and no

error on display.

See “DEMO MODE”

You can download the SAFETY AND INSTALLATION INSTRUCTIONS, TECHNICAL SHEET and ENERGY DATA

by:

• Visiting the website http://docs.hotpoint.eu.

• Using the QR code.

• Alternatively, contact our Technical Assistance Service (the telephone number is indicated in the warranty

booklet). When contacting the Technical Assistance Service, provide the codes shown on the adhesive label applied

to the inside of the door.

For User’s Repair & Maintenance Information visit www.hotpoint.eu.

The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the

model identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu

xxx

xxxx

DEMO MODE: to deactivate this function, switch the washing machine OFF. Than press and hold “Start/Pause” button, within 5 seconds

press also “ON/OFF” button and hold both buttons for 2 seconds.

400011508539

Product specificaties

Merk:	Hotpoint
Categorie:	Wasmachine
Model:	NSWM 843C W UK N
Apparaatplaatsing:	Vrijstaand
Soort bediening:	Buttons, Rotary
Kleur van het product:	Wit
Deurscharnieren:	Links
Ingebouwd display:	Ja
Breedte:	600 mm
Diepte:	580 mm
Hoogte:	850 mm
Type lader:	Voorbelading
Deurkleur:	Wit
Uitgestelde start timer:	Ja
Resterende tijd indicatie:	Ja
Kinderslot:	Ja
Geluidsniveau:	82 dB
Energie-efficiëntieklasse:	D
Waterconsumptie per cyclus:	48 l
Centrifuge-droger klasse:	B
Geluidsniveau (wassen):	- dB
Sopschuimbewaking:	Ja
Aanpasbare centrifugesnelheid:	Ja
Maximale centrifugesnelheid:	1400 RPM
Geluidsemissieklasse:	D
Geluidsniveau bij centrifugeren:	- dB
Restvochtpercentage:	53 procent
Cyclustijd (max):	210 min
Energieverbruik per 100 cycli:	71 kWu
Aan-/uitknop:	Ja
Instelbare temperatuur:	Ja
Kijkglas:	Ja
Uitgave lade type:	3-weg
Nominale capaciteit:	8 kg
AC-ingangsspanning:	220 - 240 V
AC-ingangsfrequentie:	50 Hz
Energie-efficiëntieschaal:	A tot G
Kleur deurgreep:	Wit