Hotpoint NSWF 945C BS UK N Handleiding

Hotpoint Wasmachine NSWF 945C BS UK N

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Hotpoint NSWF 945C BS UK N (3 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
GB
Quick Guide
THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.
To receive more comprehensive assistance, register the
appliance on
www.hotpoint.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more
detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
WASH CYCLE TABLE
* By selecting the cycle and excluding the spin cycle, the washing machine will Spin & Drain
drain only.
** The duration of the wash cycles can be checked on the display.
***
After programme end and spinning with maximum selectable spin speed, in default
programme setting.
**** The display will show the suggested spin speed as default value.
! If β€œSteam Hygiene” option is set, the duration of the wash cycles will increase.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as the
temperature and pressure of the incoming water, ambient temperature, amount of detergent,
load quantity and type, load balancing and any additional options selected.The values given
for programmes other than the Eco 40-60 programme are indicative only.
1) Eco 40-60 - Test wash cycle in compliance with EU Ecodesign regulation 2019/2014. The most efficient
programme in terms of energy and water consumption for washing normally soiled cotton laundry.
Note: spin speed values shown on the display can slightly differs from the values stated in the table.
For all testing institutes:
2) Long cotton cycle: set programme at temperature 40Β°C. Cotton
3) Long synthetics cycle: set cycle at a temperature of 40Β°C.Synthetics
PRODUCT DESCRIPTION
1.
3.
2.
5.
4.
7.
6.
8.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
1. ON/OFF button
2. KEY LOCK button
3. EXTRA TOUCH button
4. EXTRA TOUCH indicator lights
5. START/PAUSE button and indicator light
6. OPTION button and indicator light
7. DELAY START button
8. SPIN button
9. TEMPERATURE button
10. WASH CYCLE SELECTOR KNOB
Maximum load
9 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Detergents and
Additives
Recommended
detergent
Residual
dampness %
(***)
Energy
consumption
kWh
Total water lt
Laundry
temperature
Β°C
Wash cycle Temperature Maximum
spin
(r.p.m.)
Max.
load
(kg)
Duration
(h : m)
Wash Fabric
softener Powder Liquid
Setting Range 1 2
Mixed 40Β°C - 40Β°C 1400 9,0 ** ο„‘ ο„Œ β€“ο€Œβ€“β€“β€“β€“
Eco 40-60 (1) 40 Β°C 40Β°C
1351 9,0 3:40 ο„‘ ο„Œ ο€Œ ο€Œ 53 0,81 57 33
1351 4,5 2:50 ο„‘ ο„Œ ο€Œ ο€Œ 53 0,57 50 35
1351 2,5 2:40 ο„‘ ο„Œ ο€Œ ο€Œ 53 0,36 44 28
Cotton (2) 40Β°C - 60Β°C 1400 9,0 3:55 ο„‘ ο„Œ ο€Œ ο€Œ 49 1,10 97 45
Synthetics (3) 40Β°C - 60Β°C 1200 4,5 2:55 ο„‘ ο„Œ ο€Œ ο€Œ 35 0,80 55 43
Delicates 40Β°C - 40Β°C 1000 4,5 ** ο„‘ ο„Œ β€“ο€Œβ€“β€“β€“β€“
Wool 40Β°C - 40Β°C 800 2 ** ο„‘ ο„Œ β€“ο€Œβ€“β€“β€“β€“
Anti Allergy 60Β°C 40Β°C - 60Β°C 1400 5 ** ο„‘ ο„Œ ο€Œ ο€Œ ––––
Spin & Drain * – – 1400 9,0 ** – – – – – – – –
Rinse & Spin – – 1400 9,0 ** – ο„Œβ€“β€“β€“β€“β€“β€“
Baby 40Β°C - 40Β°C 1200 (****) 4,0 ** ο„‘ ο„Œ β€“ο€Œβ€“β€“β€“β€“
20Β°C 20 Β°C - 20 Β°C 1400 9,0 1:50 ο„‘ ο„Œ β€“ο€Œ54,5 0,14 78 22
Duvet 30Β°C - 30Β°C 1000 3,5 ** ο„‘ ο„Œ β€“ο€Œβ€“β€“β€“β€“
White 40Β°C - 90Β°C 1400 9,0 2:00 ο„‘ ο„Œ ο€Œ – 54,6 0,89 89 42
30 min 30Β°C - 30Β°C 1200 (****) 4,5 0:30 ο„‘ ο„Œ β€“ο€Œ71 0,18 37 27
Full Load 45 min 40Β°C - 40Β°C 1200 9,0 ** ο„‘ ο„Œ β€“ο€Œβ€“β€“β€“β€“
Anti Stain 40Β° 40Β°C - 40Β°C 1400 9,0 ** ο„‘ ο„Œ β€“ο€Œβ€“β€“β€“β€“
ο„‘
Required dosage Optional dosageο„Œ
DETERGENT DISPENSER DRAWER
Compartment *:
Do not insert detergent in this compartment.
Compartment 1: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
partition (supplied) should be used for proper A
dosage.
If powder detergent is used, place the partition
into slot .B
Compartment 2: Additives (fabric softeners, etc.)
The fabric softener must not exceed the β€œMAX” level.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60Β°C.
! Follow the instructions given on the detergent packaging.
1
2
A
B
*
1
10
2
DISPLAY
4
567
89
3
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Mixed
For washing lightly to normally soiled resistant garments in cotton, linen,
synthetic bres and mixed bres.
Eco 40-60
For washing normally soiled cotton garments declared to be washable at 40
Β°C or 60 Β°C, together in the same cycle. This is the standard cotton programme
and the most ecient in terms of water and energy consumption.
! The cycle runs only at 40Β°C as per regulation.
Cotton
Suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Synthetics
Suitable for washing moderately soiled garments made of synthetic bres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.
Delicates
Suitable for washing lightly soiled garments made of synthetic bres (e.g.
polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.
Wool - Wool Care
The wool wash cycle of this machine has been approved by
The Woolmark Company for the washing of machine washable
wool products provided that the products are washed
according to the instructions on the garment label and those
issued by the manufacturer of this washing machine. The
Woolmark symbol is a Certication mark in many countries. M2225.
Anti Allergy
Suitable for removing major allergens such as pollen, mites and cat or
dog hair.
Spin & Drain
Spins the load then empties the water. For resilient garments. If you
exclude the spin cycle, the machine will drain only.
Rinse & Spin
Rinses and then spins. For resilient garments.
Baby
Use the special wash cycle to remove the soiling typically caused by
babies, while removing all traces of detergent from nappies in order to
prevent the delicate skin of babies from suering allergic reactions. The
cycle has been designed to reduce the amount of bacteria by using a
greater quantity of water and optimising the eect of special disinfecting
additives added to the detergent.
20Β°C
For washing lightly soiled cotton garments, at a temperature of 20 Β°C.
Duvet
Suitable for washing clothing padded with goose down, such as single
duvets (weighing under 3,5 kg), cushions or down jackets. Duvets should
be loaded into the drum with their edges folded inwards and no more
than ΒΎ of the total drum volume should be used up. For best results, it is
advisable to use liquid detergent to be poured into the detergent drawer.
White
For heavily soiled whites and resistant colours.
30 min
For washing lightly soiled garments in a short time. Not suitable for wool,
silk and garments to be washed by hand.
Full Load 45 min
Suitable for washing a full load of cotton clothes moderately soiled in 45
minutes.
Anti Stain 40Β°
the programme is suitable to heavily-soiled garments with resistant
colours. It ensures a washing class that is higher than the standard class (A
class). When running the programme, do not mix garments of dierent
colours. We recommend the use of powder detergent. Pre-treatment with
special additives is recommended if there are particularly obstinate stains.
DISPLAY
The display is useful when programming the washing machine and
provides plenty of information.
The duration of the available wash cycles and the remaining time of a running
cycle appear (the display will show the maximum duration of the cycle chosen,
which may decrease after several minutes, since the eective duration of the
programme varies depending on the wash load and the settings chosen); if the
DELAY START option has been set, the countdown to the start of the selected
wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin
speed and temperature values attained by the machine during the set
wash cycle, or the values selected most recently, if these are compatible
with the set wash cycle.
Locked door indicator
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns o before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is o, the door can be opened.
FIRSTTIME USE
Once the appliance has been installed, and before it is used for the rst
time, run a wash cycle with a very little detergent and no laundry, by
setting the β€œAuto-Clean” cycle. (see β€œ ”)CARE AND MAINTENANCE
DAILY USE
Prepare the laundry by following the suggestions appearing under the
β€œTIPS AND SUGGESTIONS” section.
- Press the ON/OFF button ; the indicator light relative to START/PAUSE
will ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the wash cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments, as described in the β€œDETERGENT DISPENSER
DRAWER” section.
- Close the door.
- Select the desired wash cycle.
- Pressing the button gradually reduces the temperature down to the
cold wash β€œOFF” setting. Pressing the button gradually reduces the spin
speed until it is completely excluded (β€œOFF” setting). Pressing the buttons
further restores the maximum allowed values for the selected cycle.
- Select the desired options.
STARTING CYCLE
- Press the START/PAUSE button.
The machine will lock the door ( symbol on) and the drum will start to
rotate; the door will be unlocked ( symbol OFF) and then locked again
( symbol on) as preparation phase of each washing cycle. The β€œClicking”
noise is part of the door locking mechanism. Water will enter the drum
and start the washing phase once the door is locked.
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
indicator light will ash amber. To start the wash cycle from the point at
which it was interrupted, press the START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the symbol turns on to signal that the door cannot
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE button to pause the cycle; the
indicator light will ash amber. If the symbol is not lit, the door may be
opened. Press the START/PAUSE button again to continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE button (the relative indicator light will ash
amber), then select the desired cycle and press the START/PAUSE
button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch o.
AT THE END OF THE WASH CYCLE
This will be indicated by the word β€œEND” on the display; when the
symbol switches o, the door may be opened. Open the door, unload the
laundry and switch o the machine. If you do not press β€œON/OFF”
button, the washing machine will switch o automatically after about a
10 minutes.
OPTIONS
- If the selected option is not compatible with the set wash cycle, the
indicator light will ash and the option will not be activated.
Extra Rinse
Selecting this option allows for enhancing rinsing eciency and fully
removing the detergent. It is particularly useful for sensitive skin.
EX
EX
EX
EX
EX
T
T
T
T
T
R
R
R
R
R
A
A
A
A
A
T
T
T
T
T
OUC
OUC
OUC
OUC
OUC
H
H
H
H
H
Extra Touch
After pushing the button for the 1st time, option β€œRapid Option” is
selected and the cycle duration will be reduced.
After pushing the button for the 2nd time, option β€œSteam Hygiene”
enhances washing performance by generating steam during the wash
cycle to remove any bacteria from the bres, which are treated at the same
time.
! The steam generated during the operation of the washing machine may
cause the porthole door to become hazy.
h
TROUBLESHOOTING
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily
solved using the following list.
Anomalies Possible causes / Solution
The washing machine does
not start.
The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power in the house.
The wash cycle does not start.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The washing machine does
not ll with water (β€œH2O”
appears on the display).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The washing machine
continuously loads and
unloads water.
The drain hose is not tted between 65 and 100 cm from the oor.
The free end of the hose is immersed in water.
The wall drainage system is not tted with a breather pipe.
If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the
Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems relating
to back-siphonage, causing the washing machine to ll with water and drain continuously. Special anti-siphon
valves are available in shops and help to prevent this inconvenience.
The washing machine does
not drain or spin.
The cycle does not include drainage: with certain cycles it must be started manually.
The drain hose is bent.
The drainage duct is clogged.
The washing machine
vibrates a lot during the spin
cycle.
The drum was not unlocked correctly during installation.
The washing machine is not level.
The washing machine is tucked between furniture cabinets and the wall.
The washing machine leaks.
The water inlet hose is not screwed on properly.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The β€œOptions” and START/
PAUSE indicator lights
ash rapidly and the display
visualises an error code (e.g.:
F-01, F-...).
Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam.
The detergent is not suitable for machine washing (it should display the text β€œfor washing machines” or β€œhand and
machine wash”, or the like).
Too much detergent was used.
After pressing START/PAUSE
button, the drum turns
but the washing machine
does not ll water and no
error on display.
See β€œDEMO MODE”
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
β€’ Visiting the website andhttp://docs.hotpoint.eu. parts-selfservice.whirlpool.com
β€’ Using the QR code.
β€’ Alternatively, contact our Technical Assistance Service (the telephone number is indicated in the warranty
booklet). When contacting the Technical Assistance Service, provide the codes shown on the adhesive label applied
to the inside of the door.
For User’s Repair & Maintenance Information visit www.hotpoint.eu.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the
model identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu
xxxxxxxxxxxx
DEMO MODE: to deactivate this function, switch the washing machine OFF. Than press and hold β€œStart/Pause” button, within 5 seconds
press also β€œON/OFF” button and hold both buttons for 2 seconds.
400011660453

Product specificaties

Merk: Hotpoint
Categorie: Wasmachine
Model: NSWF 945C BS UK N

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint NSWF 945C BS UK N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wasmachine Hotpoint

Hotpoint

Hotpoint H6 08 GPOWER IT Handleiding

2 December 2024
Hotpoint

Hotpoint NR 849G WS A IT Handleiding

2 December 2024
Hotpoint

Hotpoint NG98W IT Handleiding

2 December 2024
Hotpoint

Hotpoint NF746WK IT Handleiding

2 December 2024
Hotpoint

Hotpoint H7 99 GPOWER IT Handleiding

2 December 2024
Hotpoint

Hotpoint NBT 116 BLACK IT Handleiding

2 December 2024
Hotpoint

Hotpoint NLCD 946 WC A EU N Handleiding

2 December 2024
Hotpoint

Hotpoint BI WMHG 81485 EU Handleiding

2 December 2024
Hotpoint

Hotpoint BI WDHG 861485 EU Handleiding

2 December 2024
Hotpoint

Hotpoint NM11 846 WS A EU N Handleiding

2 December 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Asko

Asko w 6362 l tit Handleiding

5 December 2024
Asko

Asko W2084.W-2 Handleiding

5 December 2024
Bauknecht

Bauknecht BPW 1014 A Handleiding

21 December 2024
Asko

Asko w 6362lt Handleiding

5 December 2024
Svan

Svan SL8201DD Handleiding

21 December 2024
Svan

Svan SLI8200D Handleiding

21 December 2024
Svan

Svan SL9401AIDB Handleiding

21 December 2024
Svan

Svan SL7201DD Handleiding

21 December 2024
Electrolux

Electrolux EWD8462OBI Handleiding

20 December 2024
Svan

Svan SL6001DD Handleiding

20 December 2024