Hotpoint NM11 946 WS A UK N Handleiding

Hotpoint Wasmachine NM11 946 WS A UK N

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint NM11 946 WS A UK N (4 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Quick Guide

THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.

To receive more comprehensive assistance, register the

appliance on

www.hotpoint.eu/register

Before using the appliance carefully read the Health and Safety guide.

Before using the machine, it is imperative that the transport bolts are removed. For more

detailed instructions on how to remove them, see the Installation Guide.

CONTROL PANEL

WASH CYCLE TABLE

For all testing institutes:

2) Long cotton cycle: set wash cycle Cotton with a temperature of 40°C.

3) Long synthetics cycle: set wash cycle with a temperature of 40°C.Synthetics

* By selecting the cycle and excluding the spin cycle, the washing machine will Spin & Drain

drain only.

** The duration of the wash cycles can be checked on the display.

*** For Prewash press the “Temp.” button until the symbol lights up (only 90°).

****

After programme end and spinning with maximum selectable spin speed, in default

programme setting.

4) The display will show the suggested spin speed as default value.

The cycle duration indicated on the display or instruction manual is an estimate based on

standard conditions. The actual duration may vary in relation to several factors, such as the

temperature and pressure of the incoming water, ambient temperature, amount of detergent,

load quantity and type, load balancing and any additional options selected.The values given

for programmes other than the Eco 40-60 programme are indicative only.

1) Eco 40-60 - Test wash cycle in compliance with EU Ecodesign regulation 2019/2014. The

most ecient programme in terms of energy and water consumption for washing normally

soiled cotton laundry.

Note: spin speed values shown on the display can slightly diers from the values stated in

the table.

PRODUCT DESCRIPTION

1. Top

2. Detergent dispenser drawer

3. Control panel

4. Handle

5. Porthole door

6. Drain pump (behind the plinth)

7. Plinth (removable)

8. Adjustable feet (2)

Maximum load 9 kg

Power input in o mode 0.5 W / in left-on mode 8 W Add

Gar-

ments

( )

Detergents and

Additives Recommended

detergent

Residual

dampness % (****)

Energy

consumption kWh

Total water lt

Laundry

temperature °C

Wash cycle

Temperature Max.

spin speed

(rpm)

Max.

load

(kg)

Dura-

tion

(h : m)

Pre-

wash Wash Fabric

softener Pow-

der Liquid

Setting Range 1 2 3

Eco 40-60 (1) 40 °C 40°C

1351 9,0 3:45 – –    53 0,80 59 32

1351 4,5 2:50 – –    53 0,48 52 29

1351 2,5 2:10 – –    53 0,24 41 25

Cotton (2) 40°C - 60°C 1400 9,0 3:55 – –    49 1,10 97 45

Synthetics (3) 40°C - 60°C 1200 4,5 2:55 – –    35 0,80 55 43

Mixed 40°C - 40°C 1400 9,0 **   –  –– – – –

Delicates 40°C - 40°C 1000 4,5 **   –  –– – – –

White 40°C - 90°C 1400 9,0 2:00       (***) 55 0,89 89 42

Anti Stain 40° 40°C - 40°C 1000 4,5 **   –    – – – –

Rapid 30 min 30°C - 30°C 1200 (4) 4,5 0:30   –  –71 0,18 37 27

Spin & Drain * – – 1400 9,0 ** – – – – – – – – – – –

Rinse & Spin – – 1400 9,0 ** – – – – – – – – – –

Steam Refresh – – – 2,0 ** – – – – – – – – – – –

20°C 20 °C - 20 °C 1400 9,0 1:50 – –  –55 0,14 78 22

Wool 40°C - 40°C 800 2,0 ** – –  –– – – –

Anti Allergy 60°C 140040°C - 60°C 5,0 ** – –    – – – –

Bed & Bath 60°C - 60°C 1400 9,0 **   –    – – – –

  Dosing required Dosing optional

DETERGENT DISPENSER DRAWER

compartment 1: Pre-wash detergent (powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

If liquid detergent is used, it is recommended that

the removable plastic partition A (supplied) be

used for proper dosage.

If powder detergent is used, place the partition

into slot B.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overow the grid.

! Use powder detergent for white cotton

garments, for pre-washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

1. STEAM HYGIENE / MUTE button

2. FINAL CARE / KEY LOCK button

3. ON/OFF button

4. ACTIVE CARE button and indicator light

5. START/PAUSE button

6. RAPID / GREEN button

7. SPIN button

8. START DELAY button

9. TEMPERATURE button

10. WASH CYCLE SELECTOR KNOB

1 2

56789

DISPLAY

WASH CYCLES

Follow the instructions on the symbols of the garment’s wash

care label. The value indicated in the symbol is the maximum

recommended temperature for washing the garment.

Eco 40-60

For washing normally soiled cotton garments declared to be washable

at 40 °C or 60 °C, together in the same cycle. This is the standard cotton

programme and the most ecient in terms of water and energy

consumption.

Cotton

Normally to heavily soiled and robust cottons.

Synthetics

Suitable for washing moderately soiled garments made of synthetic bres

(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.

Mixed

For washing lightly to normally soiled resilient garments in cotton, linen,

synthetic bres and mixed bres.

Delicates

For washing very delicate garments. It is advisable to turn the garments

inside out before washing them. For best results, use liquid detergent on

delicate garments.

White

For washing normally to heavily soiled towels, underwear, table and bed

linen, etc in resilient cotton and linen. Only when the temperature is

selected at 90°C the cycle is provided with a prewash phase before main

washing phase. In this case it is recommended to add detergent both, in

the prewash and main wash section.

Anti Stain 40°

The programme is suitable to heavily-soiled garments with resistant

colours. It ensures a washing class that is higher than the standard class (A

class). When running the programme, do not mix garments of dierent

colours. We recommend the use of powder detergent. Pre-treatment with

special additives is recommended if there are obstinate stains.

Rapid 30 min

For washing lightly soiled garments quickly. This cycle lasts only 30

minutes, saving time and energy.

Spin & Drain

Spins the load then empties the water. For resilient garments. If you

exclude the spin cycle, the machine will drain only

Rinse & Spin

Rinses and then spins. For resilient garments.

Steam Refresh

The garments will be damp once the cycle is completed, so we recommend

hanging them to dry (2 kg, roughly 3 items). This programme refreshes

garments by removing bad odours and relaxing the bres. Insert dry items

only (that are not dirty) and select programme “Steam Refresh”. Garments

will be a little damp at the end of the cycle and can be worn after a few

minutes. The “Steam Refresh” programme makes ironing easier.

! Do not add softeners or detergents.

! Not recommended for wool or silk garments.

20°C

For washing lightly soiled cotton garments, at a temperature of 20 °C.

Wool - Wool Care : The wool wash cycle of this machine has been

approved by The Woolmark Company for the washing of machine

washable wool products provided that the products are washed

according to the instructions on the garment label and those issued by

the manufacturer of this washing machine. The Woolmark symbol is a

Certication mark in many countries. M2225.

Anti Allergy

Suitable for removing major allergens such as pollen, mites and cat or dog hair.

Bed & Bath

For washing home linen in a single cycle. It optimises the use of fabric

softener and allows for saving time and electricity. We recommend the

use of powder detergent.

DISPLAY

The display is useful when programming the washing machine and

provides plenty of information.

The duration of the available wash cycles and the remaining time of a

running cycle appear in section (the display will show the maximum A

duration of the cycle chosen, which may decrease after several minutes,

since the eective duration of the programme varies depending on the

wash load and the settings chosen); if the DELAYED START option has been

set, the countdown to the start of the selected wash cycle will appear.

Pressing the corresponding button allows you to view the maximum spin

speed and temperature values attained by the machine during the set

wash cycle, or the values selected most recently, if these are compatible

with the set wash cycle.

The “wash cycle phases” corresponding to the selected wash cycle and the

“wash cycle phase” of the running wash cycle appear in section :B

Main wash

Rinse

Spin + Pump out

References indicate the wash options available (See “Options” section). C

The “Start Delay” symbol , when lit, indicates that the set “delayed start”

value has appeared on the display.

The symbol indicates the possibility of inserting an additional garments

load with the washing program started (See “Adding Garments” section).

The symbol indicates the possibility to silence the key tones

While the mute is active, almost all sounds will be turned o. Only the sound

signals and the alarms remain active, as well as the sound of the end of cycle.

For activate/deactivate the mute press and hold button.

DISPLAY INDICATORS

Failure: Call Service

Refer to Troubleshooting section

Failure: Water lter clogged

Water cannot be drained; water lter might be blocked

Failure: No water

No or not sucient inlet water.

In the event of any failure, refer to the “Troubleshooting” section.

Key Lock

To lock the control panel, press and hold the “Key lock” button for

approximately 3 seconds. The symbol will light up on the display to

indicate that the control panel has been locked (with the exception of the

“ON/OFF“ button). This prevents unintentional changes to programmes,

especially with children near the machine. To unlock the control panel,

press and hold the “Key lock” button for approximately 3 seconds .

Locked door indicator

When lit, the symbol indicates that the door is locked. To prevent any

damage, wait until the symbol turns o before opening the door.

To open the door while a cycle is in progress, press the START/PAUSE

button ; if the symbol is o, the door can be opened.

FIRSTTIME USE

Once the appliance has been installed, and before you use it for the rst

time, run a wash cycle with detergent and no laundry, using the wash

cycle .White (60°)

DAILY USE

Prepare the laundry by following the suggestions appearing under the

“TIPS AND SUGGESTIONS” section.

- Press the ON/OFF button .

- Open the door. Load the laundry while making sure not to exceed the

maximum load quantity indicated in the wash cycle table.

- Pull out the detergent dispenser drawer and pour the detergent into the

relevant compartments, as described in the “DETERGENT DISPENSER

DRAWER” section.

- Close the door.

- The machine automatically displays the default temperature and spin

speed values for the selected cycle, or the most recently used settings if

they are compatible with the selected cycle.

- Select the desired wash cycle.

- Select the desired options.

STARTING CYCLE

- Press the start/pause button.

The machine will lock the door ( symbol on) and the drum will start to

rotate; the door will be unlocked ( symbol OFF) and then locked again

( symbol on) as preparation phase of each washing cycle. The “Clicking”

noise is part of the door locking mechanism. Water will enter the drum

and start the washing phase once the door is locked.

PAUSING A CYCLE

To pause the wash cycle, press the START/PAUSE button again. To start

the wash cycle from the point at which it was interrupted, press the

START/PAUSE button again.

OPENING THE DOOR, IF NECESSARY

Once a cycle starts, the symbol turns on to signal that the door cannot

be opened. While a wash cycle is running, the door remains locked. To

open the door while a cycle is under way, for example, to add or remove

garments, press the START/PAUSE button to pause the cycle. If the

symbol is not lit, the door may be opened. Press the START/PAUSE

button again to continue the cycle.

END

E M

ADDING GARMENTS

An icon on the display will signal when additional garments can be

introduced into the washing machine, without decreasing the washing

performance. To add garments, rst stop the washing machine by pressing

the START/PAUSE button then open the door and insert them.

Press the START/PAUSE button again to restart the wash cycle from

the point at which it was interrupted.

CHANGING A RUNNING WASH CYCLE

To change a wash cycle while it is in progress, pause the washing machine

using the START/PAUSE button, then select the desired cycle and press

the START/PAUSE button again.

! To cancel a cycle that has already begun, press and hold the ON/OFF

button. The cycle will be stopped and the machine will switch o.

AT THE END OF THE WASH CYCLE

This will be indicated by the word on the display; when the “ ”

symbol switches o, the door may be opened. Open the door, unload the

laundry and switch o the machine. If you do not press “ON/OFF” button,

the washing machine will switch o automatically after about a 10 minutes.

OPTIONS

- If the selected option is not compatible with the set wash cycle, the

indicator light will ash accompanied by a buzzer and the option will

not be activated.

- If the selected option is not compatible with another previously

selected option, the indicator light will ash accompanied by a buzzer

and the option will not be activated.

Steam Hygiene

This option enhances washing performance by generating steam during

the wash cycle to remove any bacteria from the bres, which are treated

at the same time. Place the laundry in the drum, choose a compatible

programme and select option Steam Hygiene.

! The steam generated during the operation of the washing machine may

cause the porthole door to become hazy.

Final Care

The washing machine will perform gentle tumbling through slow

rotations of the drum. Final Care option starts after the cycle ends for a

maximum duration of 6h and you can interrupt at any time by pressing

any button on control panel or turning the knob.

Rapid / Green

After pushing the button for the 1st time, option Rapid is selected and the

cycle duration will be reduced.

Otherwise after pushing for the 2nd time, option Green is selected

allowing more energy saving.

Active Care

The detergent, premixed with water, creates an unique emulsion able

to better penetrate the bers of the garments, cleaning stains at even

low temperatures, preserving both colors and fabrics. These results are

obtained also due to the multiple dierent specic movements of the

drum which best take care of the garments.

Powder and liquid detergents are recommended for this option.

Start Delay

To set a delayed start for the selected cycle, press the corresponding

button repeatedly until the desired delay period is reached. When this

option has been activated, the symbol lights up on the display. To

remove the delayed start setting, press the button until “OFF” appears on

the display.

Temperature

Each wash cycle has a pre-dened temperature. To modify the temperature,

press the “Temp.” button. The value will appear on the display.

Spin

Each wash cycle has a pre-dened spin speed. To modify the spin speed,

press the “Spin Speed” button. The value will appear on the display.

DESCALE AND CLEAN PROCEDURE

An icon on the display will regularly (roughly every 50 cycles) remind users

that is time to run a maintenance cycle to clean the washing machine and

combat limescale build-up and bad odours.

To delete the descale alert turn the knob or push any button (including ON/

OFF button).

For optimal maintenance we suggest using WPRO Limescale and grease

remover, according to the instructions shown on the package.

The product can be purchased by contacting the technical assistance service

or through the website www.whirlpool.eu.

Whirlpool declines all liability for any damages to the appliance caused by the

use of other cleaning products for washing machines available on the market.

TIPS AND SUGGESTIONS

Divide the laundry according to:

Type of fabric (cotton, mixed bres, synthetics, wool, garments to be

hand-washed). Colour (separate coloured garments from whites, wash new

coloured garments separately). Delicates (small garments – such as nylon

stockings – and items with hooks – such as bras: insert them in a fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washing machine and

the drum. Check all buttons.

Follow the dosage recommendation / additives

It optimizes the cleaning result, it avoids irritating residues of surplus detergent

in your laundry and it saves money by avoiding waste of surplus detergent

Use low temperature and longer duration

The most ecient programmes in terms of energy consumption are

generally those that perform at lower temperatures and longer duration.

Observe the load sizes

Load your washing machine up to the capacity indicated in the

“PROGRAMME CHART” table to save water and energy.

Noise and remaining moisture content

They are influenced by the spinning speed: the higher the spinning speed in the

spinning phase, the higher the noise and the lower the remaining moisture content.

CARE AND MAINTENANCE

For any cleaning and maintenance, switch o and unplug the washing machine.

Do not use ammable uids to clean the washing machine.

Clean and maintain your washing machine periodically (at least 4 times per year).

Cutting o the water and electricity supplies

Close the water tap after every wash. This will limit wear on the hydraulic

system inside the washing machine and help to prevent leaks.

Unplug the washing machine when cleaning it and during all

maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance can be cleaned using

a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

Remove the dispenser drawer by lifting and pulling it outwards. Wash it

under running water; this procedure should be eected regularly.

Caring for the door and drum

Always leave the porthole door ajar in order to prevent unpleasant odours

from forming.

Cleaning the pump

The washing machine is tted with a self-cleaning pump that does not require

any maintenance. Small items (such as coins or buttons) may sometimes fall

into the protective pre-chamber situated at the base of the pump.

! Make sure that the wash cycle has ended and unplug the appliance.

To access the pre-chamber:

1. remove the covering panel on the front side of the machine by inserting

a screwdriver in the centre and sides of the panel and using it as a lever;

2. place a low and wide container under the water lter in order to collect

the residual water.

3. loosen the drainage pump cover by turning it anti-clockwise: it is

normal for some water to leak out;

4. clean the inside thoroughly;

5. screw the cover back on;

6. put the panel back in place, making sure the hooks slot in place before

pushing the panel onto the appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If it is cracked or broken, it

must be replaced: during wash cycles, the high pressure of the water

could suddenly split the hose open.

! Never use hoses that have already been used.

ANTIMICROBIAL SEAL

The seal around the porthole door is made from a special mixture

ensuring antimicrobial protection, thus reducing bacterial proliferation

up to 99.99%.

The seal contains zinc pyrithione, a biocidal substance which reduces the

proliferation of harmful microbes (*) such as batteries and mould prone to

causing stains, unpleasant odours and product deterioration.

(*) According to tests performed by the University of Perugia, Italy

on: Staphylococcus aureus, Escherichia coll, Pseudomonas aeruginosa,

Candida albicans, Aspergillus niger, Penicillium digitatum

In rare cases an allergic reaction may be caused by prolonged contact between

seal and skin.

ACCESSORIES

Contact our Technical Assistance Service to check whether the following

accessories are available for this washing machine model.

Stacking kit

With this accessory you can secure the tumble dryer to the upper part of

your washing machine to save space and facilitate loading and unloading

of the tumble dryer.

TRANSPORT AND HANDLING

Do not lift the washing machine by gripping it from the upper section.

Unplug the appliance and close the water tap. Check that the door and

detergent dispenser drawer are tightly closed. Detach the lling hose

from the water tap then detach the drain hose. Empty all the water

remaining in the hoses and secure the latter so that they do not get

damaged during transport. Apply the transport bolts back on. Repeat, in

reverse order, the transport bolt removal procedure described in the

“Installation instructions”.

Product specificaties

Merk:	Hotpoint
Categorie:	Wasmachine
Model:	NM11 946 WS A UK N

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint NM11 946 WS A UK N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wasmachine Hotpoint

Hotpoint NF95W IT N Handleiding

16 November 2024

Hotpoint NBT 946 WM A IT Handleiding

16 November 2024

Hotpoint NFR527W Handleiding

16 November 2024

Hotpoint NBT 1048 WD A IT Handleiding

6 Oktober 2024

Hotpoint NBT 108 BLACK IT Handleiding

6 Oktober 2024

Hotpoint NG 847 WM A IT Handleiding

5 September 2024

Hotpoint NR 748G WS A IT Handleiding

5 September 2024

Hotpoint TL R4256BS Handleiding

5 Juli 2024

Hotpoint NLCD 948 WC A \ Handleiding

5 Juli 2024

Hotpoint NDD 9636 BDA EE Handleiding

12 April 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Bosch WGB256040 Handleiding

23 November 2024

Bosch WNG24400IT Handleiding

23 November 2024

Bosch WAN28094 Handleiding

23 November 2024

Electrolux EW7T3722AF Handleiding

23 November 2024

Bosch WGG244120 Handleiding

23 November 2024

Bosch WNG24441 Handleiding

23 November 2024

Bosch WGB254A0IT Handleiding

23 November 2024

Bosch WGG142Z6IT Handleiding

23 November 2024

Bosch WGG142Z8IT Handleiding

23 November 2024

Bosch WGG254Z7IT Handleiding

23 November 2024