Hotpoint HSFE 1B19 S UK N Handleiding

Hotpoint Vaatwasser HSFE 1B19 S UK N

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint HSFE 1B19 S UK N (8 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

1. Upper rack

2. Foldable aps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Cutlery basket

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10. Detergent and Rinse Aid dispensers

11. Rating plate

12. Control panel

0000 000 00000

Service:

1011

1 2 3 4 56 7 8

DAILY REFERENCE

GUIDE

CONTROL PANEL

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

In order to receive a more complete assistance, please

You can download the Safety Instructions and the User

Manual, by visiting our website docs.hotpoint.eu and

following the Instructions on the back of this booklet.

PRODUCT DESCRIPTION

1. On-O/Reset button with indicator light

2. Tablet (Tab) button with indicator light

3. Salt rell indicator light

4. Rinse Aid rell indicator light

5. Program selection knob

6. Delay indicator light

7. Delay button with indicator light

8. Start/Pause button with indicator light / Drain out

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes

and on the machine’s functional components.

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see PRODUCT DESCRIPTION) and must be lled when the SALT REFILL

indicator light in the control panel is lit .

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. Only the rst time you do this: ll the salt

reservoir with water.

3. Position the funnel (see gure) and ll the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can

get into the container during the wash program (this could damage

the water softener beyond repair).

Whenever you need to add salt, it is mandatory to complete

the procedure before the beginning of the washing cycle to avoid

corrosion.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in your

house. This information can be obtained from your local water supplier.

The factory sets the default value for the water hardness:

• Switch on the appliance by pressing the button.ON/OFF

• Switch o the appliance by pressing the button.ON/OFF

• Hold down button START/Pause for 5 seconds.

• Switch on the appliance by pressing the button.ON/OFF

• The ON/OFF LED light will ash as many times as the level that was set.

• Set the desired water hardness level using the PROGRAM SELECTION

knob (see WATER HARDNESS TABLE).

• Switch o the appliance by pressing the button.ON/OFF

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL

indicator light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher

detergent.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

°Clark

English degrees

1 Soft 0 - 6 0 - 10 0 - 7

2 Medium 7 - 11 11 - 20 8 - 14

3 Average 12 - 16 21 - 29 15 - 20

4 Hard 17 - 34 30 - 60 21 - 42

5 Very hard 35 - 50 61 - 90 43 - 62

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser should A

be lled when the indicator light in the control RINSE AID REFILL

panel is lit.

1. Open the dispenser by pressing and pulling up the tab on the lid.B

2. Pour in the rinse aid (max.110 ml), making sure it does not overow

from the dispenser. If this happens, clean the spill immediately with

a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satised with the drying results, you can

adjust the quantity of rinse aid used.

• Switch the dishwasher on using the button.ON/OFF

• Switch it o using the button.ON/OFF

• Press button START/Pause three times.

• Switch it on using the button.ON/OFF

• The START LED light will ash as many times as the level that was set.

• Set the level of rinse aid quantity to be supplied using the PROGRAM

SELECTION knob (see PROGRAMS TABLE).

• Switch it o using the buttonON/OFF

Setting is complete!

If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is specic to the model, please follow instruction

above to check this for your machine

• If you see bluish streaks on the dishes, set a low number (2-3).

• If there are drops of water or limescale marks on the dishes, set a mid-

range number (4-5).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device C.

Introduce the detergent into the dry dispenser D only. Place

the amount of detergent for pre-washing directly inside the tub.

1. When measuring out the detergent

refer to the mentioned earlier

information to add the proper

quantity. Inside the dispenser

D there are indications to help

the detergent dosing.

2. Remove detergent residues from

the edges of the dispenser and close

the cover until it clicks.

3. Close the lid of the detergent

dispenser by pulling it up until

the closing device is secured

in place.

The detergent dispenser automatically opens up at the right time

according to the program.

If all-in-one detergents are used, we recommend using the TABLET

button, because it adjusts the program so that the best washing and

drying results are always achieved.

Usage of detergent not designed for dishwashers may cause

malfunction or damage to the appliance.

PROGRAMS TABLE

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

1 ECO

Eco programme is suitable to clean normally soiled tableware, that

for this use, it is the most ecient programme in terms of its combined

energy and water consumption, and that it is used to assess compliance

with the EU Ecodesign legislation.

2 INTENSIVE

Program recommended for heavily soiled crockery, especially suitable

for pans and saucepans (not to be used for delicate items).

3 MIXED

Mixed soil. For normally soiled dishes with dried food residues.

4 DELICATES

Program for delicate items, which are more sensitive to high

temperatures, for example glasses and cups.

5 RAPID 30’

Program to be used for half load of lightly-soiled dishes with no dried

food residues Does not have drying phase.

6 HALF LOAD

Ideal for washing a half load of lightly or normally soiled crockery.

7 SOAK

Use to refresh crockery planned to be washed later. No detergent to be

used with this program.

Notes:

Please note that cycle is dedicated for lightly soiled dishes.Rapid 30’

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Note for Test Laboratories:

For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com.

Pre-treatment of the dishes is not needed before any of the programs.usly.

*) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature

and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options

and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Program

Drying phase

Available options *)

Duration of wash

program

(h:min)**)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

1. Eco 50° 4:00 11.5 0.84

2. Intensive 65° 2:30 15.0 1.50

3. Mixed 55° 2:30 15.0 1.30

4. Delicates 45° 1:40 11.5 1.00

5. Rapid 30’ 50° - 0:30 8.5 0.50

6. Half Load 50° 1:15 11.0 0.90

7. Soak - - 0:10 4.5 0.01

Product specificaties

Merk:	Hotpoint
Categorie:	Vaatwasser
Model:	HSFE 1B19 S UK N
Apparaatplaatsing:	Vrijstaand
Soort bediening:	Draaiknop
Gewicht:	34900 g
Breedte:	450 mm
Diepte:	590 mm
Hoogte:	850 mm
Netbelasting:	1900 W
Aantal couverts:	10 couverts
Deurkleur:	Zilver
Snoerlengte:	1.3 m
Uitgestelde start timer:	Ja
Duur cyclus:	240 min
Geluidsniveau:	49 dB
Energie-efficiëntieklasse:	F
Gewicht verpakking:	36700 g
Installatie compartiment breedte:	600 mm
Installatie compartiment diepte:	590 mm
Waterconsumptie per cyclus:	11.5 l
Stroom:	13 A
Installatie compartiment hoogte (min):	820 mm
Zelfreinigend:	Ja
Geluidsemissieklasse:	C
Energieverbruik per 100 cycli:	84 kWu
Verstelbare voeten:	Ja
Productafmeting:	Slimline (45 cm)
Kleur bedieningspaneel:	Zilver
Bestek compartiment type:	Mand
Zout indicator:	Ja
Glansmiddel indicator:	Ja
Half-geladen:	Ja
Afwasprogramma's:	Auto, Dual Pro Wash, Eco, Glass/delicate, Quick, Silent, Soak
Lengte afvoerslang:	1.5 m
Lengte watertoevoerslang:	1.55 m
Installatie compartiment hoogte (max):	900 mm
Temperatuur (max):	- °C
Onderste korf:	Vast
Watertoevoer:	Koud
Manden verstelbare plaatsing:	Lower, Upper
Stroomverbruik (indien uit):	- W
AC-ingangsspanning:	230 - 240 V
AC-ingangsfrequentie:	50 Hz
Energie-efficiëntieschaal:	A tot G