Hotpoint HDA3700GWW Handleiding

Hotpoint Wasmachine HDA3700GWW

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint HDA3700GWW (9 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 66 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/9
GE Consumer & Industrial
Appliances
I
n
s
t
a
l
l
t
i
o
n
I
n
s
t
r
u
c
t
i
o
n
s
Junction Box Cov
er
Suppl
ied Parts:
#10
Hex-Head Screw 1/2"
Long
Junct
ion Box Cover
Within this user bag, you will find a junction
box cover and a #10 hex head screw used
to attach the junction box cover to the
bottom bracket or front brace (depending
on the model). The #10 hex-head screw
is packaged in a small bag within the
user bag. Use these parts when making
electrical
connections.
© 200
6
General Electric Company
Pub. No.
49-55020
Part
No
.
1
65D4700P340
ND
0
6
C
-1
6
90
(4/06)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
THE JUNCTION BOX COVER AND SCREW
MUST BE USED DURING THE ELECTRICAL
CONNECTION STEPS TO AVOID THE RISK OF
FIRE OR ELECTRIC SHOCK. SEE INSTALLATION
INSTRUCTIONS.
WARNING
Installation instructions
for your new
• Before you begin—Read these instructions completely and carefully.
• IMPORTANT–Save these instructions for local inspector’s use.
• IMPORTANT–OBSERVE ALL GOVERNING CODES AND ORDINANCES.
• Note to Installer–Be sure to leave these instructions with the Consumer.
• Note to Consumer–Keep these instructions with your Owners Manual for future reference.
Built-In
Dishwasher
If you have a question concerning the installation of this
product, call the GE Answer Center Consumer Information
Service at 800.626.2000, 24 hours a day, 7 days a week.
If you received a damaged dishwasher,
you should immediately contact your
dealer or builder.
Installation of this dishwasher requires basic mechanical and
electrical skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation is not
covered under the GE Appliance Warranty. See the back
cover of the Owners Manual for warranty information.
The dishwasher MUST be installed to allow for future removal
from the enclosure if service is required.
MATERIALS YOU WILL NEED:
Materials required:
l 90° elbow
(3/8" NPT external thread on one end and
opposite end sized to fit water supply)
l Thread seal tape
l UL Listed Wire nuts (3)
For new installations only:
l Air gap for drain hose, if required
l Waste tee for house plumbing, if applicable
l Electrical cable or power cord, if applicable
l Screw type hose clamps
l Strain relief for electrical connection
l Hand shut-off valve (recommended)
l Water line 3/8" min. copper or 1/2" min. plastic
l Coupler for extending drain line, if applicable
Electrical Cable
or Power Cord 90° Elbow
Strain Relief
Hot Water Line
Thread Seal
Tape
Screw Type Clamps
Wire Nuts
Air
Gap Waste
Tee
Shut-Off
Valve
Flashlight
Flat Blade Screwdriver
Drill
and Bits
Measuring Tape Level
Phillips Head
Screwdriver
Tubing
Cutter
Square
Hole
Saw Set
TOOLS YOU WILL NEED:
Tools required:
l Phillips head and flat blade screwdrivers
l Adjustable wrench (6")
l Level
l Carpenters square
l Measuring tape
l Safety glasses
l Flashlight
For new installations only:
l Tubing cutter
l Drill and appropriate bits
l Hole saw set
Adjustable
Wrench
Safety Glasses
CAUTION:
PARTS SUPPLIED FOR INSTALLATION:
l Two Phillips head countertop mounting screws taped to dishwasher
Coupler
PREPARE DISHWASHER ENCLOSURE
• The rough cabinet opening must have a minimum width and
depth of 24", and approximately 34-1/2" high from floor to
underside of the countertop. Figure A
• The back wall should be free of pipes or wires. Figure A
• Adjacent cabinets should be square and plumb to ensure a
good fit. Figure A
• For corner installation, allow 2" min. clearance between
dishwasher and adjacent cabinet or wall or other
appliances. Figure B
2
• Make sure the floor is level inside the opening and even
with the finished floor of the kitchen.
• The dishwasher must be installed no more than 10 feet from
sink for proper drainage.
• This dishwasher must be fully enclosed on the top, sides
and back.
• The dishwasher must not support any part of the enclosure.
Figure B
CAUTION
An air gap MUST BE USED if the drain hose is connected to
waste tee or disposer lower than 18" above the floor level.
Failure to provide the proper drain connection height with air
gap or 32" minimum, high drain loop will result in improper
draining of the dishwasher which may cause damage.
PREPARE DRAIN PLUMBING
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Dishwasher drain hose must not exceed 10 feet in length for
proper drainage.
• Dishwasher must be connected to waste line with an air
gap (not supplied) or 32" minimum, high drain loop depend-
ing on local codes and ordinances to prevent back flow into
the dishwasher.
• Air gap must be used if waste tee or disposer connection is
less than 18 inches above floor to prevent siphoning.
DRAIN PREPARATION
The type of drain installation depends on answers to the
following questions:
l Do local codes or ordinances require an air gap?
l Will waste tee or disposer connection be less than 18"
above floor?
l Will installation have a drain loop less than 32" above floor?
If the answer to of the 3 questions above is ANY YES, Method
1 MUST be used. Otherwise either Method 1 or Method 2 may
be used. Figure C or Figure D.
METHOD 1–Air Gap with Waste Tee or Disposer
Figure A
Install waste tee or disposer and air gap according to
manufacturer’s instructions.
CABINET PREPARATION
Drill 1-1/2" inch diameter hole in the cabinet wall within the
shaded area shown in Figure A for the drain hose. Make sure
there are no sharp edges. Drain hose will be passed through
this hole and connected to the drain in a later step.
Disposer Installation
METHOD 2–High Drain with Waste Tee or Disposer
Provide a method to attach drain hose to underside of
countertop. Attachment will be made in a later step.
Waste Tee Installation Figure C
Waste Tee Installation Disposer Installation
Figure D
25"
Countertop
Dishwasher
Clearance for Door
Opening 2" Minimum
24"
Min.
This Wall Area
must be Free of
Pipes or wires
Plumbing and Electric Service
Must Enter Inside This Area
34-1/2" 1/4"±
Underside of
Countertop
to Floor
4"
24"
Min.
6"
5" 5"
4"
Cabinets Square
and Plumb
32"
Min.
18"
Min.
32"
Min.
18"
Min.

Product specificaties

Merk: Hotpoint
Categorie: Wasmachine
Model: HDA3700GWW

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint HDA3700GWW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wasmachine Hotpoint

Hotpoint

Hotpoint H6 08 GPOWER IT Handleiding

2 December 2024
Hotpoint

Hotpoint NR 849G WS A IT Handleiding

2 December 2024
Hotpoint

Hotpoint NG98W IT Handleiding

2 December 2024
Hotpoint

Hotpoint NF746WK IT Handleiding

2 December 2024
Hotpoint

Hotpoint H7 99 GPOWER IT Handleiding

2 December 2024
Hotpoint

Hotpoint NBT 116 BLACK IT Handleiding

2 December 2024
Hotpoint

Hotpoint NLCD 946 WC A EU N Handleiding

2 December 2024
Hotpoint

Hotpoint BI WMHG 81485 EU Handleiding

2 December 2024
Hotpoint

Hotpoint BI WDHG 861485 EU Handleiding

2 December 2024
Hotpoint

Hotpoint NM11 846 WS A EU N Handleiding

2 December 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Asko

Asko w 6362 l tit Handleiding

5 December 2024
Asko

Asko W2084.W-2 Handleiding

5 December 2024
Bauknecht

Bauknecht BPW 1014 A Handleiding

21 December 2024
Asko

Asko w 6362lt Handleiding

5 December 2024
Svan

Svan SL8201DD Handleiding

21 December 2024
Svan

Svan SLI8200D Handleiding

21 December 2024
Svan

Svan SL9401AIDB Handleiding

21 December 2024
Svan

Svan SL7201DD Handleiding

21 December 2024
Electrolux

Electrolux EWD8462OBI Handleiding

20 December 2024
Svan

Svan SL6001DD Handleiding

20 December 2024