Hotpoint H6 W845WB UK Handleiding

Hotpoint Wasmachine H6 W845WB UK

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint H6 W845WB UK (8 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Quick Guide

Before using the appliance carefully read the Health and Safety guide.

Before using the machine, it is imperative that the transport bolts are removed. For more

detailed instructions on how to remove them, see the Installation Guide.

CONTROL PANEL

WASH CYCLE TABLE

1. RAPID button

2. SCROLL UP / SCROLL DOWN buttons

3. ON/OFF button

4. STEAM FINISH button and indicator light

5. START/PAUSE button

6. CONFIRM / KEY LOCK button

7. START DELAY button

8. SPIN button

9. TEMPERATURE button

10. CYCLE OPTION MENU

/ SETTINGS MENU button

11. STEAM HYGIENE button

12. WASH CYCLE SELECTOR KNOB

THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.

To receive more comprehensive assistance, register the

appliance on

www.hotpoint.eu/register

For all testing institutes:

2) Long cotton cycle: set wash cycle “Cotton” with a temperature of 40°C.

3) Long synthetics cycle: set wash cycle “Synthetics” with a temperature of 40°C.

* By selecting the “Spin & Drain” cycle and excluding the spin cycle, the washing machine will

drain only.

** The duration of the wash cycles can be checked on the display.

***

After programme end and spinning with maximum selectable spin speed, in default

programme setting.

The cycle duration indicated on the display or instruction manual is an estimate based on

standard conditions. The actual duration may vary in relation to several factors, such as the

temperature and pressure of the incoming water, ambient temperature, amount of detergent,

load quantity and type, load balancing and any additional options selected.The values given

for programmes other than the Eco 40-60 programme are indicative only.

1) Eco 40-60 - Test wash cycle in compliance with EU Ecodesign regulation 2019/2014. The most efficient

programme in terms of energy and water consumption for washing normally soiled cotton laundry.

Note: spin speed values shown on the display can slightly differs from the values stated in the table.

! Selecting “More cycles” on the control dial gives you access to extra wash cycles shown in

the table above.

12 3

5678911 10

DISPLAY

Maximum load 8 kg

Power input in o mode 0.5 W / in left-on mode 8 W

Detergents and

Additives

Recommended

detergent

Residual dampness

% (***)

Energy consumption

kWh

Total water l

Laundry

temperature °C

Wash cycle

Temperature Max.

spin speed

(rpm)

Max.

load

(kg)

Duration

(h : m)

Pre-

wash Wash Fabric

softener

Powder Liquid

Setting Range

Anti Stain 40°C - 40°C 1400 8,0 **   –   – – – – –

Mixed Extra Silence 40°C - 40°C 600 4,0 **   –  –– – – 

Mixed 40°C - 40°C 1400 8,0 **   –  –– – – 

Cotton (2) 40°C - 90°C 1400 8,0 3:10        49 0,87 68 45

Synthetics (3) 40°C - 60°C 1200 4,5 2:45        35 0,54 74 43

Delicates 30°C - 30°C - 1,0 **   –  –– – – 

Wool 30°C - 30°C 600 2,0 ** – –  –– – – 

Spin & Drain * – – 1400 8,0 ** – – – – – – – – – – –

More Cycles

• Rinse & Spin – – 1400 8,0 ** – – – – – – – – –

• Multi Color 20 °C - 20 °C 1400 8,0 **   –  –– – – –

• Bed & Bath 60°C - 60°C 1400 8,0 **   –    – – – –

• Duvet 30°C - 30°C 1000 3,5 **   –  –– – – –

• Silk & Curtains 30°C - 30°C – 1,0 **   –  –– – – –

• Baby 40°C - 40°C 800 4,0 **   –  –– – – –

• Cuddly Toys 30°C - 30°C – 1,0 **   –– – – – – –

• Pets Stu 40°C - 40°C 600 2,0 **   –  –– – – –

• Shirts 40°C - 40°C 600 3,0 **   –  –– – – –

• Jeans 40°C - 40°C 800 2,0 **   –  –– – – –

20°C 20 °C - 20 °C 1400 8,0 1:50   –  –55 0,14 78 22

Eco 40-60 40 °C 40°C

1351 8,0 3:35 – –    53 0,75 62 33

1351 4,0 2:45 – –    53 0,50 42 26

1351 2,0 2:30 – –    53 0,35 37 24

Anti Allergy 60°C 40°C -

60°C 1400 5,0 **   –    – – – –

Full Load 45 min. 40°C - 40°C 1200 8,0 **   –    – – – –

Rapid 30 min 30°C - 30°C 800 4,5 0:30   –  –71 0,18 37 27

Steam Refresh 20 min – – – 2,0 ** – – – – – – – – – – –

  Required dosage Optional dosage

WASH CYCLES

Follow the instructions on the symbols of the garment’s wash care

label. The value indicated in the symbol is the maximum

recommended temperature for washing the garment.

Anti Stain

The programme is suitable to heavily-soiled garments with resistant

colours. It ensures a washing class that is higher than the standard class.

When running the programme, do not mix garments of dierent colours.

We recommend the use of powder detergent. Pre-treatment with special

additives is recommended if there are obstinate stains.

Mixed Extra Silence

Discover the silence: this programme runs silently for the entire cycle, spin

phase included. Designed for a half load and mixed bres (cotton &

synthetics), with the spin speed adjusted for a more delicate clean. After

the cycle, Steam Finish option will start automatically, for 100% freshness

and total peace of mind.

Mixed

For washing lightly to normally soiled resilient garments in cotton, linen,

synthetic bres and mixed bres.

Cotton

Normally to heavily soiled and robust cottons .

Synthetics

Suitable for washing moderately soiled garments made of synthetic bres

(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.

Delicates

For washing very delicate garments. It is advisable to turn the garments

inside out before washing them. For best results, use liquid detergent on

delicate garments.

Wool

All wool garments can be washed using programme‚ “Wool“ even those

carrying the “hand-wash only “ label. For best results, use special

detergents and do not exceed max kg declaration of laundry.

Spin & Drain

Spins the load then empties the water. For resilient garments. If you

exclude the spin cycle, the machine will drain only.

More Cycles

• Rinse & Spin

Rinses and then spins. For resilient garments.

• Multi Color

This cycle is suitable for washing multi-coloured items, or various

dierent colours together. The programme is studied to guarantee

colour care, working at 20°C with the same performance as 40°C. It is

suggested to use a detergent for coloured clothes and for low

temperatures.

! It’s always suggested to separate clothes that are faded and new

coloured clothes, being washed for the rst time.

• Bed & Bath

For washing bed linen and towels in a single cycle. It optimises the use

of fabric softener and allows for saving time and electricity. We

recommend the use of powder detergent.

• Duvet

Designed for washing eiderdown padded items such as double or

single duvets, cushions and anoraks. It is recommended to load such

padded items in the drum with the edges folded inwards and not to

exceed ¾ of the drum’s volume. For optimal washing, we recommend

using a liquid detergent.

• Silk & Curtains

Use the special wash cycle to wash all silk garments or curtains. We

recommend the use of special detergent which has been designed to

wash delicate clothes.

For washing curtains, fold and place them in a pillow case or mesh bag.

• Baby

Use the special wash cycle the remove the soiling typically caused by

babies, while removing all traces of detergent from nappies in order to

prevent the delicate skin of babies from suering allergic reactions.

The cycle has been designed to reduce the amount of bacteria by

using a greater quantity of water and optimising the eect of special

disinfecting additives added to the detergent.

• Cuddly toys

Specic programme for removing dust and washing cuddly toys.

• Pets Stu

Perfect for removing animal hair from pets bedding and items.

• Jeans

Turn garments inside-out before washing and use a liquid detergent.

• Shirts

Use the special wash cycle to wash shirts in dierent fabrics and

colours to guarantee they receive the best possible care.

20°C

For washing lightly soiled cotton garments, at a temperature of 20 °C.

Eco 40-60

For washing normally soiled cotton garments declared to be washable

at 40 °C or 60 °C, together in the same cycle. This is the standard cotton

programme and the most ecient in terms of water and energy

consumption.

Anti Allergy

Suitable for removing major allergens such as pollen, mites and cat or dog

hair, thanks to a high-temperature technology and extra rinses.

! This cycle is working at 60°C temperature for at least 30 minutes.

Full Load 45 min.

Suitable for washing a full load of cotton clothes moderately soiled in 45

minutes.

Rapid 30 min

For washing lightly soiled garments quickly. This cycle lasts only 30

minutes, saving time and energy.

Steam Refresh 20 min

The garments will be damp once the cycle is completed, so we

recommend hanging them to dry (2 kg, roughly 3 items). This programme

refreshes garments by removing bad odours and relaxing the bres. Insert

dry items only (that are not dirty) and select programme “Steam Refresh”.

Garments will be a little damp at the end of the cycle and can be worn

after a few minutes. The “Steam Refresh” programme makes ironing easier.

! Do not add softeners or detergents.

! Not recommended for wool or silk garments.

DISPLAY

The display is useful when programming the washing machine and

provides plenty of information.

COTTON

--:--

1:40

140040°

By pressing the and buttons, it is possible to select the desired

option and conrm it with the button.

The rst time the machine is switched on, you will be asked to select the

language and the display will automatically display the language selection

menu.

To select the desired language, press the and buttons; to conrm

the selection, press the button.

Area A will display the following: the icon and selected washing programme,

the washing phases and the time remaining to the end of the wash cycle.

Area B will display: the selected options, the energy and water consumption

for the chosen cycle and the button lock symbol.

Area C will display the default temperature value on the basis of the set

programme; if the programme does not include the setting of the

temperature, the area will display the “ ” symbol.-- °

Area D will display the default spin cycle speed on the basis of the set

programme; if the programme does not include the setting of the spin

cycle, the area will display the “ ” symbol.--

Area E will display the time remaining to the start of the selected

programme if the DELAYED START function was set.

Pressing button allows for accessing the menu from which to set F

additional washing options.

Pressing and holding button for 3 seconds allows for accessing the F

settings menu:

- Language: by pressing the and buttons, the user can select the

desired language and conrm it with the button.

- Sound: by pressing the and buttons, the user can activate or

deactivate the sound of the buttons and conrm it with the button.

1. Top

2. Detergent dispenser drawer

3. Control panel

4. Handle

5. Porthole door

6. Pump Filter / Emergency drain hose

(behind cover ap)

7. Adjustable feet (4)

DETERGENT DISPENSER DRAWER

Handle the dispenser with care. Avoid pulling or pushing hard the

dispenser during opening and closing.

compartment 1: Pre-wash detergent

(powder)

compartment 2: Detergent for the wash

cycle (powder or liquid)

compartment 3: Additives (fabric

softeners, etc.)

The fabric softener should not overow the grid.

! Use powder detergent for white cotton

garments, for pre-washing, and for washing at

temperatures over 60°C.

! Follow the instructions given on the detergent

packaging.

PRODUCT DESCRIPTION

- Display brightness: by pressing the and buttons, the user can

select the type of display brightness and conrm it with the button.

- Restoring the factory settings: pressing and holding the button for 2

seconds restores the factory settings.

! During a wash cycle if the user does not interact with the display for 5

minutes, the SCREEN SAVER will activate. To return to the previous window,

simply press any button.

DISPLAY INDICATORS

Failure: Call Service

Refer to Troubleshooting section

Failure: Drain pump lter clogged

Water cannot be drained; drain pump lter might be blocked

Failure: No water

No or not sucient inlet water.

In the event of any failure, refer to the “Troubleshooting” section.

Key Lock

To activate the control panel lock, press and hold the button for

roughly 3 seconds. When the display visualises “KEY LOCK”, the control

panel is locked (except for the ON/OFF button ). This will prevent

accidental modications to wash cycles, especially when children are at

home. To deactivate the control panel lock, press and hold the

button for approximately 3 seconds.

Locked door indicator

When lit, the symbol indicates that the door is locked. To prevent any

damage, wait until the symbol turns o before opening the door.

To open the door while a cycle is in progress, press the START/PAUSE

button ; if the symbol is o, the door can be opened.

FIRSTTIME USE

Once the appliance has been installed, and before you use it for the rst

time, run a wash cycle with detergent and no laundry, using the wash

cycle ) without option Prewash selected.Cotton (60°

DAILY USE

Prepare the laundry by following the suggestions appearing under the

“TIPS AND SUGGESTIONS” section.

- Press the ON/OFF button ; “HOTPOINT” will appear on the display.

- Open the door. Load the laundry while making sure not to exceed the

maximum load quantity indicated in the wash cycle table.

- Push to open the detergent dispenser drawer and pour the detergent

into the relevant compartments, as described in the “DETERGENT

DISPENSER DRAWER” section.

- Close the door.

- The machine automatically selects the default temperature and spin

speed set for the selected wash cycle.

- Select the desired wash cycle.

- Select the desired options.

- Press the START/PAUSE button to start the wash cycle; the door will

lock ( symbol on). After this operation will start the Sensing routine.

PAUSING A CYCLE

To pause the wash cycle, press the START/PAUSE button again. To start

the wash cycle from the point at which it was interrupted, press the

START/PAUSE button again.

OPENING THE DOOR, IF NECESSARY

Once a cycle starts, the symbol turns on to signal that the door cannot

be opened. While a wash cycle is running, the door remains locked. To

open the door while a cycle is under way, for example, to add or remove

garments, press the START/PAUSE button to pause the cycle. If the

symbol is not lit, the door may be opened. Press the START/PAUSE

button again to continue the cycle. After this operation will start the

Sensing routine.

STOP&ADD

An icon on the display will signal when additional garments can be

introduced into the washing machine, without decreasing the washing

performance. To add garments, rst stop the washing machine by

pressing the START/PAUSE button then open the door and insert

them.

Press the START/PAUSE button again to restart the wash cycle from

the point at which it was interrupted.

CHANGING A RUNNING WASH CYCLE

To change a wash cycle while it is in progress, pause the washing machine

using the START/PAUSE button, then select the desired cycle and press

the START/PAUSE button again.

! To cancel a cycle that has already begun, press and hold for a few

seconds the ON/OFF button. If water is present then drain function will

start. The cycle will be stopped and the machine will switch o.

AT THE END OF THE WASH CYCLE

This will be indicated by the word “ ” on the display; when the CYCLE END

symbol switches o, the door may be opened. Open the door, unload the

laundry and switch o the machine. If you do not press ON/OFF button,

the washing machine will switch o automatically after about 10 minutes.

OPTIONS

- If the selected option is incompatible with the set wash cycle or with

another previously selected option, in the menu the name of

incompatible option is represented in grey color and the wording “Not

available” will appear on the display, accompanied by a buzzer, the

option will not be activated.

Steam Finish

100% freshness with Steam: Steam Finish option is designed to keep your

garments fresh up to 6 hours after the cycle is over.

Innovative Steam Finish system takes care of your garments inside the

washing machine with delicate steaming and tumbling action (tested by

SSOG lab). Steam Finish system gently massages the laundry with regular

slow movements alternated with steam actions - letting air circulate

inside the bers to keep garments fresh and prevent bad odours. Steam

Finish treatment leaves truly fresher clothes and peace of mind - even

hours after the end of the cycle. Steam Finish treatment inhibits the

proliferation of the main bad odour sources (inside the washing machine)

up to 6 hours after the washing ends. Not compatible with programmes

designed for delicate garments and duvets.

Rapid

Select this option to reduce the cycle time. This cycle is suggested for

washing light soiled clothes.

Steam Hygiene

This option enhances washing performance by generating steam during

the wash cycle to remove any bacteria from the bres, which are treated

at the same time. Place the laundry in the drum, choose a compatible

programme and select option Steam Hygiene.

! The steam generated during the operation of the washing machine may

cause the porthole door to become hazy.

Easy Iron

By selecting this function, the wash and the spin cycles will be modied in

order to reduce the formation of creases.

Multi Rinse

By selecting this option, the eciency of the rinse is increased and optimal

detergent removal is guaranteed. It is particularly useful for sensitive skin.

Press the button once, two or three times to select an additional 1, 2 or 3

rinses after the standard cycle rinse and remove all traces of detergent.

Press the button again to go back to the “Normal rinse” rinse type.

Cold Wash

This option saves energy by not heating the water used to wash your

laundry – an advantage both to the environment and to your energy bill.

Instead, intensied wash action and water optimisation ensure great

wash results in the same average time of a standard cycle.

For the best washing results we recommend the usage of a liquid

detergent.

Prewash

Allows you to perform a prewash.

Start Delay

To set a delayed start for the selected cycle, press the corresponding

button repeatedly until the desired delay period is reached. When this

option has been activated, the selected values of delay start will appear

on the display. To remove the delayed start setting, press the button until

“--:--” appears on the display.

Temperature

Each wash cycle has a pre-dened temperature. To modify the temperature,

press the “ ” button. The value will appear on the display.

Spin

Each wash cycle has a pre-dened spin speed. To modify the spin speed,

press the button. The value will appear on the display.“ ”

DESCALE AND CLEAN PROCEDURE

Reminder on the display will regularly (roughly every 50 cycles) remind

users that is time to run a maintenance cycle to clean the washing machine

and combat limescale build-up and bad odours.

For optimal maintenance we suggest to run empty cycle “Cotton” at minimum

60°C without PreWash and using WPRO Limescale and grease remover.

The product can be purchased by contacting the technical assistance service

or through the website www.whirlpool.eu.

Whirlpool declines all liability for any damages to the appliance caused by the

use of other cleaning products for washing machines available on the market.

To delete the descale alert turn the knob or push any button (including

ON/OFF button).

TIPS AND SUGGESTIONS

Divide the laundry according to:

Type of fabric (cotton, mixed bres, synthetics, wool, garments to be

hand-washed). Colour (separate coloured garments from whites, wash

new coloured garments separately). Delicates (small garments – such as

nylon stockings – and items with hooks – such as bras: insert them in a

fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washing machine and

the drum. Check all buttons.

Follow the dosage recommendation / additives

It optimizes the cleaning result, it avoids irritating residues of surplus

detergent in your laundry and it saves money by avoiding waste of surplus

detergent

Use low temperature and longer duration

The most ecient programmes in terms of energy consumption are

generally those that perform at lower temperatures and longer duration.

Observe the load sizes

Load your washing machine up to the capacity indicated in the

“PROGRAMME CHART” table to save water and energy.

Noise and remaining moisture content

They are inuenced by the spinning speed: the higher the spinning speed

in the spinning phase, the higher the noise and the lower the remaining

Product specificaties

Merk:	Hotpoint
Categorie:	Wasmachine
Model:	H6 W845WB UK

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint H6 W845WB UK stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wasmachine Hotpoint

Hotpoint H6 08 GPOWER IT Handleiding

2 December 2024

Hotpoint NR 849G WS A IT Handleiding

2 December 2024

Hotpoint NG98W IT Handleiding

2 December 2024

Hotpoint NF746WK IT Handleiding

2 December 2024

Hotpoint H7 99 GPOWER IT Handleiding

2 December 2024

Hotpoint NBT 116 BLACK IT Handleiding

2 December 2024

Hotpoint NLCD 946 WC A EU N Handleiding

2 December 2024

Hotpoint BI WMHG 81485 EU Handleiding

2 December 2024

Hotpoint BI WDHG 861485 EU Handleiding

2 December 2024

Hotpoint NM11 846 WS A EU N Handleiding

2 December 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Asko w 6362 l tit Handleiding

5 December 2024

Asko W2084.W-2 Handleiding

5 December 2024

Bauknecht BPW 1014 A Handleiding

21 December 2024

Asko w 6362lt Handleiding

5 December 2024

Svan SL8201DD Handleiding

21 December 2024

Svan SLI8200D Handleiding

21 December 2024

Svan SL9401AIDB Handleiding

21 December 2024

Svan SL7201DD Handleiding

21 December 2024

Electrolux EWD8462OBI Handleiding

20 December 2024

Svan SL6001DD Handleiding

20 December 2024