Hotpoint FMF 923 Handleiding

Hotpoint Wasmachine FMF 923

Lees hieronder de đź“– handleiding in het Nederlandse voor Hotpoint FMF 923 (60 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/60
1
GB
WASHING MACHINE
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash option
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
FMF 923
Instructions for use
English,1
GB
PT
PortuguĂŞs,49
ES
Español,37
IT
Italiano,25
FR
Français,13
2
GB
Installation
! This instruction manual should be kept in a
safe place for future reference. If the washing
machine is sold, transferred or moved, make
sure that the instruction manual remains with
the machine so that the new owner is able to
familiarise himself/herself with its operation
and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance ( ).see figure
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine
needs to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing
machine on a flat
sturdy floor, without
resting it up against
walls, furniture
cabinets or anything
else.
2. If the floor is not perfectly level, compensate
for any unevenness by tightening or loosening
the adjustable front feet ( ); the angle see figure
of inclination, measured in relation to the
worktop, must not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge
of a basin, sink or
tub, fastening the
duct supplied to
the tap ( ). see figure
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• the socket is earthed and complies with all
applicable laws;
• the socket is able to withstand the
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
• the power supply voltage falls within the
values indicated in the Technical data table
( );see opposite
• the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is
extremely dangerous to leave the appliance
exposed to rain, storms and other weather
conditions.
65 - 100 cm
! When the washing machine has been
installed, the electricity socket must remain
within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle number auto clean (see “Cleaning
the washing machine”).
Technical data
Model FMF 923
Dimensions width 59.5 cm
height 85 cm
depth 60.5 cm
Capacity from 1 to 9 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed up to 1200 rotations per
minute
Test wash
cycles in
accordan-
ce with
directives
1061/2010
1015/2010
programme 4
;
Cotton Standard 60°C.
programme 5
;
Cotton Standard 40°C.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU

Product specificaties

Merk: Hotpoint
Categorie: Wasmachine
Model: FMF 923

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint FMF 923 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wasmachine Hotpoint

Hotpoint

Hotpoint NF95W IT N Handleiding

16 November 2024
Hotpoint

Hotpoint NBT 946 WM A IT Handleiding

16 November 2024
Hotpoint

Hotpoint NFR527W Handleiding

16 November 2024
Hotpoint

Hotpoint NBT 1048 WD A IT Handleiding

6 Oktober 2024
Hotpoint

Hotpoint NBT 108 BLACK IT Handleiding

6 Oktober 2024
Hotpoint

Hotpoint NG 847 WM A IT Handleiding

5 September 2024
Hotpoint

Hotpoint NR 748G WS A IT Handleiding

5 September 2024
Hotpoint

Hotpoint TL R4256BS Handleiding

5 Juli 2024
Hotpoint

Hotpoint NLCD 948 WC A \ Handleiding

5 Juli 2024
Hotpoint

Hotpoint NDD 9636 BDA EE Handleiding

12 April 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Otsein

Otsein LB LTO129A Handleiding

21 November 2024
Otsein

Otsein LB LTO109A Handleiding

21 November 2024
Otsein-Hoover

Otsein-Hoover LB HV16ESALU Handleiding

21 November 2024
Sangiorgio

Sangiorgio ST6512EL Handleiding

21 November 2024
Sangiorgio

Sangiorgio FS614D9 Handleiding

21 November 2024
Sangiorgio

Sangiorgio PROGETTO F4 Handleiding

21 November 2024
Sangiorgio

Sangiorgio SG710 Handleiding

21 November 2024
Sangiorgio

Sangiorgio F814DIBC Handleiding

21 November 2024
Sangiorgio

Sangiorgio F812D Handleiding

21 November 2024
Sangiorgio

Sangiorgio F812L Handleiding

21 November 2024