Hotpoint BS43B Handleiding

Hotpoint Oven BS43B

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint BS43B (12 pagina's) in de categorie Oven. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Operating Instructions

Contents

Installation, 2

Positioning

Electrical connection, 3

Data plate

Description of the appliance, 4

Overall view

Control panel

Start-up an use,d 5

Starting the oven

The electronic cooking progra er,mm 6

Cooking modes, 7-8

Cooking modes

Practical cooking advice

Cooking advice table

Precautions and tips, 9-10

General safety

Disposal

Respecting and conserving the environment

Maintenance an care,d 10

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

After Sales Service, 11

Guarantee, 12

BS43W/1

BS43K/1

BS43B/1

English,1

OVEN

595 mm.

24 mm.

545 mm.

5 mm.

567 mm.

23 mm.

593 mm.

45 mm.

558 mm.

547

mm. min .

Installation

560 mm.

45 mm.

 Before you operate yuor new Hotpoint Single Oven,

please read these instructions fully. They contain

important information for safe use, for installation and

for care of the appliance.

 Please keep these operating instructions for future

reference. Pass them on to possible new owners of

the appliance.

 Keep packaging material out of the reach of

children.It can become a choking or suffocation

hazard. see Precautions and tips).

Positioning

! The appliance must be installed by a qualified

person in compliance with the instructions provided.

Incorrect installation may cause harm to persons,

animals or may damage property.

F itting the appliance

Use the appropriate cabinet to ensure that the

appliance functions properly.

 The panels adjacent to the oven must be made of

heat-resistant material.

 Cabinets with a veneer exterior must be assembled

with glues which can withstand temperatures of up

to 100°C.

 To install the oven under the counter (see diagram)

and in a kitchen unit , the cabinet must have the

following dimensions:

! The appliance must not come into contact with

electrical parts once it has been installed.

The consumption indications on the data plate have

been calculated for this type of installation.

Ventilation

To ensure good ventilation, the back panel of the

cabinet must be removed. It is advisable to install the

oven so that it rests on two strips of wood, or on a

completely flat surface with an opening of at least 45 x

560 mm (see diagrams).

Centring and fastening

Position the 4 tabs on the side of the oven according

to the 4 holes of the outer frame. Adjust the tabs

according to the thickness of the cabinet side panel,

as shown below:

thickness of 20 mm: take off

the removable part of the tab

( )see diagram

thickness of 18 mm: use the

first groove, which has already

been set in the factory (see

diagram)

thickness of 16 mm: use the

second groove (see diagram)

Secure the appliance to the cabinet by opening the

oven door and putting 4 screws into the 4 holes of the

outer frame.

! All parts which ensure the safe operation of the

appliance must not be removable without the aid of a

tool.

Electrical Connection

Electrical connection

The electrical connection to the mains must be made

on the appliance. The power voltage and frequency

are as indicated on the rating plate.

! THIS APPLIANCE MUST BE EARTHED.

Connecting the po er supplw y ca leb

To open the terminal board:

 Using a screwdriver, press on the tabs situated on

each side of the terminal board cover.

 Pull open the terminal board cover.

To connect the power supply cable, proceed as

follows:

Unscrew the cable clamp screw and the contact

screws L-N-$.

 Fasten the wires beneath the screwheads using the

following colour scheme: Blue (N) Brow n(L)

Y wello -Green $

 Fasten the power supply cable in the

corresponding cable clamp and close the cover.

Electrical Connection:

Voltage Frequency: 230

V-1+N 50Hz

Fuse Section: 16A

Supply cable: 3x1.5mm2

You can connect your oven to the system means of a

terminal board. Refer to above information for the

minimal cable sections and the calibration of the

protective elements according to the connection.

If the appliance is installed w xith a j bunction o , an

omnipolar circuit reaker b - with a minimum contact

opening of 3mm - should be installed between the

appliance and the mains.

Po er ca le supplw b y connection to the electrical

mains:

We recommend you use a power supply cable which

is long enough to allow you to take the oven out of its

recess in the event of maintenance operations (only

use HAR - H 05 - RRF quality cables fitted with a plug

conforming to the regulations in force.

The plug must be accessible at all times.

U nplug the appliance before all operations, even

w hen replacing the oven lamp .

U sing the appliance without correct earthing is

highly dangerous.

! After connecting the appliance to the fle le x bi

cable, tighten all the scre on the terminal oardw s b .

4 2

N L

DATA PLATE

Dimensions

width cm 43.5

height cm 32

depth cm 40

Volume lt. 56

Electrical

connections

voltage: 230-240V ~ 50Hz

maximum power absorbed

2250W-2400W

Directive 2002/40/EC on the label

of electric ovens.

Standard EN 50304

ENERGY LABEL

Declared energy consumption for

Forced convection Class – heating

mode: Fan assisted

This appliance conforms to the

following European Economic

Community directives:

- 2006/95/EEC of 12/12/06 (Low

Voltage) and subsequent

amendments;

- 89/336/EEC of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments;

- 93/68/EEC of 22/07/93 and

subsequent amendments.

- 2002/96/EC

Product specificaties

Merk:	Hotpoint
Categorie:	Oven
Model:	BS43B
Soort bediening:	Draaiknop
Breedte:	600 mm
Hoogte:	600 mm
Verlichting binnenin:	Ja
Totale binnen capaciteit (ovens):	56 l
Aantal ovens:	1
Vermogen lamp:	40 W
Soort oven:	Elektrische oven
Type timer:	Digitaal
Instelbare thermostaat:	Ja