Hotpoint ARTXF 149 (EU) Handleiding

Hotpoint Wasmachine ARTXF 149 (EU)

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint ARTXF 149 (EU) (60 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/60

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washing machine

and starting a wash cycle, 4-5

Control panel

Indicator lights

How to open and shut the drum

Starting a wash cycle

Wash cycles, 6

Table of wash cycles

Personalisation, 7

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 8

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 9

General safety

Disposal

Saving energy and respecting the environment

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the washing machine

Caring for your appliance door and drum

Cleaning the pump

Checking the water inlet hose

How to clean the detergent dispenser

Troubleshooting, 11

Service, 12

ARTXF 149

Instructions for use

WASHING MACHINE

English,1

РУССКИЙ, 13

CIS

Polski,25

Italiano,37

Français,49

Installation

!Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to inform

the new owner as to its operation and features.

!Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the

washing machine.

2. Check whether the

washing machine has

been damaged during

transport. If this is the

case, do not install it

and contact your

retailer.

3. Remove the four

protective screws and

the rubber washer

with the respective

spacer, situated on

the rear of the

appliance (see figure).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if

the washing machine needs to be moved to

another location.

Warning: Warning: Warning: Warning: Warning: should the screws be re-used, make sure

you fasten the shorter ones at the top.

!Packaging materials are not children's toys.

Levelling

Your machine may make a considerable amount of

noise if the two front feet have not been adjusted

correctly.

1. Install the washing

machine on a flat

sturdy floor, without

resting it up against

walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, com-

pensate for any

unevenness by

tightening or loosening

the adjustable front feet (see figure); the angle of

inclination, measured according to the worktop,

must not exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Putting your appliance in place and moving it.

If your washing

machine is equipped

with a special set of

retractable wheels you

can easy move it. To

lower the wheels and

thus move the

appliance effortlessly,

just pull the lever,

situated on the left-

hand side beneath the

base. Once the

appliance is in the required position, put the lever

back in place. The washing machine is now firmly in

place (see figure).

Electric and water connections

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to a

cold water tab using a 3/

4 gas threaded

connection (see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the other

end of the water inlet

hose to the washing

machine, screwing it

onto the appliance's

cold water inlet, situated

on the top right-hand

side on the rear of the

appliance (see figure).

3. Make sure there are no kinks or bends in the hose.

!The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

!If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

Technical data

Model ARTXF 149

Dimensions

width 40 cm

height 85 cm

depth 60 cm

Capacity from 1 to 6 kg

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 42 litres

Spin speed up to 1400 rotations per minute

Energy rated

programmes

according to

regulation

EN 60456

programme 7; temperature 60°C;

using a load of 6 kg.

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

- 2006/95/EC (Low Voltage)

FP

Connecting the drain hose

Connect the drain hose,

without bending it, to a

drainage duct or a wall

drain located at a height

between 65 and 100 cm

from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

! We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

• the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

• the socket is compatible with the plug of the

washing machine. If this is not the case, replace

the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to rain,

storms and other weather conditions.

! When the washing machine has been installed, the

electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 2.

Product specificaties

Merk:	Hotpoint
Categorie:	Wasmachine
Model:	ARTXF 149 (EU)
Apparaatplaatsing:	Vrijstaand
Soort bediening:	Buttons,Rotary
Kleur van het product:	Wit
Ingebouwd display:	Ja
Breedte:	400 mm
Diepte:	600 mm
Hoogte:	850 mm
Type lader:	Bovenbelading
Deurkleur:	Wit
Uitgestelde start timer:	Ja
Energie-efficiëntieklasse (oud):	A
Energieverbruik wassen:	- kWu
Waterconsumptie per cyclus:	- l
Wasklasse:	A
Centrifuge-droger klasse:	B
Maximale centrifugesnelheid:	1400 RPM
Nominale capaciteit:	6 kg
Wasprogramma's:	Hygiene/anti-allergy,Black,Hand/wool,Intensive/outdoor