Hotpoint AQD1070D 69 Handleiding

Hotpoint Wasdroger AQD1070D 69

Lees hieronder de đź“– handleiding in het Nederlandse voor Hotpoint AQD1070D 69 (72 pagina's) in de categorie Wasdroger. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/72
EN
1
English,1
! This symbol reminds you to read this instruction manual.
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser drawer
Caring for your appliance drum
Cleaning the pump
Checking the water inlet hose
Precautions and advice, 5
General safety
Disposal
Opening the porthole door manually
Description of the machine, 6-7
Touch control panel
How to run a wash cycle or a drying
cycle, 8
Wash cycles and options, 9
Table of wash cycles
Wash options
Detergents and laundry, 10
Detergent
Preparing the laundry
Washing recommendations
Load balancing system
Trouble shooting, 11
Assistance, 12
EN
WASHER-DRYER
AQUALTIS
AQD1070D 69
Instructions for
installation and use
IT
Italiano,13
ES
Español,25
PT
PortuguĂŞs,37
NL
Nederlands,49
DE
Deutsch,61
EN
2
Installation
! This instruction manual should be kept in a
safe place for future reference. If the Washer-
dryer is sold, given away or moved, please
ensure the manual is kept with the machine,
so that the new owner may benefit from the
advice contained within it.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
! Inside the pack containing this manual, you
will also find the guarantee and all the details
necessary for installation.
Unpacking and levelling
Unpacking
1. Once you have removed all the packaging
from the Washer-dryer, make sure it has not
been damaged during transportation.
If it has been damaged, contact the retailer
and do not proceed any further with the
installation process.
2. Remove the 4
protective screws
(used during
transportation) and
the corresponding
spacer, located on
the rear part of the
appliance ( ). see figure
3. Close off the holes using the plastic plugs
supplied in the pack.
4. Keep all the parts in a safe place; they will
be needed again if the Washer-dryer is moved
to another location, to prevent the inside of the
appliance being damaged.
! Packaging materials should not be used as
toys for children.
Levelling
1. Place the Washer-
dryer on a flat sturdy
floor, without resting
it up against walls or
cabinets.
2. If the floor is
uneven, the front feet
of the machine may
be adjusted until it
reaches a horizontal
position (the angle of
inclination must not exceed 2 degrees).
! If the appliance is levelled correctly, it will
be more stable and much less likely to cause
vibrations and noise while it is operating,
particularly during the spin cycle.
! If it is placed on carpet or a rug, adjust the
feet in such a way as to allow a sufficient
ventilation space underneath the Washer-dryer.
Connecting the electricity and
water supplies
Connecting the water inlet hose
! Before connecting the inlet hose to the water
supply, run the water until it is perfectly clear.
1. Connect the inlet
hose to the machine
by screwing it onto
the cold water inlet of
the appliance, which
is situated on the top
right-hand side of
the rear part of the
appliance . (see figure)
2. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical data table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand or old inlet hoses;
use the products supplied with the machine.
EN
3
Connecting the drain hose
Connect the drain
hose to drain duct
piping or a wall drain
located between 65
and 100 cm above
the floor, making sure
it is not bent at all.
Alternatively, rest the
drain hose on the
side of a washbasin
or bathtub, fastening
the duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• the socket is earthed and complies with all
applicable laws;
• the socket is able to withstand the maximum
power load of the appliance as indicated in
the Technical data table (see opposite);
• the power supply voltage falls within the
values indicated in the Technical data table
(see opposite);
• the socket is compatible with the plug of the
appliance. If this is not the case, have the
socket or the plug replaced.
! The machine must not be installed outdoors,
even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! The mains socket must remain within easy
reach after the Washer-dryer has been installed.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable and plug must only
be replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these regulations
are not respected.
65 - 100 cm
Technical data
Model AQD1070D 69
Dimensions
width 59.5 cm
height 85 cm
depth 64.5 cm
Capacity
from 1 to 10 kg for the wash
programme
from 1 to 7 kg for the drying
programme
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 71 litres
Spin speed up to 1600 rotations per
minute
Energy ra-
ted
programmes
according to
regulation
EN 50229
Wash: programme ; tem-
perature 60°C; using a load
of 10 kg.
Drying: the smaller load
must be dried by selecting
the “EXTRA” dryness level.
The load must consist of 3
sheets, 2 pillowcases and
1 hand towel;
the remainder of the load
must be dried by selecting
the “EXTRA” dryness level.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU

Product specificaties

Merk: Hotpoint
Categorie: Wasdroger
Model: AQD1070D 69

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint AQD1070D 69 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wasdroger Hotpoint

Hotpoint

Hotpoint EU NTDG92 SK IT Handleiding

2 December 2024
Hotpoint

Hotpoint NT M11 92WK IT Handleiding

2 December 2024
Hotpoint

Hotpoint NT M11 8X3SKY IT Handleiding

2 December 2024
Hotpoint

Hotpoint NTS M11 9X3E IT Handleiding

2 December 2024
Hotpoint

Hotpoint NT M11 82K IT Handleiding

2 December 2024
Hotpoint

Hotpoint NT M11 9X3SKY IT Handleiding

2 December 2024
Hotpoint

Hotpoint NT M11 8X3K IT Handleiding

2 December 2024
Hotpoint

Hotpoint NT M11 82XB IT Handleiding

2 December 2024
Hotpoint

Hotpoint NT M11 9X3E IT Handleiding

16 November 2024
Hotpoint

Hotpoint HTX26EASWWW Handleiding

18 April 2024

Handleiding Wasdroger

Nieuwste handleidingen voor Wasdroger

Whirlpool

Whirlpool FFT M11 82WS FR Handleiding

3 December 2024
Whirlpool

Whirlpool FFT M11 72B EE Handleiding

3 December 2024
Whirlpool

Whirlpool W7D93WRFR Handleiding

3 December 2024
Whirlpool

Whirlpool FFT M11 9X3WSY Handleiding

3 December 2024
Whirlpool

Whirlpool FFT M22 8X2B Handleiding

3 December 2024
Whirlpool

Whirlpool W6 D84WB EE Handleiding

3 December 2024
Whirlpool

Whirlpool FFT D 9X3SBS PL Handleiding

3 December 2024
Whirlpool

Whirlpool MFTD9X3WC Handleiding

3 December 2024
Whirlpool

Whirlpool W7 D94WR PL Handleiding

3 December 2024
Whirlpool

Whirlpool FFT M22 9X2BS PL Handleiding

3 December 2024