Hoshizaki FS-1500MLH-C Handleiding

Hoshizaki Ijsmachine FS-1500MLH-C

Lees hieronder de 📖 handleiding in het Nederlandse voor Hoshizaki FS-1500MLH-C (41 pagina's) in de categorie Ijsmachine. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/41
Hoshizaki
“A Superior Degree
of Reliability”
www.hoshizaki.com
Models
FS-1001MLH-C with SRC-10H
FS-1022MLH-C with SRC-10H
FS-1500MLH-C with SRC-14H
INSTRUCTION MANUAL
Modular Cubelet
Serenity Series
Hoshizaki America, Inc.
Issued: 6-13-2014
2
WARNING
Only qualied service technicians should install and service the appliance. To
obtain the name and phone number of your local Hoshizaki Certied Service
Representative, visit www.hoshizaki.com. No installation or service should be
undertaken until the technician has thoroughly read this Instruction Manual.
Likewise, the owner/manager should not proceed to operate the appliance until the
installer has instructed them on its proper operation. Failure to install, operate, and
maintain the appliance in accordance with this manual will adversely affect safety,
performance, component life, and warranty coverage and may result in costly water
damage. Proper installation is the responsibility of the installer. Product failure or
property damage due to improper installation is not covered under warranty.
Hoshizaki provides this manual primarily to assist qualied service technicians in the
installation, maintenance, and service of the appliance.
Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, send an e-mail message, or write to the Hoshizaki Technical
Support Department for assistance.
Phone: 1-800-233-1940; (770) 487-2331
Fax: 1-800-843-1056; (770) 487-3360
E-mail: techsupport@hoshizaki.com
HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City, GA 30269
Attn: Hoshizaki Technical Support Department
NOTE: To expedite assistance, all correspondence/communication MUST include the
following information:
• Model Number
• Serial Number
• Complete and detailed explanation of the problem.
3
CONTENTS
Important Safety Information 5 .................................................................................................
I. Specications 7 ......................................................................................................................
A. Electrical and Refrigerant Data 7 .....................................................................................
1. FS ............................................................................................................................ 7
2. SRC 7 .........................................................................................................................
B. Dimensions/Connections 8 ..............................................................................................
1. FS-1001MLH-C 8 ........................................................................................................
2. FS-1022MLH-C 9 ........................................................................................................
3. FS-1500MLH-C...................................................................................................... 10
4. SRC-10H ................................................................................................................11
5. SRC-14H ............................................................................................................... 12
II. Installation and Operating Instructions ............................................................................ 13
A. Location ...................................................................................................................... 13
1. Icemaker ................................................................................................................ 13
2. Remote Condensing Unit ....................................................................................... 14
B. Checks Before Installation ........................................................................................... 15
1. Icemaker ................................................................................................................ 15
2. Remote Condensing Unit ....................................................................................... 15
C. How to Remove Panels ............................................................................................... 16
1. Icemaker ................................................................................................................ 16
2. Remote Condensing Unit ....................................................................................... 16
D. Installation of the Icemaker ......................................................................................... 17
1. Dispenser Unit/Ice Storage Bin and Icemaker Setup ............................................. 17
2. Icemaker Electrical Connection ............................................................................. 18
3. Water Supply and Drain Connections .................................................................... 19
E. Installation of the Remote Condensing Unit 21 ................................................................
1. Remote Condensing Unit Setup 21 .............................................................................
2. Line Set Size and Refrigerant Charge 21 ...................................................................
3. Line Set Installation 23 ...............................................................................................
a) Factory Line Set Installation 23 ...............................................................................
b) Field Fabricated Line Set Installation.................................................................. 24
4. Remote Condensing Unit Electrical Connection 26 ....................................................
F. Final Checklist 27 ..............................................................................................................
G. Startup 28 ........................................................................................................................
H. Bin Control Check 29 .......................................................................................................
1. Infrared Sensor Check 29 ...........................................................................................
2. Mechanical Backup Bin Control Check 31 ..................................................................
3. Infrared Sensor Shutdown Delay 32 ...........................................................................
a) Standard Ice Storage Bin 32 ...................................................................................
b) Dispenser Unit 32 ....................................................................................................
I. Operation Notes 32 ...........................................................................................................
IMPORTANT
This manual should be read carefully before the appliance is installed and operated.
Read the warnings and guidelines contained in this manual carefully as they
provide essential information for the continued safe use and maintenance of the
appliance. Retain this manual for any further reference that may be necessary.
4
III. Maintenance 33 ...................................................................................................................
A. Maintenance Schedule 34 ................................................................................................
B. Cleaning and Sanitizing Instructions 35 ...........................................................................
1. Cleaning Solution 35 ...................................................................................................
2. Cleaning Procedure 35 ...............................................................................................
3. Sanitizing Solution 36 .................................................................................................
4. Sanitizing Procedure - Initial 36 ..................................................................................
5. Sanitizing Procedure - Final 37 ...................................................................................
IV. Preparing the Appliance for Periods of Non-Use 39 ............................................................
V. Disposal 40 ...........................................................................................................................
5
Important Safety Information
Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, damage to the appliance, or damage to property.
WARNING Indicates a hazardous situation which could result in death or
serious injury.
NOTICE Indicates a situation which could result in damage to the
appliance or property.
IMPORTANT Indicates important information about the use, installation, and
care of the appliance.
WARNING
The appliance should be destined only to the use for which it has been expressly
conceived. Any other use should be considered improper and therefore dangerous.
The manufacturer cannot be held responsible for injury or damage resulting from
improper, incorrect, and unreasonable use. Failure to install, operate, and maintain the
appliance in accordance with this manual will adversely affect safety, performance,
component life, and warranty coverage and may result in costly water damage.
To reduce the risk of death, electric shock, serious injury, or re, follow basic
precautions including the following:
• Only qualied service technicians should install and service the appliance.
The appliance must be installed in accordance with applicable national, state, and
local codes and regulations.
To reduce the risk of electric shock, do not touch the icemaker power switch or plug
with damp hands. Make sure the icemaker power switch is in the "OFF" position
before plugging in or unplugging the icemaker.
Before Servicing: FS: Move the icemaker's power switch to the "OFF" position.
Unplug the icemaker from the electrical outlet. SRC: Turn off the power supply to
the remote condensing unit. Place the disconnect (if applicable) in the off position.
Lockout/Tagout to prevent the power supply from being turned back on inadvertently.
• Do not make any alterations to the icemaker or condensing unit. Alterations could
result in electric shock, injury, re, or damage to the appliance.
FS
The icemaker requires an independent power supply of proper capacity. See the
nameplate for electrical specications. Failure to use an independent power supply of
proper capacity can result in a tripped breaker, blown fuse, damage to existing wiring,
or component failure. This could lead to heat generation or re.
THE ICEMAKER MUST BE GROUNDED. The icemaker is equipped with a
NEMA5-15 three-prong grounding plug to reduce the risk of potential shock
hazards. It must be plugged into a properly grounded, independent 3-prong wall outlet.
If the outlet is a 2-prong outlet, it is your personal responsibility to have a qualied
electrician replace it with a properly grounded, independent 3-prong wall outlet. Do not
remove the ground prong from the power cord and do not use an adapter plug. Failure
to properly ground the icemaker could result in death or serious injury.
6
WARNING, continued
FS continued
• Do not use an extension cord.
• Do not use an icemaker with a damaged power cord. The power cord should not be
altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could result
in electric shock or re. To unplug the icemaker, be sure to pull the plug, not the cord,
and do not jerk the cord.
• Do not place ngers or any other objects into the ice discharge opening.
SRC
• Electrical connection must be hard-wired to the remote condensing unit and must
meet national, state, and local electrical code requirements. Failure to meet these
code requirements could result in death, electric shock, serious injury, re, or damage.
The remote condensing unit requires an independent power supply of proper capacity.
See the nameplate for electrical specications. Failure to use an independent power
supply of proper capacity can result in a tripped breaker, blown fuse, damage to
existing wiring, or component failure. This could lead to heat generation or re.
THE REMOTE CONDENSING UNIT MUST BE GROUNDED. Failure to properly
ground the remote condensing unit could result in death or serious injury.
NOTICE
• Follow the instructions in this manual carefully to reduce the risk of costly water
damage.
• In areas where water damage is a concern, install in a contained area with a oor
drain.
• Install the icemaker in a location that stays above freezing. Normal operating ambient
temperature must be within 45°F to 100°F (7°C to 38°C).
• Do not leave the icemaker on during extended periods of non-use, extended
absences, or in sub-freezing temperatures. To properly prepare the icemaker for
these occasions, follow the instructions in "IV. Preparing the Appliance for Periods of
Non-Use."
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear
of obstruction.
• Do not place objects on top of the appliance.
The dispenser unit/ice storage bin is for ice use only. Do not store anything else in the
dispenser unit/ice storage bin.
8
B. Dimensions/Connections
1. FS-1001MLH-C Units: mm [in.]
Rear
Side
Bottom
Model Shown: FS-1001MLH-C
NOTICE
Allow 6" (15 cm) clearance at rear and sides for proper air circulation and ease of
maintenance and/or service should they be required. Allow 24" (61 cm) clearance at
top to allow for removal of the auger.
The storage bin opening must match the bottom opening as in the illustration.
10
3. FS-1500MLH-C
Units: mm [in.]
Rear
Side
Bottom
Model Shown: FS-1500MLH-C
NOTICE
Allow 6" (15 cm) clearance at rear and sides for proper air circulation and ease of
maintenance and/or service should they be required. Allow 24" (61 cm) clearance at
top to allow for removal of the auger.
The storage bin opening must match the bottom opening as in the illustration.
11
4. SRC-10H
Unit: mm [in.]
Note: Legs are included with condensing unit.
Leg height is 380 mm (14-15/16 in.).
Rear
Top
SRC-10H Heat of Rejection
AT 90°F (32°C)
WT 70°F (21°C)
10,500 BTU/hr
NOTICE
Allow 24" (61cm) clearance at front
and rear for proper air circulation and
ease of maintenance and/or service
should they be required.
12
5. SRC-14H
Unit: mm [in.]
Note: Legs are included with condensing unit.
Leg height is 380 mm (14-15/16 in.).
Rear
Top
SRC-14H Heat of Rejection
AT 90°F (32°C)
WT 70°F (21°C)
17,700 BTU/hr
NOTICE
Allow 24" (61cm) clearance at front
and rear for proper air circulation and
ease of maintenance and/or service
should they be required.
13
II. Installation and Operating Instructions
WARNING
The icemaker and remote condensing unit must be installed in accordance with
applicable national, state, and local codes and regulations.
• Failure to install, operate, and maintain the icemaker and remote condensing
unit in accordance with this manual will adversely affect safety, performance,
component life, and warranty coverage and may result in costly water damage.
Ensure all components, fasteners, and thumbscrews CHOKING HAZARD:
are securely in place after installation. Make sure that none have fallen into the
dispenser unit/ice storage bin.
A. Location
1. Icemaker
NOTICE
The icemaker is not intended for outdoor use. Normal operating ambient
temperature must be within 45°F to 100°F (7°C to 38°C); Normal operating
water temperature must be within 45°F to 90°F (7°C to 32°C). Operation of the
icemaker, for extended periods, outside of these normal temperature ranges may
affect icemaker performance.
The icemaker will not work at sub-freezing temperatures. To prevent damage
to the water supply line, drain the icemaker if the air temperature is going to go
below 32°F (0°C). See "IV. Preparing the Appliance for Periods of Non-Use."
The icemaker should not be located next to ovens, grills, or other high heat producing
equipment.
Allow 6" (15 cm) clearance at rear and sides for proper air circulation and ease of
maintenance and/or service should they be required. Allow 24" (61 cm) clearance at top to
allow for removal of the auger.
The location must provide a rm and level foundation for the appliance.
16
C. How to Remove Panels
1. Icemaker
• Front Panel: Remove the screw. Lift up and towards you.
Top Panel: Lift up at front slightly, push rearward and lift off.
• Left Side Panel and Right Side Panel: Remove the thumbscrew (FS-1001MLH-C) or
screw (FS-1022MLH-C and FS-1500MLH-C). Slide forward slightly and lift off.
2. Remote Condensing Unit
Top Panel: Remove the screws and lift off.
• Louver Panel: Remove the screws and lift off.
• Left Side Panel and Right Side Panel: Remove the screws and lift off.
• Control Box Cover: Remove the screws and lift off.
Left Side Panel
Fig. 4
Top Panel
Right Side Panel
Louver Panel
Left Side Panel
Remote Condensing Unit
Right Side Panel
Fig. 3
Top Panel
Front Panel
FS-1022MLH-C or FS-1500MLH-C Icemaker
Control Box Cover
Model Shown: FS-1022MLH-C
Model Shown: SRC-10H
FS-1001MLH-C Icemaker
Top Panel
Front Panel
Left Side Panel
Right Side Panel
17
D. Installation of the Icemaker
1. Dispenser Unit/Ice Storage Bin and Icemaker Setup
WARNING
The installer must ensure the dispenser unit/ice storage bin is compatible with
the icemaker, and the dispenser unit/ice storage bin and icemaker are properly
attached and secured.
1) If mounting the icemaker on top of a dispenser unit, follow the dispenser unit's setup
procedure. If mounting the icemaker on top of an ice storage bin, unpack the ice storage
bin, and attach the 4 adjustable legs provided (bin accessory) to the bottom of the ice
storage bin.
2) Position the dispenser unit/ice storage bin in its permanent location.
3) If required, install an adapter kit or top kit. Contact your local Hoshizaki distributor for
recommendations.
4) Level the dispenser unit/ice storage bin in both the left-to-right and front-to-rear
directions. Ifusing an ice storage bin, adjust the ice storage bin legs to level.
5) Place the icemaker on top of the dispenser unit/ice storage bin.
6) Follow the dispenser unit/ice storage bin, adapter kit, or top kit instructions for securing
the icemaker. If no instructions are available, secure the icemaker using the mounting
brackets provided. Secure the mounting brackets to the icemaker with the 5×12
machine bolts provided. See Fig. 5. Secure the mounting brackets to the dispenser unit
with the self-tapping bolts provided. NOTICE! Use care to avoid damage to dispenser
unit/ice storage bin components when attaching the mounting brackets.
Icemaker
Fig. 5
Self-Tapping Bolts
Mounting
Brackets
5×12 Machine Bolts
Model Shown: FS-1500MLH-C
Dispenser
Unit
Ice
Storage
Bin
Model Shown: FS-1500MLH-C
Mounting
Brackets
Icemaker
18
2. Icemaker Electrical Connection
IMPORTANT
Icemaker and remote condensing unit power supplies are separate.
WARNING
• Electrical connection must meet national, state, and local electrical code
requirements. Failure to meet these code requirements could result in death,
electric shock, serious injury, re, or damage.
The icemaker requires an independent power supply of proper capacity. See the
nameplate for electrical specications. Failure to use an independent power supply
of proper capacity can result in a tripped breaker, blown fuse, damage to existing
wiring, or component failure. This could lead to heat generation or re.
THE ICEMAKER MUST BE GROUNDED. The icemaker is equipped with a
NEMA5-15 three-prong grounding plug to reduce the risk of potential shock
hazards. It must be plugged into a properly grounded, independent 3-prong wall
outlet. If the outlet is a 2-prong outlet, it is your personal responsibility to have
a qualied electrician replace it with a properly grounded, independent 3-prong
wall outlet. Do not remove the ground prong from the power cord and do not use
an adapter plug. Failure to properly ground the icemaker could result in death or
serious injury.
• Do not use an extension cord.
To reduce the risk of electric shock, do not touch the icemaker power switch or plug
with damp hands. Make sure the icemaker power switch is in the "OFF" position
before plugging in or unplugging the icemaker.
• Do not use an icemaker with a damaged power cord. The power cord should not be
altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could
result in electric shock or re. To unplug the icemaker, be sure to pull the plug, not
the cord, and do not jerk the cord.
The GREEN ground wire in the factory-installed power cord is connected to the
icemaker. If it becomes necessary to remove or replace the power cord, be sure
to connect the power cord's ground wire.
• Usually an electrical permit and services of a licensed electrician are required.
The maximum allowable voltage variation is ±10 percent of the nameplate rating.
19
3. Water Supply and Drain Connections
See Fig. 6
WARNING
Water supply and drain connections must be installed in accordance with applicable
national, state, and local regulations.
NOTICE
• Normal operating water temperature should be within 45°F to 90°F (7°C to
32°C). Operation of the appliance, for extended periods, outside of this normal
temperature range may affect performance.
To prevent damage to the appliance, do not operate the appliance when the water
supply is off, or if the pressure is below 10 PSIG. Do not run the appliance until
the proper water pressure is reached.
A plumbing permit and services of a licensed plumber may be required in some areas.
• External lters, strainers, or softeners may be required depending on water quality. Contact
your local Hoshizaki Certied Service Representative or local Hoshizaki distributor for
recommendations.
Water supply pressure must be a minimum of 10 PSIG and a maximum of 113 PSIG. If the
pressure exceeds 113 PSIG, the use of a pressure reducing valve is required.
The icemaker drain line and dispenser unit/ice storage bin drain line must be run
separately.
• Drain lines must have 1/4" fall per foot (2 cm per 1 m) on horizontal runs to get a good
ow. A vented tee connection is also required for proper ow.
• Drain lines should not be piped directly to the sewer system. An air gap of a minimum of
2 vertical inches (5 cm) should be between the end of the drain pipe from the icemaker
and dispenser unit/ice storage bin and the oor drain.
22
Max.
16.5'
(10 m)
Max.
16.5'
(10 m)
Line Set Connections
Fig. 8
Remote
Condensing Unit
(with compressor)
Icemaker
Service Loop
Icemaker
Suction Line
"S" Oil-Trap
Service Loop
Remote
Condensing Unit
(with compressor)
5/8" OD Suction Line
(insulated)
Model Shown: FS-1022MLH-C with SRC-10H
Hoshizaki
Icemaker
Liquid
Line
FS-1001MLH-C
FS-1022MLH-C 1/4" OD
FS-1500MLH-C 3/8" OD
Ice
Storage
Bin
Ice
Storage
Bin
Max. 33' (10 m)
Max. 10' (3 m)
5/8" OD Suction Line
(insulated)


Product specificaties

Merk: Hoshizaki
Categorie: Ijsmachine
Model: FS-1500MLH-C

Heb je hulp nodig?

Als je hulp nodig hebt met Hoshizaki FS-1500MLH-C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Ijsmachine Hoshizaki

Handleiding Ijsmachine

Nieuwste handleidingen voor Ijsmachine