Honeywell Performance H4W2PER2 Handleiding

Honeywell Bewakingscamera Performance H4W2PER2

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell Performance H4W2PER2 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
H4W2PER2 WDR 1080P IR Dome Camera
Quick Installation Guide
Thank you for purchasing a Honeywell Performance Series
IP camera. Follow the instructions in this guide to install
and log in to your camera. For instructions on configuring
the camera, refer to the user guide on the CD that came
with your camera. If you require additional assistance, call
the number listed for your region on the back cover.
Warnings and Cautions
WARNING
To ensure compliance with electrical safety standards, this product is
intended for use with a Listed Power Adapter marked “Limited Power
Source” or “LPS” on the unit, output rated to 12 VDC, minimum 0.33 A,
TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed
Information Technology Equipment meeting IEEE 802.3af PoE standard.
CAUTION
The Ethernet connection is not intended to be connected to exposed
(outside plant) networks. Do not connect two power sources to the camera at
the same time.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to beam.
Important Safeguards
•
Read and keep these instructions
•
Confirm the installation surface can support at least three times the weight of the camera.
•
Do not apply power to the camera before completing installation.
•
Do not aim the camera toward a bright light source for extended periods to prevent damage to
the imager.
•
Avoid operating the unit under or close to unstable light sources (may cause flickering), or close
to fluorescent lamps or objects reflecting light.
•
Do not touch the camera lens.
•
Do not drop the camera or subject it to physical shock.
•
Do not use a strong or abrasive detergent when cleaning the camera.
•
Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where
the operating temperature is outside the recommended range of - (-22°F to 140°F 30°C to
60°C).
Before You Begin
Before you begin, check that you have received all the parts listed below. If any parts are
missing or damaged, contact your dealer immediately.
•
Camera
•
Installation CD
•
Quick installation guide
•
Allen key - (L wrench)
•
Self-tapping screws (×4)
•
Plastic anchors (×4)
•
Mounting template
CAUTION Installation and servicing should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain your
warranty.
Mounting surface
Mounting template
Anchors
Camera assembly
Self-tapping screws
Dome cover
Locking screw
Allen key
Preparing the Mounting Surface
1.
Apply the mounting template to the mounting surface.
2.
Using the mounting template as a guide, drill three pilot holes in the mounting surface,
then hammer the supplied anchors into the holes.
3.
Drill a cable entry hole in the mounting surface, then pull the required cables through the hole.
CAUTION
THIS SYMBOL INDICATES THAT
DANGE OUSR VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CA : TUTION O REDUCE THE RISK OF ELECTRIC
SHOCK, DO N T REM THE CO OVE OVER.
NO USER-SERVICEABLE PAR .TS INSIDE
REFER SER TO QUVICING ALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
RISK OF ELECTRIC
SHOCK
DO N T OPENO
© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such ch anges.
Mounting and Aiming the Camera
1.
Remove the dome cover from the camera assembly using the supplied Allen key.
2.
If you using microSD with are a card the install it before continuing. See below for camera,
details.
slide metal
shell to
unlock
2. Open
metal
shell.
3. Insert microSD
card.
4. Close metal
shell and
slide to lock
position.
3.
Connect the cable to the RJ 45 port on theEthernet - camera.
4.
If the other end of Ethernet cable is connected to a PoE (Powerthe not -over Ethernet) -
switch or NVR, connect the power connector of the camera to a 12 VDC power source.
5.
Fix the camera assembly to the mounting surface using the supplied screws.
6.
Aim screw the camera lens in the desired direction, then tighten the s on the camera
assembly.
7.
Reattach the dome cover.
Logging On to the Camera
If the camera is connected to the PoE port of a Honeywell Embedded NVR, it can be configured
using the NVR.
To log on remotely from a PC, install the Honeywell Config Tool from the software and
documentation CD, find the camera on the network, and then open the web browser with the
Honeywell Config Tool. The default user name is admin (case sensitive) the- and default password
is . 1234
Note
• Only Internet Explorer 11 (or later) is supported.
• IP address of the device is assigned automatically by server. If the DHCP server DHCP
is not available, the device will acquire as the default IP 192.168.1.108 address.
Adjusting the Zoom and Focus Settings
After you have logged on to the camera, go to Setup > Camera > Conditions > Zoom and
Focus to fine tune the camera’s zoom and focus settings.-
Recommended Recorders
HEN*4 - 8/16/32/64 channel Focus 4K NVRs (H.264 and H.265)
HEN*3 4/8/16/32- )channel Performance Series NVRs (H.264 and H.265
HEN*2 4/8/16-channel Performance Series NVRs (H.264)
HRHT4* 4/8/16- channel 4 MP HQA/IP/CVBS Hybrid DVRs (H.264)
Regulatory Statements
FCC Compliance
This equipment has been tested and found to comply with the for a limits Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user isencouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
North America The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.
Europe The manufacturer declares that the equipment supplied is compliant with the European Parliament
and Council Directive on the of restriction the use of certain hazardous substances in electrical and electronic
equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and the essential of requirements
the EMC directive (2014/30/EU), conforming to the requirements of standards EN 55032 for emissions, EN
50130-4 for immunity, and EN -1 for 62368 electrical equipment safety.
WEEE (Waste and Electronic Equipment)Electrical
Correct disposal of this product (applicable in the European Union and other European countries with
separate collection systems).This product should be disposed of, at the end of its useful life, as per
applicable local laws, regulations, and procedures.
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY, 40299, USA
www.honeywell.com/security
+1 800 323 4576
(North America only)
Aston Fields Road, Whitehouse Industrial
Estate Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
+1 44 (0) 1928 754 028
(Europe only)
Building #1, 555 Huanke Road, Zhang
Jiang Hi- Tech Park
Pudong New Area, Shanghai, 201203,
China www.asia.security.honeywell.com
+400 840 2233
(Asia Pacific only)
Document 800-2459 094 – – Rev A /2018

Product specificaties

Merk: Honeywell
Categorie: Bewakingscamera
Model: Performance H4W2PER2

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell Performance H4W2PER2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Bewakingscamera Honeywell

Honeywell

Honeywell HC35WE5R3 Handleiding

20 December 2024
Honeywell

Honeywell Performance H4W8PER2V Handleiding

20 December 2024
Honeywell

Honeywell HDZ30A Handleiding

11 Juni 2023
Honeywell

Honeywell Performance HD31H Handleiding

7 Juni 2023
Honeywell

Honeywell HD50 Handleiding

2 Juni 2023
Honeywell

Honeywell Equip HDZ30 Handleiding

28 Mei 2023
Honeywell

Honeywell Performance HBW8PR2 Handleiding

28 Mei 2023
Honeywell

Honeywell HDZ36AEX Handleiding

28 Mei 2023
Honeywell

Honeywell Acuix HDV1NDFSW Handleiding

25 Mei 2023
Honeywell

Honeywell Enterprise HERC96T24S Handleiding

25 Mei 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Hikvision

Hikvision DS-2CE12KF3T-LS Handleiding

18 December 2024
Hikvision

Hikvision DS-2CE78D0T-LXTS/A Handleiding

18 December 2024
TP Link

TP Link VIGI C450 Handleiding

18 December 2024
Hikvision

Hikvision DS-2CE76U0T-LPF Handleiding

18 December 2024
Hikvision

Hikvision DS-2CE78U0T-LF Handleiding

18 December 2024
Hikvision

Hikvision DS-2CE16U0T-LPF Handleiding

18 December 2024
Hikvision

Hikvision DS-2CE72KF3T-LSYE Handleiding

18 December 2024
Hikvision

Hikvision DS-2CE17U0T-LF Handleiding

18 December 2024
Hikvision

Hikvision DS-2CE72KF3T-LS Handleiding

18 December 2024
Hikvision

Hikvision DS-2CE12KF3T-LSYE Handleiding

18 December 2024