Honeywell HZ-826FTE Handleiding

Honeywell Kachel HZ-826FTE

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell HZ-826FTE (50 pagina's) in de categorie Kachel. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/50
GB
D
F
NL
E
P
I
SVE
FIN
GR
T
RS
PL
CZ
HU
AR
NOR
DNK
HZ-823FE
HZ-824FE
HZ-820E
HZ-821E
HZ-822E
HZ-825TE
HZ-826FTE
CONVECTOR
U S E R I N S T R U C T I O N S
KONVEKTOR
G E B R A U C H S A N W E I S U N G
CONVECTEUR
M A N U E L D U T I L I S AT I O N
CONVECTOR
B E D I E N I N G S H A N D L E I D I N G
CONVECTOR
M A N U A L D E L P R O P I E TA R I O
CONVECTOR
M A N U E L D O U T I L I Z A D O R
CONVETTORE
M A N U A L E D ' U S O
CONVECTOR
B R U K S A N V I S N I N G
KONVEKTOR
B R U K S A N V I S N I N G
KONVEKTOR
B R U G G E R H Å N D B O G
CONVECTOR
K Ä Y T T Ö O H J E E T
θερμαντικ σωμα (καλοριφερ)
√¢∏°π∂™ Ã∏™∏™
KONVEKTÖR
KULLANIC I TA L M AT LARI
KОНВЕКТОР
àçëíêìäñàà èé ùäëèãìÄíÄñàà
OGRZEWACZ
INSTRUKCJA OBS¸UGI
KONVEKTOR
NÁVOD K POUÎITÍ
KONVEKTOR
HASZNÁLATI UTASÍTÁS
ΩGóîà°S’G äɪ«∏©J
FIG. 2FIG. 1
FIG. 4FIG. 3
FIG. 6FIG. 5
FIG. 8FIG. 7
ENGLISH
IMPORTANT SAFETY
INSTRUCTIONS
Read all instructions before using heater.
1. Connect the appliance only to single
phase AC of the voltage specified on the
rating plate.
2. This appliance complies with EMC direc-
tive 89/336/EEC regarding radio and
television interference.
3. Keep combustible materials such as furni-
ture, pillows, bedding, papers, clothes
and curtains at least 90 cm from the
heater.
4. Extreme caution is necessary when any
heater is used by or near children.
5. Always unplug the heater when not in
use. Do not pull on the cord when discon-
necting it.
6. Do not cover. If covered, there is a fire risk.
7. DO NOT use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
8. This heater must not be located immedi-
ately below an electrical socket-outlet.
9. If the supply cord of this appliance is
damaged it must be replaced by a repair
shop appointed by the manufacturer, be-
cause special purpose tools are required.
10. Keep this heater clean. DO NOT allow
objects to enter any ventilation or exhaust
opening as this may cause electric shock,
or fire, or damage the heater.
11. Do not operate the unit before it is com-
pletely assembled according to the assem-
bly instructions.
ASSEMBLY INSTRUCTIONS
This heater may be used with feet on the
floor or attached directly to the wall.
For floor use, attach the feet to the lower
part of the heater by snapping each foot in-
to the matching holes (fig. 1).
Firmly press each foot until a “click” is
heard. Place the heater on a firm, level,
open surface at least 90 cm away from any
other object. DO NOT use on an unstable
surface such as bedding or deep carpeting.
For wall mounting, secure the wall attach-
ment clips into the wall with the screws pro-
vided. DO NOT install this heater in the im-
mediate surroundings of a bath, a shower
or swimming pool.
Attach the wall spacers on the back of the
heater to keep the minimum distance to the
wall. Attach the heater to the mounting
clips, using the mounting holes on the back
of the heater (fig.2).
OPERATION INSTRUCTIONS
A) MODEL HZ-820E
Turn the thermostat anticlockwise to its low-
est setting (d).
Plug in the heater.
Turn the thermostat clockwise to the highest
temperature setting, for a rapid warming
(fig.3).
When the room reaches a comfortable tem-
perature, turn the thermostat anti clockwise
until the heater switches off. At this setting,
the thermostat will automatically turn the
heater on (the pilot light illuminates) and off
(the pilot light goes out) to maintain the se-
lected temperature.
To turn the heater off, turn the thermostat an-
ti clockwise to the lowest setting (d) and un-
plug the heater.
B) MODELS HZ-821E, HZ-822E,
HZ-825TE
Turn the switch to (0).
Plug the heater into an outlet.
Turn the switch to the desired power, (I-Low,
II-Medium, III-High) (fig. 4).
Turn the thermostat clockwise to its highest
setting for a rapid warming.
When the room reaches a comfortable tem-
perature, turn the thermostat anticlockwise
until the heater switches off. At this setting,
the thermostat will automatically turn the
heater on (the pilot light illuminates) and off
(the pilot light goes out) to maintain the se-
lected temperature.
To turn the heater off, turn the switch to the
(0) position and unplug it.
C) TURBO
MODELS HZ-823FE, HZ-824FE
AND HZ-826FTE ONLY.
Turn the switch to (0).
Plug the heater into an outlet.


Product specificaties

Merk: Honeywell
Categorie: Kachel
Model: HZ-826FTE

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell HZ-826FTE stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Kachel Honeywell

Handleiding Kachel

Nieuwste handleidingen voor Kachel