Honeywell HDZ22HD Handleiding

Honeywell Bewakingscamera HDZ22HD

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell HDZ22HD (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 79 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Document 800-11874V5 – Rev A – 01/2015

HDZ Series IP PTZ Dome Quick Installation Guide

800-11874V5 - Rev A - 01/2015

Cautions and Warnings

WARNING Installation and servicing should be performed only by qualified

and experienced technicians to conform to all local codes and to maintain your

warranty.

WARNING To ensure compliance with electrical safety standards, CSA

Certified/UL Listed Class 2 power adapters are required. Power over Ethernet

(PoE+) shall be supplied by listed Information Technology Equipment meeting

the IEEE 802.3at-2009 PoE+ standard. The PoE is not intended to be connected

to exposed (outside plant) networks.

IMPORTANT NOTE

Regarding PoE operation of models HDZ22HDE(X), HDZ36E(X) and

HDZ30HDE

A high power PoE injector capable of supplying at least 60 W is required for proper

operation of outdoor camera models HDZ22HDE(X), HDZ36E(X) and HDZ30HDE, as PoE

to IEEE802.3af or IEEE802.3at will not support this model.

FCC Statement of Compliance

Information to the User:

This equipment has been tested and fo

und to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Note Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

Manufacturer’s Declaration of Conformance

The manufacturer declares that the equipment supplied with this guide is compliant with the

European Parliament and Council Directive on the Restrictions of the use of certain Hazardous

Substances in electrical and electronic equipment (2011/65/EU), General Product Safety Directive

(2001/95/EC) and the essential requirements of the EMC Directive (2004/108/EC), conforming to the

requirements of standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950-1 for

electrical equipment safety.

CAUTION This is a Class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take adequate

measures.

WARNING To comply with EN50130-4 requirements, a UPS should be

employed when powering the camera from 24 V AC.

Waste Electrical and Electronic Equipment (WEEE)

Safety Instructions

Before installing or operating the unit, read and follow all instructions. After

installation, retain the safety and operating instructions for future reference.

1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.

2. INSTALLATION

• Install in accordance with the manufacturer’s instructions.

• Installation and servicing should be performed only by qualified and experienced

technicians to conform to all local codes and to maintain your warranty.

• Do not install indoor rated models in outdoor locations.

• Any wall or ceiling mounting of the product should follow the manufacturer’s instructions

and use a mounting kit approved or recommended by the manufacturer.

3. POWER SOURCES - This product should be operated only from the type of power source

indicated on the marking label.

4. HEAT - Situate away from items that produce heat or are heat sources such as radiators, heat

registers, stoves, or other products (including amplifiers).

5. MOUNTING SYSTEM - Use only with a mounting system recommended by the manufacturer,

or sold with the product.

6. ATTACHMENTS

- Do not use attachments not recommen

ded by the product manufacturer as

they may result in the risk of fire, electric shock, or injury to persons.

7. ACCESSORIES - Only use accessories specified by the manufacturer.

8. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

9. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service

personnel.

10. REPLACEMENT PARTS - When replacement parts are required, be sure the service

technician has used replacement parts specified by the manufacturer or have the same

characteristics as the original part. Unauthorized substitutions may result in fire, electric shock

or other hazards. Using replacement parts or accessories other than the original

manufacturers may invalidate the warranty

CAUTION Risk of explosion if Battery is replaced by an incorrect type. Dispose of

used batteries in accordance with local laws.

Before You Begin

The Honeywell HDZ Series True Day/Night IP PTZ dome camera is a high resolution

network camera PTZ series designed for use in a wide range of applications. The camera

supports H.264 compression and quad video streaming. Streaming options include:

• HDZ30HD, HDZ22HD(X), HDZ30HDE and HDZ22HDE(X): Up to 30 frames per

second (NTSC) or 25 fps (PAL) in 1080p resolution (1920 x 1080). Up to 60 fps

(NTSC) or 50 fps (PAL) in 720p resolution (1280 x 720).

• HDZ30(X), and HDZ36E(X): Up to 60 frames per second (NTSC) or 50 fps (PAL) at

D1 resolution (720 x 486 NTSC; 720 x 576 PAL).

Before you begin, check that you have received all of the parts listed below. If any parts

are missing or damaged, contact your dealer immediately.

Assembling the Camera

Camera assembly is quick and easy. To assemble the camera:

1. Take the camera and all other components out of the packaging.

2. Rotate and remove the protective cover bag from the camera body.

3. Use the torx driver to remove the dome cover.

4. Remove the foam and tape from inside the dome.

5. Remove the lens cap from the camera lens.

6. Use the torx driver to fasten the dome cover to the camera body.

Note Optional: Use the lubricant on the dome cover’s rubber ring to make it easier to

re-attach to the housing and seal the PTZ dome cover and housing without water

coming in. Be careful to not get any lubricant on the dome as it may interfere with

viewing PTZ images.

7. Leave the protective film on the dome cover until installation is complete.

Mounting the Camera

You can install the camera to a ceiling, wall, pole, parapet, or roof using the following

Honeywell products:

Correct Disposal of this Product (applicable in the European Union and other

European countries with separate collection systems).

This product should be disposed of, at the end of its useful life, as per applicable local

laws, regulations, and procedures.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

DO NOT OPEN

RISK OF ELECTRIC SHOCK

Indoor models:

HDZ30HD

HDZ22HD(X)

HDZ30(X)

• PTZ dome camera

• Indoor mount kit

• Honeywell logo label

• Lubricant

• Installation CD

• Quick Installation Guide

• Torx driver

Outdoor models:

HDZ30HDE

HDZ22HDE(X)

HDZ36E(X)

• PTZ dome camera

• Outdoor mount kit

• Honeywell logo label

• Lubricant

• Installation CD

• M5 security and standard

screws (1 each)

• Quick Installation Guide

• Torx driver

Model No. Description Indoor Outdoor

HDZINBKT In-Ceiling Bracket 

HDCM1 Ceiling Mount 

HDXWM2 Wall Mount  

HDPRM2 Parapet/Flat Roof Mount  

HDXCMA1 Corner Mount Adapter for HDXWM2  

HDXPMA2 Pole Mount Adapter for HDXWM2  

Document 800-11874V5 – Rev A – 01/2015

Refer to the installation instructions included with the mounts for more detailed

instructions on installing the mount and camera. See the following sections for more

information on installing the HDZ series camera with the HDCM1, HDXWM2, and

HDPRM2 mounts.

Note If you are installing the camera with the HDZINBKT in-ceiling bracket,

follow the installation instructions included with the bracket.

Using Safety Cable During Installation

The HDZ Series camera includes an eyelet for attaching a safety cable to securely fix the

camera to the mounting structure. It is recommended that you install a safety cable (such

as a 3/32-in. [2.4 mm] plastic coated aircraft cable) to secure the camera to the building

structure. This will prevent the camera from falling during installation. The cable must be

strong enough to support the weight of the camera (4.9 lb [2.2 kg] for the indoor model,

5.7 lb [2.6 kg] for the outdoor model).

Installing an Indoor

Ceiling Mount (HDCM1)

The HDCM1 ceiling mount weighs 4 lb

(1.8 kg) and can be installed directly to a

load-bearing ceiling. HDCM1 has a

maximum load rating of 26 lb (11.7 kg)

and is for indoor use only.

1. Ensure that the ceiling can support

the combined weight of the camera

and the mount (at least 8.8 lb

[4.0 kg]).

2. Make a cable entry hole in the

ceiling.

3. Feed the cables through the mount,

leaving approximately 1 ft (0.3 m)

extending past the end of the mount.

Note If you are using the recommended

safety cable, feed it through the

mount and attach one end to the

camera eyelet and the other end

to the building structure.

4. Attach the mount to the ceiling using

appropriate hardware.

5. Screw the indoor mount kit to the

ceiling mount.

6. Connect the cables to the camera

(see Cable Connections, below). If

you are using a Micro SD card,

install it before connecting the

cables.

Note Check that the eyelet cable

connection is secure and carrying

all of the load of the camera after

making all cable connections.

7. Attach the camera to the mount kit,

and then tighten the security screw

on the top of the camera.

Installing an Indoor/Outdoor Wall Mount (HDXWM2)

The HDXWM2 wall mount weighs 3.2 lb (1.45 kg) and can be installed directly to a load-

bearing wall, or to a corner or pole using an appropriate adapter. The mount has a

maximum load rating of 26 lb (11.7 kg) and can be installed indoors or outdoors.

1. Ensure that the mounting surface can support the combined weight of the camera

and the mount (at least 8.9 lb [4.05 kg]).

2. If you are using a corner or pole adapter, feed the cables through the cable access

hole of the adapter, and then attach the adapter to the mounting surface using

appropriate mounting hardware.

3. Feed the cables through the mount, leaving approximately 1 ft (0.3 m) extending

past the end of the mount.

Optionally, you can feed the cables through the 0.75 in. (19 mm) conduit hole at the

base of the mount arm (see illustration).

Note If you are using the recommended safety cable, feed it through the mount and

attach one end to the camera eyelet and the other end to the building structure.

4. Attach the mount to the wall or, if applicable, to the adapter using appropriate

mounting hardware.

5. For outdoor wall mount installations, apply sealant (not supplied) to any gaps

between the mount and the mounting surface, and ensure that the conduit hole

plug is in place when the conduit hole at the base of the mount arm is not in use.

6. Screw the mount kit into the wall mount.

7. Connect the cables to the camera (see Cable Connections, below). If you are using

a Micro SD card, install it before connecting the cables.

Note Check that the eyelet cable connection is secure and carrying all of the load of the

camera after making all cable connections.

8. Attach the camera to the mount kit, and then tighten the security screw on the top of

the camera.

Note Optional: Use the lubricant on the dome cover’s rubber ring to make it easier to

re-attach to the housing and seal the PTZ dome cover and housing without water

coming in. Be careful to not get any lubricant on the dome as it may interfere with

viewing PTZ images.

Installing a Parapet/Flat Roof Mount (HDPRM2)

The HDPRM2 parapet/flat roof mount weighs 22 lb (10.2 kg) and can be installed directly

to a vertical (parapet) or horizontal (flat roof) load-bearing surface. The mount has a

maximum load rating of 20 lb (9.1 kg) and can be installed indoors or outdoors. The

mount can withstand winds up to 75 mph (121 km/h) when properly fastened to a support

structure.

1. Ensure that the mounting surface can support the combined weight of the camera

and the mount (at least 28 lb [12.8 kg]).

2. Feed the cables through the mount, leaving approximately 1 ft (0.3 m) extending

past the end of the mount.

Note If you are using the recommended safety cable, feed it through the mount and

attach one end to the camera eyelet and the other end to the building structure.

3. Attach the mount to the mounting surface using as many of the mounting holes as

possible (a minimum of five fasteners on each side of the mounting plate is

recommended).

HDZ Indoor Model Back Plate

Eyelet location on indoor dome back panel

Eyelet location on outdoor dome back panel

HDZ Outdoor Model Back Plate

Screw the

mount kit

onto the

ceiling

mount

Attach the

camera

body onto

the mount

kit

Tighten the screw at

the top of the camera

Feed cables

through the

mount kit

Screw the mount kit

onto the wall mount

Attach the

camera body

onto the mount

kit

Tighten the

screw at the

top of the

camera after

connecting the

three parts

19 mm (0.75 in.)

cable access

hole for surface-

mounted conduit.

Cable access hole

for field service.

Feed cables

through the

mount kit

4. Apply sealant (not supplied) to the bottom of the vertical pipe and around the bolt

holes to prevent water or other contaminants from entering the mount.

5. Screw the mount kit to the parapet/flat roof mount.

6. Connect the cables to the camera (see Cable Connections, below). If you are using

a Micro SD card, install it before connecting the cables.

Note Check that the eyelet cable connection is secure and carrying all of the load of the

camera after making all cable connections.

7. Attach the camera to the mount kit, and then tighten the security screw on the top of

the camera.

Note Optional: Use the lubricant on the dome cover’s rubber ring to make it easier to

re-attach to the housing and seal the PTZ dome cover and housing without water

coming in. Be careful to not get any lubricant on the dome as it may interfere with

viewing PTZ images.

Cable Connections

Before connecting the cables, take a minute to th the camera’s back familiarize yourself wi

plate connectors, switches, and buttons, as shown in the figures and table below.

Connecting Audio

Refer to the following figure and table when making audio connections to your camera.

Connecting Alarm Inputs/Outputs

Refer to the following figure and table when making alarm connections to your camera:

Connecting the Network Cable

To power the camera, either PoE or a 24 V AC power connection can be used. If using

PoE, either a switch or PoE injector meeting the PoE+ standard (30 W) or High Power

over PoE (60 W), depending on the model, must be employed (see table below).

Connect an Ethernet cable to the RJ45 connector on the back plate of the camera (see

figure above). The Ethernet cable should not be longer than 328 ft (100 m). After you have

connected the cable, check the status of the LED indicators on the RJ45 connector. (If the

LEDs are not lit, re-check the connection.)

• The green LED indicates a network connection.

• The orange LED indicates network activity.

Note You may need to use a crossover cable if you are connecting the camera directly

to a PC.

Connecting Power

Refer to the following figure and table when connecting power to your camera through

the main power adapter.

A ERJ45 connector Factory reset button

a.Press the factory reset button to restore the factory default settings to the camera.

BAlarm input/outputb

b.Alarm, power, and audio connections are made with removable connectors.

FAudio input/outputb

CPowerb GEyelet for attaching security cable

DMicro SD memory card slotc

c.It is recommend that you use a high quality micro SD card (up to 64 GB; microSDXC 64 GB

support tested with SanDisk SDXC 64 GB) that has a class 10 minimum write speed (8 GB

MLC/16 GB MLC or TLC/32 GB TLC). Insert the card before finishing camera installation.

The card must be formatted using the Honeywell Web GUI before it can be used for

recording.

Screw the mount kit onto

the parapet mount

Attach the

camera body to

the mount kit

Tightly fix the screw at the

top of the camera after

connecting the three parts

Feed cables

through the

mount kit

HDZ Indoor Dome Cameras

HDZ Outdoor Dome Cameras

HDZ Camera Model PoE Requirement

HDZ22HD(X), HDZ30(X), HDZ30HD PoE+ (30 W)

HDZ22HDE(X), HDZ30HDE, HDZ36E(X) PoE++ (60 W)

Pin Definition

1Line out

2GND

3Line in

1 2 3

Pin Definition Pin PinDefinition Definition

1 5 9Alarm Out NO 1 Alarm Out NO 2 Alarm In 4

2 6Alarm Out NC 1 Alarm Out NC 2 10 Alarm In 3

3 7Alarm Out COM 1 Alarm Out COM 2 11 Alarm In 2

4 8GND GND 12 Alarm In 1

1 2 3 4 5 6 7 8 9 10 11 12

Inputs (×4) 5 V, 4700 ohms, pull up

Outputs (×2) Relay output, 120 V AC/

30 V DC, 3 A MAX

Note Use alarm outputs for SELV

circuits only.

Pin Definition

124 V AC

2FG

324 V AC

123

Note Please use the minimum power adapter for:

HDZ30(X): 24 V AC, ~1.0 A MAX / PoE+, 21.0 W

HDZ36E(X): 24 V AC, ~3.3 A MAX / PoE++, 57.0 W

HDZ22HD(X), HDZ30HD: 24 V AC, ~1.3 A MAX /

PoE+, 25.5 W

HDZ22HDE(X), HDZ30HDE: 24 V AC, ~3.3 A MAX /

PoE++, 60.0 W

Important Note:

Regarding PoE Operation of models HDZ22HDE(X), HDZ36E(X) and

HDZ30HDE

A high power PoE injector capable of supplying at least 60 W is required for proper

operation of outdoor camera model HDZ22HDE(X), HDZ36E(X) and HDZ30HDE as PoE

to IEEE802.3af or IEEE802.3at will not support these models.

Product specificaties

Merk:	Honeywell
Categorie:	Bewakingscamera
Model:	HDZ22HD

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell HDZ22HD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Honeywell

Honeywell HC35WE5R3 Handleiding

20 December 2024

Honeywell Performance H4W8PER2V Handleiding

20 December 2024

Honeywell HDZ30A Handleiding

11 Juni 2023

Honeywell Performance HD31H Handleiding

7 Juni 2023

Honeywell HD50 Handleiding

2 Juni 2023

Honeywell Equip HDZ30 Handleiding

28 Mei 2023

Honeywell Performance HBW8PR2 Handleiding

28 Mei 2023

Honeywell HDZ36AEX Handleiding

28 Mei 2023

Honeywell Acuix HDV1NDFSW Handleiding

25 Mei 2023

Honeywell Enterprise HERC96T24S Handleiding

25 Mei 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Hikvision DS-2CE12KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE78D0T-LXTS/A Handleiding

18 December 2024

TP Link VIGI C450 Handleiding

18 December 2024

Hikvision DS-2CE76U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE78U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE16U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LSYE Handleiding

18 December 2024

Hikvision DS-2CE17U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE12KF3T-LSYE Handleiding

18 December 2024