Honeywell HD3VC4SHR Handleiding

Honeywell Bewakingscamera HD3VC4SHR

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell HD3VC4SHR (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Document 900.0824 -09/06 Rev - 1.01

3 Inch Dome Camera

HD3VC4SHR/HD3VC4SA/HD3VC4SHRX/HD3VC4SAX

Quick Install Guide

Warnings, Operating Notes

Installation and servicing should be performed

only by qualified and experienced technicians to

conform to all local codes and to maintain your

warranty.

WARNING! The use of CSA Certified/UL

Listed Class 2 power adapters is

required to ensure compliance

with electrical safety standards.

WARNING! To reduce the risk of fire or

electric shock, do not expose this

product to rain or moisture.

WEEE (Waste Electrical and Electronic

Equipment). Correct disposal of this product

(applicable in the European Union and other

European countries with separate collection

systems). This product should be disposed of,

at the end of its useful life, as per applicable

local laws, regulations, and procedures.

FCC Compliance Statement

Information to the User: This equipment has

been tested and found to comply with the limits

for a Class A digital device. Pursuant to Part 15

of the FCC Rules, these limits are designed to

provide reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

Caution Changes or modifications not

expressly approved by the party

responsible for compliance could void

the user’s authority to operate the

equipment.

This Class A digital apparatus complies with

Canadian ICES-003.

Manufacturer’s Declaration of

Conformance

The manufacturer declares that the equipment

supplied with this guide is compliant with the

essential protection requirements of the EMC

directive 89/336/EEC and the Low Voltage

Directive LVD 73/23 EEC, conforming to the

requirements of standards EN 55022 for

emissions.

Operating Notes

Power Supply

This dome camera can operate on 24 VAC

or 12 VDC.

Operating Conditions

• Avoid viewing very bright objects (example,

light fixtures) for extended periods.

• Avoid operating or storing the unit in the

following locations:

• Extremely humid, dusty, hot/cold

environments (where the operating

temperature is outside the

recommended range of 14°F to 122°F

[-10°C to +50°C])

• Close to sources of powerful

electromagnetic radiation, such as

radio or TV transmitters

• Close to fluorescent lamps or objects

reflecting light

• Under unstable light sources (may

cause flickering)

Introduction

The unobtrusive, compact design of the

HD3VC4S Series 3 Inch Dome Camera is ideal

for indoor installations in commercial and

residential environments.

Before You Begin

Unpack Everything

Check that the items received match those listed

on the order form and packing slip. The

HD3VC4S Series Camera packing box should

include, in addition to this Install Guide:

• One fully assembled camera

• One hardware kit

• One 2nd video monitor output cable

• One mounting template

If any parts are missing or damaged, contact the

dealer you purchased the camera from or call

Honeywell Customer Service.

Installation

The HD3VC4S Series is a fully-integrated

enclosure with camera and lens.

Figure 1 Camera Parts

Note See Figure 5 for an explanation of the

camera board settings.

Removing the Dome Cover

1. Gently turn the dome cover (#5 on

Figure 2) counter-clockwise to unlock and

pull free of the housing.

2. Remove the inner liner (#4) by gently

pulling it free of the two notches (#2) in the

housing (#1).

3. Set the dome (and liner) aside.

Figure 2 Dome Cover Removal

Connecting the Wiring

Follow Figure 1 to connect the video output

connector (a) and 24 VAC/12 VDC power

connector (b).

Caution For DC power supply use, make sure

the polarity is correct to avoid

malfunction and/or camera damage.

Mounting the Camera

1. Place the mounting template (supplied) on

the mounting surface and mark the holes

(see Figure 3).

2. Drill two holes, then insert the screw

anchors into the holes.

3. Secure the camera housing to the wall/

ceiling with the TP4 x 15 mm tapping

screws supplied.

Note Depending on the material of your

mounting surface, you may require

different screws and anchors than

those supplied.

Figure 3 Camera Installation

Adjusting the Camera Position

The HD3VC4S Series camera has three axes for

positioning the camera. While monitoring the

picture on the monitor, adjust the camera

position as follows:

Horizontal Adjustment Rotate the 3D

assembly in the base. Do not turn the assembly

more than 360° as this may cause the internal

cables to twist and disconnect or break.

Vertical Adjustment After loosening the

thumbnuts, position the camera as desired, then

finger-tighten the thumbnuts to set the position.

Horizontal Rotation For Wall Mount and Tilted

Ceilings Rotate the lens base (maximum 360°)

until you are satisfied with the field of view.

Figure 4 Camera Adjustment

Adjusting the Lens

1. Loosen the Zoom lever (#3) counter-

clockwise a little, then rotate the Zoom

lever and determine the image view.

2. Loosen the Focus lever (#4) counter-

clockwise a little, then adjust the focus for

optimum picture sharpness.

3. Re-tighten the Zoom lever and Focus lever

after adjustment.

Note It is important that you lock the zoom

and focus levers after making

adjustments. This will avoid the

positions moving (for example, from

temperature changes or vibrations).

Optional Camera Settings

See Figure 5 for location on the camera board of

the camera adjustment functions described

below.

Figure 5 Camera Adjustment Functions

Note Please use the supplied DC Iris and

Line lock adjustment tool to adjust

picture brightness and phase

adjustment.

Picture Brightness Use the LEVEL screw (#1)

to compensate for the iris level. L (low) makes

the picture darker. H (high) makes the picture

brighter.

Phase Adjustment Use the V Phase

Adjustment Pot (#2) to adjust the phase

difference between cameras. Make sure Switch

4 is ON to activate the Line lock function (AC

operation only).

DIP Switches Set the DIP switches (#3) to

activate or deactivate the following functions:

Document 900.0824 - 09/06 - Rev 1.01

RISK OF

ELECTRIC SHOCK

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER.

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

THIS SYMBOL INDICATES

THAT DANGEROUS VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS

PRESENT WITHIN THE UNIT.

THIS SYMBOL INDICATES THAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANY THIS UNIT.

CAUTION

Please read this guide carefully before

you install the HD3VC4S Series 3 Inch

Dome Camera. Keep this guide for

future reference.

1 — Legend

1Conduit hole used for surface run power/video

connector

2Camera housing

3Dome cover

4Zoom lever

5Focus lever

aVideo output connector

b24 VAC/12 VDC power input connector

(red +, black -)

2 — Legend

1Camera housing

2Notches (x2)

3Tilt adjustment bracke

and thumbnuts

4Inner liner

5Dome cover

M o u n t in g T e m p la t e

L o g o D i r e c t io n

MON

1:B LC

2:A GC

3:D C/AES

4:L L

1 2 3 4

OFF

LEVEL

H L

V P H A S E+ -

TOP

3 — Legend

1Screw anchors (x2), supplied

2Mounting template

3TP4 x 15 mm tapping screws (x2) supplied

Switch Description

1 BLC (Backlight Compensation). Set to ON to

have the camera adjust the exposure to

compensate for situations where the subject is lit

from behind. The factory default setting is OFF.

2 AGC (Automatic Gain Control). Set to ON

(default) to have the camera adjust the picture

for low light conditions.

3 DC/AES Mode. Leave in ON position only.

4 LL (Line Lock). Set the camera synchronization

to internal or line lock (line lock is only available

with 24 VAC). The factory default setting is OFF.

4 — Legend

1Tilt adjustment bracket and thumbnuts (x2)

for vertical adjustment

2Axis ring for horizontal rotation for wall

mount and tilted ceilings

3Zoom lever

4Focus lever

5Rotate 3D assembly in base for horizontal

adjustment

L EV E L

V PHA S E

+ -

1 : B L C

2 : AG C

3 : D C /AE S

4 : L L

1 2 3 4

OF F

M O N

LEVEL

H L

V P HA S E

+ -

MON

1:BL C

2:AG C

3 :DC / A ES

4:LL

1 2 3 4

O N

O F F

TOP

5 — Legend

1LEVEL adjustment pot (Iris level)

2V Phase adjustment pot (24 VAC only)

3Mode setting DIP switches

4Monitor out

5Camera mounting holes

www.honeywellvideo.com

+1.800.796.CCTV (North America only)

HVSsupport@honeywell.com

900.0824 - 09/06 - Rev 1.01

permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However,

Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained

herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.

Attaching the Dome Cover

To attach the dome cover, follow Figure 2:

1. Use a soft, lint-free cloth to wipe the dome

cover clean and remove fingerprints.

2. Attach the inner liner (#3) to the Tilt

adjustment thumbnuts (#2). Push down

until it clicks into place.

3. Place the dome (#4) on the unit. Make

sure all three dome tabs (#5) are inside the

housing opening.

4. Turn the dome gently clockwise until it

locks in place.

Routine Maintenance

• The dome cover is an optical part. Use a

soft, dry cloth to remove any fingerprints or

dust.

• Clean the camera housing with a soft, dry

cloth. For more stubborn stains, use a cloth

dampened with a small quantity of neutral

detergent, then wipe dry.

Caution Do not use volatile solvents such as

alcohol, benzene or thinners to avoid

damaging the surface finish.

Cable Guidelines

Product Dimensions

Figure 6 Camera Dimensions

Warranty and Service

Subject to the terms and conditions listed on the

Product warranty, during the warranty period

Honeywell will repair or replace, at its sole

option, free of charge, any defective product

returned prepaid.

In the event you have a problem with any

Honeywell product, please call Customer

Service for assistance or to request a Return

Merchandise Authorization (RMA) number.

Call 1.800.796.CCTV (North America only).

Be sure to have the model number, serial

number, and the nature of the problem available

for the technical service representative.

Prior authorization must be obtained for all

returns, exchanges, or credits. Items shipped

to Honeywell without a clearly identified

Return Merchandise Authorization (RMA)

number may be refused.

Europe and United Kingdom

For warranty information please contact your

Honeywell dealer.

Specifications Contact Information

Honeywell Video Systems (Head Office)

2700 Blankenbaker Pkwy, Suite 150

Louisville, KY 40299, USA

www.honeywellvideo.com

℡ +1.800.796.2288

Honeywell Security Australia Pty Ltd.

Unit 5, Riverside Centre, 24-28 River Road West

Parramatta, NSW 2150, Australia

www.ademco.com.au

℡ +61.2.8837.9300

Honeywell Security Asia Pacific

33/F Tower A, City Center, 100 Zun Yi Road

Shanghai 200051, China

www.security.honeywell.com/cn

℡ +86 21.2527.4568

Honeywell Security Asia

Flat A, 16/F, CDW Building, 388 Castle Peak Road

Tsuen Wan, N.T., Hong Kong

www.security.honeywell.com/hk

℡ +852.2405.2323

Honeywell Security France

Parc Gutenberg, 8, Voie La Cardon

91120, Palaiseau, France

www.honeywell.com/security/fr

℡ +33.01.64.53.80.40

Honeywell Security Italia SpA

Via Treviso 2 / 4

31020 San Vendemiano

Treviso, Italy

www.honeywell.com/security/it

℡ +39.04.38.36.51

Honeywell Security Spain

Mijancas 1. 3a Planta

P.Ind. Las Mercedes

28022 Madrid, Spain

www.security.honeywell.com/es

℡ +34.902.667.800

Honeywell Security Nederland

Netwerk 121

1446 WV Purmerend, Netherlands

www.SecurityHouse.nl

℡ +31.299.410.200

Honeywell Video Systems UK Ltd.

Aston Fields Road, Whitehouse Ind Est

Runcorn, Cheshire, WA7 3DL, UK

www.honeywellvideo.com

℡ +0844.8000.235

Honeywell Security South Africa

Unit 6 Galaxy Park, 17 Galaxy Avenue

Linbro Park, P.O. Box 59904

2100 Kengray, Johannesburg, South Africa

www.honeywell.co.za

℡ +27.11.574.2500

Honeywell Security Germany

Johannes-Mauthe-Straße 14

D-72458 Albstadt, Germany

www.honeywell.com/security/de

℡ +49.74 31.8 01.0

Honeywell Security Poland

Chmielewskiego 22a, 70-028

Szczecin, Polska

www.ultrak.pl

℡ +48.91.485.40.60

Honeywell Security Czech Republic

Havránkova 33, Brno

Dolní Heršpice, 619 00, Czech Republic

www.olympo.cz

℡ +420.543.558.111

Honeywell Security Slovakia Republic

Vajnorskà 142, 83104 Bratislava

Slovakia

www.olympo.sk

℡ +421.2.444.54.660

Maximum Power Supply Cable Length (feet/meters)

Cameras With AC/DC Power Supplies

Wire gauge

Total

load

Power

supply

24 AWG 22 AWG 18 AWG 16 AWG

High

Res

12 VDC

15 VDC

24 VAC

89/27

348/106

991/302

148/45

561/171

1601/488

374/114

1427/435

4061/1238

597/182

2273/693

6462/1970

Std Res 12 VDC

15 VDC

24 VAC

236/72

420/128

1155/352

384/117

679/207

1866/569

977/298

1729/527

4736/1444

1555/474

2752/839

7541/2299

Caution Calculations are based on an unregulated linear

power supply, which would be the worst case. Using a regulated

or switching power supply can increase the cable distance.

Honeywell recommends using a CSA Certified/UL listed Class 2

power adapter to ensure compliance with electrical safety

standards.

Maximum Video Coaxial Cable Length (feet/meters)

Cable type RG-59 RG-6 RG-11

Wire gauge 23 AWG* 18 AWG* 14 AWG*

Maximum length (feet/meters) 750/229 1500/457 2000/610

* Copper clad steel core, 95% braided shield

Legend

1Camera housing

Tilt adjustment

bracket and

thumbnuts

3Inner liner

4Dome cover

5Dome tabs (x3)

4.33” (110 mm)

3.91” (96.3 mm)

3.27” (83 mm)

0.2” (5 mm)

diameter

Video Signal Specifications

Video Standard: NTSC, PAL NTSC, PAL

High Res Standard Res

Scanning System: 525 lines, 2:1 interlace (NTSC)

625 lines, 2:1 interlace (PAL)

Image Sensor: 1/3” Interline Transfer CCD

Number of Pixels

(H x V):

768 x 494 (NTSC)

752 x 582 (PAL)

510 x 492 (NTSC)

500 x 582 (PAL)

Minimum

Illumination:

0.6 lux @ F1.3 0.2 lux @ F1.3

(AGC on, 50 IRE)

Horizontal

Resolution:

540 TVL 350 TVL

Video Output: 1.0 Vp-p @ 75 Ohms

S/N Ratio: 50 dB (AGC Off)

Sync System: 12 VDC: Internal, 24 VAC: Line lock

Auto Gain Control: On/off, switchable

BLC: On/Off, switchable

AI/AES Selection: On/off, switchable

Automatic Electronic

Shutter:

1/60 - 1/100,000 sec (NTSC)

1/50 - 1/100,000 sec (PAL)

Lens Type: 2.8 mm to 10 mm Vari-focal Auto Iris,

F1.3

Lens Iris Control: Direct Drive (DC) AI

Angle of View (Lens):

Wide

Tele

129.0° (D), 100.2° (H), 73.3° (V)

34.3° (D), 27.4 (H), 20.5° (V)

Focal Length: f = 2.8 mm to 10 mm

White Balance: ATW

Gamma: 0.45

Electrical Specifications

Input Voltage: 12 VDC/24 VAC

Input Voltage Range: 11 to 16 VDC

17 to 28 VAC

Power Consumption: 3.5 W (max)

Mechanical

Dimensions

(W x H):

4.33” x 3.91” (110 mm x 96.3 mm)

Weight:

Net

Shipping

.66 lb (.3 Kg)

1.32 lb (.6 Kg)

Construction: Housing and dome: Polycarbonate

Environmental

Temperature:

Operating

Storage

14°F to 122°F (-10°C to 50°C)

-4°F to 140°F (-20°C to 60°C)

Relative Humidity: 0% to 90%, non-condensing

Regulatory

Emissions: FCC, CE (EN55022)

Immunity: CE (EN50130-4)

Safety: UL2044 a, EU: 73/23/EEC LVD

a Applies only to HD3VC4SHR and

HD3VC4SA models.

Product specificaties

Merk:	Honeywell
Categorie:	Bewakingscamera
Model:	HD3VC4SHR

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell HD3VC4SHR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Honeywell

Honeywell HC35WE5R3 Handleiding

20 December 2024

Honeywell Performance H4W8PER2V Handleiding

20 December 2024

Honeywell HDZ30A Handleiding

11 Juni 2023

Honeywell Performance HD31H Handleiding

7 Juni 2023

Honeywell HD50 Handleiding

2 Juni 2023

Honeywell Equip HDZ30 Handleiding

28 Mei 2023

Honeywell Performance HBW8PR2 Handleiding

28 Mei 2023

Honeywell HDZ36AEX Handleiding

28 Mei 2023

Honeywell Acuix HDV1NDFSW Handleiding

25 Mei 2023

Honeywell Enterprise HERC96T24S Handleiding

25 Mei 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Hikvision DS-2CE12KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE78D0T-LXTS/A Handleiding

18 December 2024

TP Link VIGI C450 Handleiding

18 December 2024

Hikvision DS-2CE76U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE78U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE16U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LSYE Handleiding

18 December 2024

Hikvision DS-2CE17U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE12KF3T-LSYE Handleiding

18 December 2024