Honeywell HBD7S Handleiding

Honeywell Bewakingscamera HBD7S

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell HBD7S (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 74 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
HBD7S(X) Bullet Camera Quick Installation Guide
Document 800-15430 – Rev A – 07/2013
Introduction
Thank you for purchasing a Honeywell HBD7S(X) bullet camera. Follow the instructions in this guide to
install your camera. To configure the camera settings, refer to the HBD7S(X) Bullet Ca
mera Configuration
Guide.
Important Safety Instructions
• Read and keep these instructions.
• Please ensure that your installation area can safely support the weight of the camera.
• Do not aim the camera toward an extreme light source to prevent damage to the CCD.
• Do not touch the camera lens or bezel (front glass plate).
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments (where the
operating temperature is outside the recommended range of 14°F to 122°F [–10°C to 50°C]).
Dimensions
Installing the Camera
Before You Begin
Before you begin installing the camera, check that you have received all of the parts listed below.
If any parts are missing or damaged, contact your dealer immediately.
Connecting the Camera Cable
1. Connect the camera’s video output to the video input on your monitor or DVR.
2. Connect the camera’s power input to a 12 V DC or 24 V AC power supply.
WARNING
Installation and servicing should be performed only
by qualified and experienced technicians to conform to all local
codes and to maintain your warranty.
WARNING
This device is configured for 12 V DC or 24 V AC
operation. Do not connect to a higher voltage. Use only with NTRL-
approved Class 2 power supplies.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
DO NOT OPEN
RISK OF ELECTRIC SHOCK
• Camera (cable included)
• Manuals
• Video test cable
• DC power pigtail
• Mounting plate
• Focus and zoom adjustment tool
• 4 socket head cap screws
• 4 pan head screws
• 1 hex key
8.54″ (217 mm)
4.84″ (123 mm)
3.68″ (93.5 mm)
3.27″ (83 mm)
1
BNC Video Out (Yellow)
DC Power Jack (Red)
www.honeywell.com/security
+1 800 323 4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
Document 800-15430 – Rev A – 07/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without wri
tten permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
HBD7S(X) Bullet Camera Quick Installation Guide
Mounting the Camera
1. Using a Phillips driver (not su to the mounting surface (with the pplied), attach the mounting plate
foam side facing the wall) using the four supplied 1-inch (25.4 mm) pan head screws,
2. Using the supplied hex key, attach the camera and bracket to the mounting plate using the four
supplied 3/8-inch (9.52 mm) socket head cap screws. Ensure that the notch in the bracket base is
facing down.
Positioning the Camera
After the camera is mounted, adjust the multidirectional bracket to set the camera’s field of view.
There are three adjustment points.
1. Loosen the adjustment screws with the supplied hex key, move the camera to the desired position,
and then tighten the screws.
2. Loosen the adjustment ring, move the camera to the desired position, and then tighten the ring.
Setting the Focus and Zoom
The focus and zoom controls are located on the underside of the camera.
1. Unscrew the cap on the underside of the camera to access the
focus and zoom controls.
2. Connect the supplied video test cable to VIDEO TEST and
connect the other end to a portable service monitor.
3. Adjust the camera’s focus and zoom settings using the supplied
tool. If the focus and zoom adjustment screws do not move
freely, loosen the lock screw.
4. Tighten the lock screw to prevent the focus and zoom settings
from changing as a result of camera vibration.
Configuring the Camera
The camera is programed using on-screen display (OSD) menus.
These menus are controlled by the built-in OSD joystick on the underside of the camera
(next to the focus and zoom controls).
• Press down and hold the OSD joystick for two seconds to
bring up the OSD main menu on the connected monitor.
• Push the joystick up or down to move up or down through
the list of menu options.
• Press down on the joystick to to enter a submenu (

) or
to execute (set) a menu selection.
• Push the joystick left or right to change a menu setting.
360° 360°
180°
Adjustment
screw
Adjustment
screw
Adjustment
ring
2
ZOOM FOCUS
LOCK
SET UP
VIDEO TEST
LENS
DC
MANUAL
EXPOSURE
SHUTTER
AGC
SENSE-UP
BLC
D-WDR
RETURN
WHITE BALANCE
ATW
AWB
AWC->SET
MANUAL
DAY&NIGHT
COLOR
B/W
AUTO
EXT
3DNR
OFF
ON
SPECIAL
CAM TITLE
D-EFFECT
MOTION
PRIVACY
DEFECT
DEFOG
RETURN
ADJUST
SHARPNESS
MONITOR
RESET
FACTORY
RETURN
EXIT
3
SET UP

Product specificaties

Merk: Honeywell
Categorie: Bewakingscamera
Model: HBD7S

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell HBD7S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Bewakingscamera Honeywell

Honeywell

Honeywell HDZ30A Handleiding

11 Juni 2023
Honeywell

Honeywell Performance HD31H Handleiding

7 Juni 2023
Honeywell

Honeywell HD50 Handleiding

2 Juni 2023
Honeywell

Honeywell Equip HDZ30 Handleiding

28 Mei 2023
Honeywell

Honeywell Performance HBW8PR2 Handleiding

28 Mei 2023
Honeywell

Honeywell HDZ36AEX Handleiding

28 Mei 2023
Honeywell

Honeywell Acuix HDV1NDFSW Handleiding

25 Mei 2023
Honeywell

Honeywell Enterprise HERC96T24S Handleiding

25 Mei 2023
Honeywell

Honeywell HCS544 Handleiding

19 Mei 2023
Honeywell

Honeywell HC30W45R3 Handleiding

16 Mei 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Provision ISR

Provision ISR I3-350IP5SMVF Handleiding

20 November 2024
Provision ISR

Provision ISR I2-350A-28 Handleiding

20 November 2024
Provision ISR

Provision ISR I4-350A-MVF Handleiding

20 November 2024
Canon

Canon PowerShot GOLF Handleiding

20 November 2024
Flir

Flir FH-Series Handleiding

20 November 2024
EtiamPro

EtiamPro CCTVPROM23 Handleiding

17 November 2024
EtiamPro

EtiamPro CCTVPROM20W Handleiding

17 November 2024
Leviton

Leviton 68A02-2 Handleiding

17 November 2024
Reolink

Reolink RLK8-800D4 Handleiding

16 November 2024
Reolink

Reolink RLK16-800D8 Handleiding

16 November 2024