Honeywell HBD3PR2 Handleiding

Honeywell Bewakingscamera HBD3PR2

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell HBD3PR2 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

H BD3PR2 True Day/Night Indoor/Outdoor IR

Bullet IP Camera Regulatory Statements

Information to the User: This has equipment been and tested found to comply with the limits afor

Class B digital device, pursuant to part 15 of the Rules. FCC These limits are designed to provide

reasonable against protection harmful interference a in residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that a particular interference will not occur in installation.

Quick Installation Guide

Document 800 2123 10/2015- 3 — A– V1 Rev

Thank you for purchasing a HBD3PR2 c . amera

Follow the

instructions in this guide and to install

log to

your camera. For instructions on

configuring the

camera, refer to the Performance

Series IP

Cameras User Guide on the software

and

documentation CD that came with your

camera. If

you require additional assistance,

please call the

number shown below.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment is and off on, the user encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the the separation between equipment and receiver.

Connect the equipment into an outlet a that on circuit different from to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Cautions and Warnings

•

Note Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This B Class digital apparatus complies Canadian with ICES- 003.

Cet appareil numérique de la B à Classe est conforme la - Canada. norme NMB 003 du

Important Safeguards

WARNING

•

Read and keep these instructions.

Do not aim the camera toward a bright light source for extended periods to prevent damage to

the imager. Avoid operating the unit under or close to unstable light sources (may cause

flickering), or close to fluorescent lamps or objects reflecting light.

Do not touch the camera lens.

Do not drop the camera or subject it to physical shock.

Do not use a strong or abrasive detergent when cleaning the camera.

Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the

operating temperature is outside the recommended range of - 4°Fto 140°F (– 20°C to 60°C).

To ensure compliance with electrical safety standards this product is

intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,

on the unit, output rated 12 V DC, minimum 0.33A, Tma=60Deg.C or from Power over

Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE

802.3af PoE standard. •

•

The Ethernet connection is not intended to be connected to exposed (outside plant)

networks. Do not connect two power sources to the camera at the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam. Note

Do not apply power to the completing installation. camera before

Note

Confirm the installation surface can support at least three times the weight of the camera plus

the bracket.

Document 800 2123 /2015- 3 – A – V1 Rev 10 1

H BD3PR2 True Day/Night Indoor/Outdoor IR Bullet IP Camera

Before You Begin

Before you begin, that check you all have received of the parts listed below. If any parts are missing

or your damaged, contact dealer immediately.

•

Camera

Documentation CD

Quick install guide

Allen key (L- wrench)

•

Self- 3)tapping screws (×

Plastic wall anchors 3)(×

Mounting template

b. Insert the microSD card into the microSD card slot as

shown in the picture at right.

c. Replace the control panel.

2. Connect the camera with the Ethernet cable and the power

cable.

Required tools:

•

A Phillips screwdriver

A drill with an appropriately- sized drill bit for pre- drilling holes for the screw anchors.

CAUTION

Installation and servicing should be performed only by qualified

and experienced technicians to conform to all local codes and to maintain your

warranty.

Aiming the Camera

Use the supplied Allen key to loosen the adjusting screws

on the bracket arm.

2. Set the camera to the desired position.

3. Tighten the adjustment screws.

Preparing the Mounting Surface

1. Inspect the site where you want to install the camera. The mounting surface must be

flat and capable of supporting at least three times the weight of the camera.

2. Remove the backing from the mounting template sticker and affix the sticker to the

mounting surface.

Note If you are using the side exit for the cable, no te the orientation of the cab le exit

no tch. In out oor d ins ltal ati no rons the tch should point downwa ds to prevent wat fr er om

enteri ng the ca i mera hous ng.

Document - 3 – – 800 2123 V1 Rev A 10/2015

© 5 201 Honeywell this publication International Inc. All rights reserved. No part of may be reproduced by any means without written permission fro m Honeywell. The information in this publication is believed to be accurate in all respects. However,

Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to to Revisions editions change without notice. or new this publication may be issued such to incorporate changes.

3. Dr ho at lo tions a till three screw les the ca indic ted on he moun ng tem te ic r ti pla st ke and

in t e th e a ic an in holeser th re suppl plied st chors the s.

4. If you nt to sto b i wa re the ca les nside the wall drill hole i or ceil ng, a ca i o tionat the ble ex t p si

on i p the mount ng tem late and then pull the thr s cable ough the hole.

Mounting the Camera

1. If local storage is needed, i m nsert a icro SD card into the micro SD card slot

according to the following steps:

a. Use a Phillips screwdriver (not supplied) and remove the control panel cover

on the outside of the camera.

Adjusting the Zoom and Focus Settings

The c connected to a PoE port of the Honeywell Embedded NVR can be configured ameras

with the NVR directly.

To log on to the camera with a PC, perform the following steps:

1. Install the Honeywell Config Tool from the software and the documentation CD, find the

camera and open the web browser with the Honeywell Config Tool

2. Log on to the camera as the -admin user. The default user name is admin (case sensitive)

and the default password is 1234.

3. Go to Setup   Camera Conditions Zoom and Focus. The following panel appears:

• Click Zoom in – + or Zoom out to zoom in or out.

• Click Near – + or Far to focus near or far, or click Auto Focus to enable auto focus.

a. Connect one end of the Ethernet cable to the RJ- 45 port on the camera.

b. (PowerIf the other end of the Ethernet cable is NOT connected to a PoE - -over

Ethernet) switch or NVR, connect the power connector of the camera to a 12 V

DC power source.

3. Attach the camera assembly to the mounting surface using the supplied screws.

Product specificaties

Merk:	Honeywell
Categorie:	Bewakingscamera
Model:	HBD3PR2
Kleur van het product:	Wit
Gewicht:	650 g
Diepte:	214.8 mm
Hoogte:	90.4 mm
Soort:	IP-beveiligingscamera
Internationale veiligheidscode (IP):	IP66
Ondersteunde mobiele besturingssystemen:	Android, iOS
Maximale capaciteit van de geheugenkaart:	128 GB
Vormfactor:	Rond
Automatisch scherpstellen:	Ja
Ondersteuning voor plaatsing:	Binnen & buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Muur
Ondersteunde video-modi:	720p, 1080p
Maximum resolutie:	2304 x 1296 Pixels
Totaal aantal megapixels:	3 MP
Type stroombron:	Power over Ethernet (PoE)
Stroomuitvoer (volt):	12
Minimale belichting:	0.1 Lux
Aantal cameras:	1
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	MicroSDHC
Nachtvisie:	Ja
LED-type:	IR
HTTPS-encryptie:	Ja
Zoomcapaciteit:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Focus:	Gemotoriseerd
Brandpuntbereik:	2.7 - 12 mm
Vermogensverbruik (max):	8.5 W
Certificering:	FCC
Volledige HD:	Ja
Omvang optische sensor:	1/3 "
Type beeldsensor:	CMOS
Camera sluitertijd:	1/100000 s s
Witbalans:	Auto, Manual
Ondersteunde grafische resoluties:	352 x 240,352 x 288,704 x 480,704 x 576,1280 x 720 (HD 720),1920 x 1080 (HD 1080)
Plug and play:	Ja
Bekabelingstechnologie:	10/100Base-T(X)
Netwerkstandaard:	IEEE 802.3af
Ondersteunde beveiligingsalgoritmen:	802.1x RADIUS
Aantal gebruikers:	20 gebruiker(s)
Veiligheidsfunties:	Waterbestendig
Maximaal 30 frames per seconde:	30 fps
Op afstand bedienbaar:	Ja
Progressive scan:	Ja
Quality of Service (QoS):	Ja
Power over Ethernet (PoE):	Ja
Type sterkteregeling:	Automatisch/handmatig
Dag/nacht modus:	Ja
Maximum aperture number:	1.4
Bewegingssensor:	Ja
Nachtkijker afstand:	30 m
Achtergrondverlichting compensatie:	Ja
Aantal effectieve pixels (H x V):	2304 x 1296 Pixels
Highlight Compensation (HLC) (compensatie voor sterke belichting):	Ja
Bedrijfstemperatuur (T-T):	-30 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 100 procent
Kijkhoek lens, horizontaal:	86 °
Digital Wide Dynamic Range (DWDR):	Ja
Smart IR:	Ja
3D-geluidsreductie:	Ja