Honeywell 3350D Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell 3350D (14 pagina's) in de categorie Kluis. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/14
ATTENTION!
This Honeywell Executive Safe includes a new
Dual User Code Digital Lock. This update replaces
the User Code Programming Instructions located
on Page 3 of the Owner’s Manual for Executive
Safe Models 3014D, 3018D, 3024D 3032D, ,
3114D, 3118D, 3124D, 3132D, 3310D, 3330D,
3350D, 3410D, 3430D, 3450D&
DUAL DIGITAL LOCKUSER CODE
PRIMARY & SECONDARY USER CODE
PROGRAMMING INSTRUCTIONS
IMPORTANT UPDATE!
PRIMARY & SECONDARY USER CODES
Your new safe is equipped with a digital lock that can be operated with two separate user
codes. You will need to program codes with your own 3 these user -8 digit user codes. It is
recommended that you record your new codes and keuser ep in a secure location away
from the safe. You must program the Primary user code first. After the Primary user code
is programmed and tested you can then proceed to program the Secondary user code.
PRIMARY USER CODE
UNLOCK AND OPEN SAFE
IMPORTANT: Always make sure that the spindle handle is turned counterclockwise to the
left before entering user code.
1. Open your new safe by entering 1-2-3-4-5-6 # followed by the key on the keypad.
2. After user code is entered, the keypad will beep once and e green LED will light upth . !
3. Turn the spindle handle to the right (clockwise) to open. !
NOTE: You must open the safe within 5 seconds or .the safe will relock !
PROGRAM PRIMARY THE USER CODE
1. With door open, locate and press the red reset button
located on the inside edge of the door (see illustration), the
keypad will beep twice and the green LED will light up.
2. Enter a new 3-8 digit Primary user code followed by the #
key. The green LED will light up and the keypad will beep.
3. 8 digit Immediately re-enter the new 3- user code a second
time followed by the # key and the green LED will flash
twice and the keypad will beep twice.
4. This new Primary user code is now active.
TEST THE PRIMARY USER CODE
1. With door open, rotate handle counterclockwise to put door bolts in lock position.
2. Enter the new Primary 3-8 digit user code followed by the #key. The green LED will
light up and the keypad will beep.
3. R otate handle clockwise within 5 seconds.the spindle
4. The lock bolts should recede into the unlocked position when the handle is turned.
RE NEW PRIMARY USER CODEPROGRAM A
In the future, this user code can always be changed by opening the safe and using the
reset button.
1. Once the safe door is open, locate and press the small reset button located on the
inside edge of the door , the keypad will beep twice and the green LED will light up.
2. Enter a new 3-8 digit Primary user code followed by the #key, the green LED will
again light up and the keypad will beep.
3. 8 digit Immediately re- enter the new 3- user code a second time followed by the #key
and the green LED with flash twice and the keypad will beep twice.
4. This new Primary user code is now active and the old Primary code is deleted.user
1
SECONDARY USER CODE
PROGRAM THE SECONDARY USER CODE
Once you have successfully programmed the Primary user code, you can proceed to
programming the Secondary user code. The Secondary user code is programmed using
the Digital Keypad and it is not necessary to open the safe to proceed.
1. Using the keypad, press the
!
!
!
!! !
!
!
!! !
!
!
!! button twice ( - )
2. Enter the factory default user code 1-2-3-4-5-6 followed by the #key into the keypad.
3. The green LED with light up once and the keypad will beep twice.
4. Enter a new 3-8 digit Secondary user code followed by the #key and the green LED
will again light up and the keypad will beep.
5. 8 digit Immediately re-enter the new 3- Secondary user code a second time followed
by the # key and the green LED will flash twice and the keypad will beep twice.
6. After the new secondary user code is programmed, the factory preset code will be user
erased and the safe can only be unlocked using your new Primary or Secondary user
codes.
IMPORTANT: To change the secondary user user code, the current code will be
required. For this reason, it is very important that it is recorded and kept in a
secure location away from the safe.
TEST THE SECONDARY USER CODE
1. With door open, rotate handle counterclockwise to put door bolts in lock position.
2. Enter the new Secondary3-8 digit user code followed by the key. The green LED #
will light up and the keypad will beep.
3. Rotate handle clockwise within 5 seconds.
4. The lock bolts should recede into the unlocked position when the handle is turned.
REPROGRAM NEW USER CODEA SECONDARY
1. Using the keypad, press the - )
!
!
!
!! button twice (!
!
!
!! !
!
!
!!
2. Enter the current 3-8 digit Secondary user code followed by the # key into the keypad.
3. The green LED with light up once and the keypad will beep twice.
4. Enter a new 3- #8 digit secondary user code followed by the key and the green LED
will again light up and the keypad will beep.
5. 8 digit Immediately re-enter the new 3- secondary user code a second time followed by
the # key and the green LED will flash twice and the keypad will beep twice.
OPENING/CLOSING SAFE WITH USER CODES
1. Make sure the spindle handle is positioned to the left and enter your new user code
into the keypad followed by the # key.
2. The keypad will beep once, green LED will light up and the lock will click. Turn the
handle clockwise to the right to open the safe.
3. To lock, close the door and turn the spindle handle counterclockwise to the left.
2
Product specificaties
| Merk: | Honeywell |
| Categorie: | Kluis |
| Model: | 3350D |
Heb je hulp nodig?
Als je hulp nodig hebt met Honeywell 3350D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kluis Honeywell
16 April 2024
11 Maart 2024
11 Maart 2024
11 Maart 2024
11 Maart 2024
27 Februari 2024
18 December 2023
18 December 2023
18 December 2023
18 December 2023
Handleiding Kluis
- Kluis Philips
- Kluis Abus
- Kluis Avanti
- Kluis Burg-Wachter
- Kluis Dometic
- Kluis Duralock
- Kluis EasySafe
- Kluis Ferm
- Kluis Filex
- Kluis FireKing
- Kluis First Alert
- Kluis Fluke
- Kluis Hama
- Kluis Handson
- Kluis M-Locks
- Kluis Master Lock
- Kluis Nauta
- Kluis Nedis
- Kluis Perel
- Kluis Phoenix
- Kluis Protector
- Kluis Renkforce
- Kluis ROMA
- Kluis Rottner
- Kluis Royal Safe
- Kluis Royal Sovereign
- Kluis Salvus
- Kluis Sentry
- Kluis Sistec
- Kluis SMC
- Kluis Sygonix
- Kluis Technomax
- Kluis Thule
- Kluis Toolland
- Kluis Topcraft
- Kluis Tulox
- Kluis Varo
- Kluis Westfalia
- Kluis Workzone
- Kluis Yale
- Kluis Jewel
- Kluis Juwel
- Kluis Olympia
- Kluis Oxloc
- Kluis First Austria
- Kluis Guzzanti
- Kluis Steren
- Kluis Barska
- Kluis Conrad
- Kluis SereneLife
- Kluis Challenge
- Kluis MSW
- Kluis Hard Head
- Kluis Kidde
- Kluis SentrySafe
- Kluis CAWI
- Kluis Kreator
- Kluis Fichero
- Kluis Kreator-Varo
- Kluis Rottner Tresor
- Kluis Olymp
- Kluis Suncast
- Kluis Winholt
- Kluis Homak Security
- Kluis NOFIRE
- Kluis Stamony
Nieuwste handleidingen voor Kluis
15 November 2024
15 November 2024
15 November 2024
13 November 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
1 Oktober 2024
1 Oktober 2024