HK Audio Lucas Nano 302 Handleiding

HK Audio Speaker Lucas Nano 302

Lees hieronder de 📖 handleiding in het Nederlandse voor HK Audio Lucas Nano 302 (52 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/52

LUCAS

NANO 302

MANUAL 1.0b

• English • Français• Deutsch • Italiano • Español

Version 2.5 12/2016

Important Safety Instructions!

Read before connecting!

This product has been built by the manufacturer in accordance with

IEC 60065 and left the factory in safe working order. To maintain

this condition and ensure non-risk operation, the user must

follow the advice and warning comments found in the operating

instructions. If this product shall be used in vehicles, ships or

aircraft or at altitudes exceeding 2000 m above sea level, take care

of the relevant safety regulations which may exceed the IEC 60065

requirements.

WARNING: To prevent the risk of fire and shock hazard, do not

expose this appliance to moisture or rain. Do not open case – no

user serviceable parts inside. Refer service to qualified service

personnel.

This symbol, wherever it appears, alerts you to the presence

of uninsulated dangerous voltage inside the enclosure – voltage that

may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to the presence

of externally accessible hazardous voltage. External wiring connected

to any terminal marked with this symbol must be a “ready made

cable” complying with the manufacturers recommendations, or must

be a wiring installed by instructed persons only.

This symbol, wherever it appears, alerts you to important

operating and maintenance instructions in the accompanying

literature. Read the manual.

This symbol, wherever it appears, tells you: Take care! Hot

surface! To prevent burns you must not touch.

All electrical and electronic products including batteries

should be disposed of separately from the municipal waste stream

via designated collection facilities appointed by the government or

the local authorities.

• Read these instructions.

• Keep these instructions.

• Follow all warnings and instructions marked on the product and

in this manual.

• Do not use this product near water. Do not place the product near

water, baths, wash basins, kitchen sinks, wet areas, swimming

pools or damp rooms.

• Do not place objects containing liquid on the product – vases,

glasses, bottles etc.

• Clean only with dry cloth.

• Do not remove any covers or sections of the housing.

• The set operating voltage of the product must match the local

mains supply voltage. If you are not sure of the type of power

available consult your dealer or local power company.

• Before connecting the device, please ensure that the mains supply

you are using is equipped with adequate protection against short

circuiting and grounding faults when the device is plugged in.

• To reduce the risk of electrical shock, the grounding of this product

must be maintained. Use only the power supply cord provided with

this product, and maintain the function of the center (grounding)

pin of the mains connection at any time. Make sure the mains

outlet used provides a proper protective ground connection.

• Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the

other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obolete outlet.

• Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where

they exit from the device! Power supply cords should always be

handled carefully. Periodically check cords for cuts or sign of

stress, especially at the plug and the point where the cord exits

the device.

• Never use a damaged power cord.

• Unplug this product during lightning storms or when unused for

long periods of time.

• This product can be fully disconnected from mains only by pulling

the mains plug at the unit or the wall socket. The product must be

placed in such a way at any time, that disconnecting from mains

is easily possible.

• Fuses: Replace with IEC127 (5x20mm) type and rated fuse for best

performance only! It is prohibited to use “patched fuses” or to

short the fuse-holder. Replacing any kind of fuses must only be

carried out by qualified service personal.

• Refer all servicing to qualified service personnel. Servicing is

required when the unit has been damaged in any way, such as:

- When the power cord or plug is damaged or frayed.

- If liquid has been spilled or objects have fallen into the product.

- If the product has been exposed to rain or moisture.

- If the product does not operate normally when the operating

instructions are followed.

- If the product has been dropped or the cabinet has been damaged.

• Do not connect external speakers to this product with an

impedance lower than the rated impedance given on the product

or in this manual. Use only cables with sufficient cross section

according to the local safety regulations.

• Keep away from direct sunlight.

• Do not install near heat sources such as radiators, heat registers,

stoves or other devices that produce heat.

• This apparatus is for moderate climates areas use, not suitable for

use in tropical climates countries.

• Do not block any ventilation openings. Install in accordance with

manufacturer’s instructions. This product must not be placed in

a built-in installation such as a rack unless proper ventilation is

provided.

• Always allow a cold device to warm up to ambient temperature,

when being moved into a room. Condensation can form inside it

and damage the product, when being used without warming up.

• Do not place naked flame sources, such as lighted candles on the

product.

• The device must be positioned at least 20 cm/8“ away from walls.

• Use only with the cart, stand, tripod, bracket or table specified by

the manufacturer or sold with the product. When a cart is used,

use caution when moving the cart/product combination to avoid

injury from tip-over.

• Use only accessories recommended by the manufacturer, this

applies for all kind of accessories, for example protective covers,

transport bags, stands, wall or ceiling mounting equipment. In

case of attaching any kind of accessories to the product, always

follow the instructions for use, provided by the manufacturer.

Never use fixing points on the product other than specified by the

manufacturer.

• This appliance is NOT suitable to be used by any person or

persons (including children) with limited physical, sensorical or

mental ability, or by persons with insufficient experience and/or

knowledge to operate such an appliance. Children under 4 years of

age must be kept away from this appliance at all times.

• Never push objects of any kind into this product through cabinet

slots as they may touch dangerous voltage points or short out

parts that could result in risk of fire or electric shock.

• This product is capable of delivering sound pressure levels in

excess of 90 dB, which may cause permanent hearing damage!

Exposure to extremely high noise levels may cause a permanent

hearing loss. Wear hearing protection if continously exposed to

such high levels.

• The manufacturer only guarantees the safety, reliability and

efficiency of this product if:

- Assembly, extension, re-adjustment, modifications or repairs are

carried out by the manufacturer or by persons authorized to do so.

- The electrical installation of the relevant area complies with the

requirements of IEC (ANSI) specifications.

- The unit is used in accordance with the operating instructions.

• This product is optimized for use with music and speech signals.

Using this product with sine wave, square wave or other kind of

measuring signals at higher level may lead to severe damage of

the product.

General Notes on Safety for Loudspeaker

Systems

Mounting systems may only be used for those loudspeaker

systems authorized by the manufacturer and only with the mounting

accessories specified by the manufacturer in the installation

instructions. Read and heed the manufacturer’s installation

instructions. The indicated load-bearing capacity cannot be

guaranteed and the manufacturer will not be liable for damages in

the event of improper installation or the use of unauthorized

mounting accessories.

The system’s load-bearing capacity cannot be guaranteed and

the manufacturer will not be liable for damages in the event that

loudspeakers, mounting accessories, and connecting and attaching

components are modified in any way.

Components affecting safety may only be repaired by the

manufacturer or authorized agents, otherwise the operating permit

will be voided.

Installation may be performed qualified personnel only, and

then only at pick-points with sufficient load-carrying capacity and in

compliance with local building regulations. Use only the mounting

hardware specified by the manufacturer in the installation

instructions (screws, anchors, etc.). Take all the precautions

necessary to ensure bolted connections and other threaded locking

devices will not loosen.

Fixed and portable installations (in this case, speakers and

mounting accessories) must be secured by two independent safeties

to prevent them from falling. Safeties must be able to catch

accessories or parts that are loose or may become loose. Ensure

compliance with the given national regulations when using

connecting, attaching, and rigging devices. Factor potential dynamic

forces (jerk) into the equation when determining the proper size and

load-bearing capacity of safeties.

Be sure to observe speaker stands’ maximum load-bearing

capacity. Note that for reasons of design and construction, most

speaker stands are approved to bear centric loads only; that is, the

speakers’ mass has to be precisely centered and balanced. Ensure

speaker stands are set up stably and securely. Take appropriate

added measures to secure speaker stands, for example when:

- the floor or ground surface does not provide a stable, secure base.

- they are extended to heights that impede stability.

- high wind pressure may be expected.

- there is the risk that they may be knocked over by people.

Special measures may become necessary as precautions against

unsafe audience behavior. Do not set up speaker stands in

evacuation routes and emergency exits. Ensure corridors are wide

enough and put proper barriers and markings in place when setting

speaker stands up in passageways. Mounting and dismounting

are especially hazardous tasks. Use aids suitable for this purpose.

Observe the given national regulations when doing so.

Wear proper protection (in particular, a helmet, gloves, and

safety shoes) and use only suitable means of ascent (ladders,

scaffolds, etc.) during installation. Compliance with this requirement

is the sole responsibility of the company performing the installation.

WARNING!

After installation, inspect the system comprised of the mounting

fixtures and loudspeakers to ensure it is properly secured.

The operator of loudspeaker systems (fixed or portable) must

regularly inspect or task a third party to regularly inspect all system

components in accordance with the given country’s regulations and

have possible defects repaired immediately.

We also strongly recommend maintaining a logbook or the like to

document all inspections.

When installing speakers for longer lasting or permanent outdoor

operation, be sure to take into account the stability and load-

bearing capacity of platforms and surfaces; loads and forces exerted

by wind, snow, and ice; as well as thermal influences. Also be sure

to provide sufficient safety margins for the rigging points used for

flown systems. Observe the given national regulations when doing

so.

• Ask the manufacturer if your product is allowed for outdoor usage !

Professional loudspeaker systems can produce harmful

volume levels. Even prolonged exposure to seemingly harmless levels

(starting at about 95 dBA SPL) can cause permanent hearing

damage! Therefore we recommend that everyone who is exposed to

high volume levels produced by loudspeaker systems wears

professional hearing protection (earplugs or earmuffs).

Manufacturer: Stamer Musikanlagen GmbH, Magdeburger Str. 8,

66606 St. Wendel, Germany

LUCAS NANO 302 1.0b

Welcome to the HK Audio family!

Thank you for choosing a brand-name product made by our company. Rest

assured, we engineered and built it with the greatest care so it will serve

you well for many tomorrows to come.

Even if your experience with sound systems runs deep, some things about

this product are sure to be new to you. This is why we ask that you do not

set this manual aside without reading it ﬁ rst. Be sure to keep it in a safe

place for later reference.

Here’s wishing you the best sound at every occasion!

Your HK Audio team

Warranty

Use the convenient online registration option at www.hkaudio.com.

http://warranty.hkaudio.com

The registration is only valid if the device is registered within 30 days of

the date of purchase.

HK AUDIO

Technischer Service

Postfach 1509

66959 St. Wendel, Germany

Fax: +49 6851 905 100

Strong electromagnetic interference or electrostatic discharge may

prevent the product from functioning normally. If this happens, the

product may be returned to normal operation by powering o and on

again. Should this not result in the product functioning normally again,

please move the product away from the source of disturbance and try

again.

1 General Info

Contents

When you ﬁ rst unpack your LUCAS NANO 302, take a quick inventory to

make sure the package comes complete with all the contents. LUCAS NANO

302 consists of a powered subwoofer and two satellites. A speaker pole

adapter sleeve (M33 to M20), a protective cap for the speaker pole and a

mains cable are also included, which you’ll ﬁ nd in the box holding the power

cord.

The System's Components

The Subwoofer

The subwoofer houses the 8" woofer, the system’s active circuitry and the

Class D power ampliﬁ ers. The speaker outputs for connecting satellites and

the mains socket are located on the rear. That’s where you’ll also ﬁ nd the

transport bay for the satellites and a recessed Auto Sleep button that acti-

vates an automatic power-saving function. The system's current operating

modes are printed on the inside wall of the satellite bay.

Speaker OutEasy-Click Signal contacts L

S-Connect (M33)

On top of the housing, you’ll ﬁ nd an Easy-Click guide rail

with built-in signal-carrying terminals and an M33 pole

mount that is also able to route the signal. The M33 is

designed to take the S-CONNECT POLE LN speaker ex-

tension pole. The included adapter sleeve (M33 to M20)

lets you attach standard M20 speaker poles, but they

don't have a built-in signal bus.

LUCAS NANO 302

• English • Français• Deutsch • Italiano • Español

Speaker pole adapter

sleeve (M33 to M20)

Product specificaties

Merk:	HK Audio
Categorie:	Speaker
Model:	Lucas Nano 302
Soort bediening:	Buttons, Rotary
Kleur van het product:	Zwart
Gewicht:	10300 g
Gemiddeld vermogen:	230 W
Aantal per verpakking:	1 stuk(s)
Speaker plaatsing:	Vloer
Diameter driver subwoofer (imperiaal):	8 "
Peak Music Power Output (PMPO):	750 W
Frequentiebereik:	44 - 20000 Hz
Diameter woofer:	3.5 "
Aantal woofer drivers:	2
Diameter hogetonenluidspreker:	1 "
Aantal tweeter drivers:	2
Geluidsdruk niveau (max):	120 dB
Versterker klasse:	D
Ingebouwde versterker:	Ja