Hitachi C10FCG Handleiding
Hitachi
Zaagmachine
C10FCG
Lees hieronder de 📖 handleiding in het Nederlandse voor Hitachi C10FCG (49 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/49
DOUBLE INSULATION
DOUBLE ISOLATION
AISLAMIENTO DOBLE
Model
Modèle
Modelo
C 10FCG
Compound Miter Saw
Scie à onglets combinée
Sierra ingletadora
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this
manual BEFORE operating the power tool. Please keep this manual available for other users and owners
before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de
sérieuses blessures corporelles !
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière
de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi
à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode
d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar en lesiones
de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este
manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras
personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.
English PAGE PAGE
Français PAGE PAGE
Español PÁGINA PÁGINA
CONTENTS
TABLE DES MATIERES
ÍNDICE
SPÉCIFICATIONS ......................................................21
ACCESSOIRES .......................................................... 21
APPLICATIONS ..........................................................22
PRÉPARATION AVANT L’UTILISATION .....................22
AVANT L’UTILISATION ...............................................23
AVANT LA COUPE ..................................................... 23
APPLICATIONS PRATIQUES .....................................24
INSTALLATION ET RETRAIT DE LA LAME ...............28
ENTRETIEN ET INSPECTION ...................................28
SERVICE APRÈS-VENTE ET RÉPARATIONS ...........29
GUIDE DE DÉPANNAGE ............................................30
LISTE DES PIECES ....................................................46
INFORMATIONS IMPORTANTES DE SÉCURITÉ ..... 17
SIGNIFICATION DES MOTS D’AVERTISSEMENT .... 17
SECURITE ..................................................................... 17
CONSIGNES DE SECURITE RELATIVES AUX
OUTILS ÉLECTRIQUES ...................................... 17
PIECES DE RECHANGE ............................................ 18
UTILISER LE CORDON DE
RALLONGE APPROPRIÉ .................................... 19
DOUBLE ISOLATION POUR UN
FONCTIONNEMENT PLUS SUR......................... 19
UTILISATION ET ENTRETIEN ......................................20
NOM DES PIÈCES .....................................................20
APPLICATIONS ............................................................7
PREPARATION BEFORE OPERATION .......................7
BEFORE USING ...........................................................8
BEFORE CUTTING ......................................................9
PRACTICAL APPLICATIONS .....................................10
SAW BLADE MOUNTING AND
DISMOUNTING ................................................... 13
MAINTENANCE AND INSPECTION ..........................14
SERVICE AND REPAIRS............................................15
TROUBLESHOOTING GUIDE ................................... 16
PARTS LIST ................................................................46
IMPORTANT SAFETY INFORMATION ........................3
MEANINGS OF SIGNAL WORDS ................................3
SAFETY ............................................................................3
IMPORTANT SAFETY INSTRUCTIONS FOR
USING ALL POWER TOOLS .................................3
REPLACEMENT PARTS ..............................................4
USE PROPER EXTENSION CORD .............................4
DOUBLE INSULATION FOR SAFER OPERATION ......5
OPERATION AND MAINTENANCE ................................5
NAME OF PARTS .........................................................5
SPECIFICATIONS ........................................................6
ACCESSORIES ............................................................7
ESPECIFICACIONES .................................................35
ACCESORIOS ............................................................ 35
APLICACIONES..........................................................36
PREPARATIVOS PREVIOS A LA OPERACIÓN .........36
ANTES DE LA UTILIZACIÓN .....................................37
ANTES DEL CORTE ...................................................37
APLICACIONES PRÁCTICAS ....................................38
MONTAJE Y DESMONTAJE DE LA
HOJA DE SIERRA ...............................................42
MANTENIMIENTO E INSPECCIÓN ...........................43
SERVICIO Y REPARACIONES ...................................44
GUIA DE IDENTIFICACION DE PROBLEMAS ...........45
LISTA DE PIEZAS .......................................................46
INFORMACIÓN IMPORTANTE SOBRE
SEGURIDAD ........................................................ 31
SIGNIFICADO DE LAS PALABRAS DE
SEÑALIZACIÓN ...................................................31
SEGURIDAD .................................................................. 31
NORMAS DE SEGURIDAD PARA LAS
HERRAMIENTAS ELÉCTRICAS ..........................31
PIEZAS DE REEMPLAZO .......................................... 32
UTILICE EL CABLE PROLONGADOR
ADECUADO .........................................................33
AISLAMIENTO DOBLE PARA OFRECER UNA
OPERACIÓN MÁS SEGURA ...............................33
OPERACIÓN Y MANTENIMIENTO ...............................34
NOMENCLATURA DE PARTES .................................34
3
English
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power
tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can
often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain the operation and maintenance
instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identifi ed by WARNINGS on the power tool and in this Instruction Manual.
Never use this power tool in a manner that has not been specifi cally recommended by HITACHI.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or may cause machine damage.
NOTE emphasizes essential information.
SAFETY
IMPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS
READ ALL OF THE WARNINGS AND OPERATING INSTRUCTIONS IN THIS MANUAL BEFORE OPERATING OR
MAINTAINING THIS TOOL:
WARNING:
When using this electric tool, take all necessary precautions to minimize the risk of electric shock or other personal injury.
In particular, always comply with the following safety rules:
1. ALWAYS KEEP GUARDS IN PLACE and in working order.
2. ALWAYS REMOVE ADJUSTING KEYS AND WRENCHES BEFORE
STARTING TOOL. Always confi rm that all keys and adjusting wrenches
have been removed from the tool before it is turned on.
3. ALWAYS KEEP WORK AREA CLEAN. Avoid injuries by not cluttering
the work areas and work benches.
4. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS. Never use the
power tool in damp or wet places and never expose it to rain. Always keep
the work area well lighted.
5. NEVER PERMIT CHILDREN OR OTHERS TO LOITER NEAR THE
WORK AREA. Keep all people (especially children) away from the work
area. Always unplug unattended tools and keep the work place tamper-
proof by installing locks on the doors and on the master switches.
6. NEVER FORCE THE TOOL. It will do the job better and more safely if it
is operated at the rate for which it was designed.
7. ALWAYS USE THE RIGHT TOOLS. Never force a tool or an attachment
to do a job for which it was not designed.
8. ALWAYS WEAR PROPER APPAREL WHEN WORKING WITH THE
TOOL. Never wear loose clothing, gloves, neckties, rings, bracelets or
other jewelry which may get caught in the moving parts. Always wear
non-slip footwear, preferably with steel toes. Wear protective hair covering
to contain long hair.
9. ALWAYS WEAR EYE PROTECTION WITH SIDE SHIELDS THAT
MEETS THE REQUIREMENTS OF ANSI STANDARD Z87.1 WHEN
WORKING WITH THE TOOL TO PREVENT EYE INJURY. Ordinary
eyeglasses do not provide adequate protection because they do not
contain impact resistant safety glass. Also, use a face mask for additional
safety and wear a dust mask if the cutting operation produces dust.
10. ALWAYS SECURE THE WORKPIECE TO THE FENCE OR THE TABLE.
Use clamps or a vise to hold the workpiece in place. It is safer than using
your hand and it frees both hands to operate the tool.
11. NEVER OVERREACH. Always keep proper footing and balance when
working with the tool.
12. ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and
clean for the best and safest performance. Always follow instructions for
lubricating the tool and for changing accessories.
13. ALWAYS DISCONNECT THE TOOL before servicing and before
changing blades or other accessories.
14. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN
THE TOOL. Always confi rm that the switch is in the OFF position before
inserting the power plug into the receptacle.
15. ALWAYS USE RECOMMENDED ACCESSORIES ONLY WHEN
OPERATING THIS TOOL. Consult this instruction manual for descriptions
of recommended accessories. To avoid personal injuries, use only
recommended accessories in conjunction with this tool.
16. NEVER STAND ON THE TOOL. Prevent serious injury by not tipping the
tool and by not risking unintentional contact with the saw blade.
17. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL.
Always check the guard and all other components for damage before
using the tool to assure that they will function properly. Check all moving
parts for proper alignment, freedom from binding and other conditions
that might aff ect proper operation. Always repair or replace any damaged
guards or other damaged components before using the tool.
18. ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE
BEFORE USING THE TOOL. Always feed work into the tool against the
rotation direction of the blade in order to prevent possible injury.
19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. TURN
POWER OFF. Do not leave tool until it comes to a complete stop. Always
turn the power off when the tool is not in use. Always unplug the power
cord when the tool is not in use.
20. This tool was not designed to be used for mass-production applications
and should not be used in mass-production environments.
21. When servicing this tool, use only authorized replacement parts.
22. Apply 120 volts AC only to this tool. Applying the wrong voltage or applying
DC power can cause the POWER TOOL to operate improperly and cause
serious personal injury or damage to the tool.
23. Never raise the saw blade from the workpiece until it has fi rst come to a
complete stop.
24. Always use outboard stands to provide support for long workpieces that
overhang the table of the slide compound miter saw.
25. Always return the carriage to the full rear position after each crosscut
operation in order to reduce the risk of injury.
26. POLARIZED PLUGS To reduce the risk of electric shock, this equipment
has a polarized plug (one blade is wider than the other). This plug will fi t
in a polarized outlet only one way. If the plug does not fi t fully in the outlet,
reverse the plug. If it still does not fi t, contact a qualifi ed electrician to
install the proper outlet. Do not change the plug in any way.
Specifi c Safety Rules for Use of this Power Tool
WARNING:
The following specifi c operating instructions must be observed
when using this POWER TOOL in order to avoid injury:
DO’s
ALWAYS OBSERVE THE FOLLOWING RULES TO
ASSURE SAFE USE OF THIS TOOL:
1. Review this Manual and familiarize yourself with the safety rules and
operating instructions for this POWER TOOL before attempting to use it.
2. Remove all packing materials attached or connected to the tool before
attempting to operate it.
3. Always confi rm that the POWER TOOL is clean before using it.
4. Always wear snug-fi tting clothing, non-skid footwear (preferably with steel
toes) and eye protection when operating the POWER TOOL.
Product specificaties
| Merk: | Hitachi |
| Categorie: | Zaagmachine |
| Model: | C10FCG |
Heb je hulp nodig?
Als je hulp nodig hebt met Hitachi C10FCG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Zaagmachine Hitachi
27 Mei 2024
27 Mei 2024
4 Mei 2024
20 Augustus 2023
19 Augustus 2023
18 Augustus 2023
18 Augustus 2023
17 Augustus 2023
17 Augustus 2023
17 Augustus 2023
Handleiding Zaagmachine
- Zaagmachine Bosch
- Zaagmachine AEG
- Zaagmachine DeWalt
- Zaagmachine Ford
- Zaagmachine Al-ko
- Zaagmachine Atika
- Zaagmachine BabyGO
- Zaagmachine Batavia
- Zaagmachine Bavaria
- Zaagmachine Bebe Confort
- Zaagmachine BGU
- Zaagmachine Black Decker
- Zaagmachine Blucave
- Zaagmachine Bort
- Zaagmachine Brennenstuhl
- Zaagmachine Bruder Mannesmann
- Zaagmachine Budget
- Zaagmachine Defort
- Zaagmachine Dolmar
- Zaagmachine Dremel
- Zaagmachine Duro
- Zaagmachine Duro Pro
- Zaagmachine Echo
- Zaagmachine Einhell
- Zaagmachine Elektra Beckum
- Zaagmachine Elu
- Zaagmachine Ergofix
- Zaagmachine Exakt
- Zaagmachine Fein
- Zaagmachine Felisatti
- Zaagmachine Ferm
- Zaagmachine Ferrex
- Zaagmachine Festool
- Zaagmachine Flex
- Zaagmachine Florabest
- Zaagmachine FOM
- Zaagmachine Fuxtec
- Zaagmachine Gamma
- Zaagmachine Gardena
- Zaagmachine Gardenline
- Zaagmachine Germania
- Zaagmachine Global
- Zaagmachine Goon
- Zaagmachine Greenworks
- Zaagmachine Grizzly
- Zaagmachine Gude
- Zaagmachine Gude Pro
- Zaagmachine Hammer
- Zaagmachine Hikoki
- Zaagmachine Holzmann
- Zaagmachine Homelite
- Zaagmachine Husqvarna
- Zaagmachine Huvema
- Zaagmachine Hyundai
- Zaagmachine Ideal
- Zaagmachine Kompernass
- Zaagmachine Kress
- Zaagmachine Lux Tools
- Zaagmachine Luxor
- Zaagmachine Maestro
- Zaagmachine Makita
- Zaagmachine Maktec
- Zaagmachine Matrix
- Zaagmachine Max
- Zaagmachine Maxx
- Zaagmachine McCulloch
- Zaagmachine Metabo
- Zaagmachine Milwaukee
- Zaagmachine Parkside
- Zaagmachine Pattfield
- Zaagmachine Plantiflor
- Zaagmachine Powerfix
- Zaagmachine Powerplus
- Zaagmachine Remington
- Zaagmachine Robust
- Zaagmachine Ryobi
- Zaagmachine Scheppach
- Zaagmachine Shindaiwa
- Zaagmachine Silverline
- Zaagmachine Skil
- Zaagmachine Solo
- Zaagmachine Stanley
- Zaagmachine Sterwins
- Zaagmachine Stiga
- Zaagmachine Stihl
- Zaagmachine Tanaka
- Zaagmachine Texas
- Zaagmachine Toledo
- Zaagmachine Toolcraft
- Zaagmachine Topcraft
- Zaagmachine Triton
- Zaagmachine Trotec
- Zaagmachine Troy-Bilt
- Zaagmachine Varo
- Zaagmachine Vonroc
- Zaagmachine Westfalia
- Zaagmachine Workzone
- Zaagmachine Worx
- Zaagmachine Zipper
- Zaagmachine Oregon Scientific
- Zaagmachine Ozito
- Zaagmachine Black And Decker
- Zaagmachine Cocraft
- Zaagmachine Draper
- Zaagmachine Meec Tools
- Zaagmachine Lionelo
- Zaagmachine Clarke
- Zaagmachine Genesis
- Zaagmachine Hilti
- Zaagmachine Cobra
- Zaagmachine Hobart
- Zaagmachine ACG
- Zaagmachine Cotech
- Zaagmachine Power Craft
- Zaagmachine Tacklife
- Zaagmachine Truper
- Zaagmachine Fieldmann
- Zaagmachine Mafell
- Zaagmachine Prime3
- Zaagmachine Proxxon
- Zaagmachine Biltema
- Zaagmachine Porter-Cable
- Zaagmachine Sun Joe
- Zaagmachine Yard Force
- Zaagmachine Challenge
- Zaagmachine EGO
- Zaagmachine Hurricane
- Zaagmachine MacAllister
- Zaagmachine Maruyama
- Zaagmachine Sovereign
- Zaagmachine Spear & Jackson
- Zaagmachine Royal Catering
- Zaagmachine Dedra
- Zaagmachine Graphite
- Zaagmachine Narex
- Zaagmachine RIDGID
- Zaagmachine Tryton
- Zaagmachine CMI
- Zaagmachine Garland
- Zaagmachine Herkules
- Zaagmachine Powerworks
- Zaagmachine MSW
- Zaagmachine Sthor
- Zaagmachine Evolution
- Zaagmachine Craftsman
- Zaagmachine Rikon
- Zaagmachine Verto
- Zaagmachine Erbauer
- Zaagmachine Snow Joe
- Zaagmachine Chicago Pneumatic
- Zaagmachine Alpha Tools
- Zaagmachine Hazet
- Zaagmachine Yato
- Zaagmachine Jonsered
- Zaagmachine Qualcast
- Zaagmachine Total
- Zaagmachine Avantco
- Zaagmachine Bestgreen
- Zaagmachine Masport
- Zaagmachine Morrison
- Zaagmachine Stalco
- Zaagmachine Baumr-AG
- Zaagmachine Martha Stewart
- Zaagmachine IKRA
- Zaagmachine MTM
- Zaagmachine Meister Craft
- Zaagmachine Łucznik
- Zaagmachine King Craft
- Zaagmachine Max Bahr
- Zaagmachine Toolson
- Zaagmachine Wolfcraft
- Zaagmachine Kreg
- Zaagmachine Vulcan
- Zaagmachine Anova
- Zaagmachine Challenge Xtreme
- Zaagmachine Pro-Cut
- Zaagmachine Power Smart
- Zaagmachine Backyard Pro Butcher Series
- Zaagmachine EFA
- Zaagmachine Einhell Bavaria
- Zaagmachine McKenzie
- Zaagmachine Prowork
- Zaagmachine Proviel
- Zaagmachine Backyard Pro
- Zaagmachine Ultranatura
- Zaagmachine FIXIT
- Zaagmachine Ergotools Pattfield
- Zaagmachine MyTool
- Zaagmachine Bavaria By Einhell
- Zaagmachine Donau Elektronik
- Zaagmachine Rona
- Zaagmachine TAURUS Titanium
- Zaagmachine Maxbear
- Zaagmachine Extralink
- Zaagmachine Yellow Garden Line
- Zaagmachine Turbo-Silent
Nieuwste handleidingen voor Zaagmachine
23 December 2024
20 December 2024
19 December 2024
19 December 2024
17 December 2024
16 December 2024
16 December 2024
16 December 2024
5 December 2024
5 December 2024