Hikvision DS-2CE16D9T-AIRAZH Handleiding

Hikvision Bewakingscamera DS-2CE16D9T-AIRAZH

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-2CE16D9T-AIRAZH (3 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

TURBO HD

Motorized Vari-focal IR

Bullet Camera

User Manual

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FC C

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FC C

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):This

product contains a battery that cannot

be disposed of as unsorted municipal

waste in the European Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

U D.6L0201D2016A01

2012/19/EU (W EEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

This product and - if applicable - the

supplied accessories too are marked

with "CE" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EM C Directive 2004/108/E C,

the RoHS Directive 2011/65/EU.

This series of camera adopts new generation

sensor with high sensitivity and advanced circuit

design technology It features high resolution,.

low image distortion and low noise, etc , which.

makes it suitable for surveillance system and

image processing system.

l HD1080p video output

0.1Lux @ (F1.2,AGC ON), 0 Lux with IR

5-50mm motorized VF lens, auto focusl

lSmart IR Mode

s are configurable

OSD menu, parameter

Auto white balance, auto gain control, WDR Functionl

High performance 2M P CMOS sensor and highl

resolution bring high-quality image

1 Introduction

1.1 Product Features

1.2 Overview

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual applies to DS-2CE16D9T-AIRAZ H

model motorized vari-focal IR bullet camera.

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

0200001050626

Please refer to the product specification for

camera parameters and functions.

Privacy Notice

Surveillance laws vary by jurisdiction. Check

all relevant laws in your jurisdiction before using

this product for surveillance purposes to ensure

that your use of this product conforms.

Industry Canada ICES-003 Compliance

This device meets the CAN IC ES-3 (A)/NM B-3(A)

standards requirements.

1.2.1 Overview of Vari-Focal IR Bullet Camera

Figure 1-1 Overview of Bullet Camera

Device supports 12V DC and 24V AC power supply.

Heater function will only be enabled with 24V AC.

Power Cable

HD Video

Cable

CVBS Cable

Mounting Base

Sun Shield

Motorized Vari-Focal Lens

2 Installation

Before you start:

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

2.1 Ceiling Mounting

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Hammer the supplied plastic expansion bolt into

the screw holes.

Figure 2-1 Drill Template

Steps:

Ceiling Mounting

2 2

1:Screw Hole for

Bracket

2:Screw Hole for

Mounting Base

4-45°

Φ88.7

8-Φ5.0

3.Route the cables to the cable hole and connect

the corresponding cables.

4.Fix the camera to the ceiling with the supplied

PA4 screws.

3 Menu Operation

Figure 3-1 Main Menu

DAY&NIGHTBACKLIGHT

INDOOR

OUTDOOR

ZOOM

SPEED SHUTTER

AGC

SENS-UP

BRIGHTNESS

D-WDR

DEFOG

BLC

HSBLC

ATW

AWC-SET

MANUAL

COLOR

B/W

TRIGGER

2D NR

3D NR

CAM

TITLE

D-EFFECT

MOTION

PRIVACY

DEFECT

HEAT

CTRL

SHARPNESS

MONITOR

LSC

PRESET

FOCUS

MODE

LENSINIT

ZOOM

VIEW

AFLIMIT

WDR

OFF

AUTO

You can call the menu and adjust the camera

parameters with the direction button or a coaxial

camera controller (purchase separately). You can

also call the menu with supported DVR.

3.1 V IDEO.OUT

PAL or NTSC is selectable .

3.2 LANGUAGE

Chinese and English are selectable.

3.3 SETUP

3.3.1 SCENE

You can select indoor and outdoor scene modes

according to the working environments.

3.3.2 LE NS

The camera is equipped with 5-50mm motorized

vari-focal lens.

Click Zoom + and Zoom - on the DVR PTZ to zoom in

and zoom out. The camera automatically focuses

after zooming in/out.

Move the cursor left/right to adjustZOOM SPEED:

the zoom speed.

PRESET: You can set, delete, and call the preset. 1

to 64 presets are configurable.

Figure 2-2 Fix the Camera to the Ceiling

Figure 2-4 3-axis Adjustment

Figure 2-5 Fix the Camera to the Wall

5.Rotate the cover of camera anticlockwise and the

direction button, auxiliary video interface, and

the DIP switch show.

1.Direction Button

2.Auxiliary Video Output

3.DIP Switch

Figure 2-3 Image Adjustment

l A small monitor can be connected to the auxiliary

video output to adjust the video.

DIP switch is used to enable/disable WDR function.

(By disabling WDR function, video output can be

realized by both CVBS output and HD video output.)

(By enabling WDR function, video output cannot be

realized by CVBS output.)

360°

90°

360°

6. Adjust the surveillance angle.

1). Loosen No.1 adjusting screw to adjust the pan

position (0 ~ 360 ).° °

2). Loosen No.2 adjusting screw to adjust the

tilting position(0 ~ 90 ).° °

3). Loosen No.3 adjusting screw to adjust the

rotation position 0 ~ 360 .( ° ° )

4).Tighten the adjusting screws.

2.2 Wall Mounting

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Hammer the supplied plastic expansion bolt into

the screw holes.

3.Route the cables to the cable hole and connect

the corresponding cables.

4.Fix the camera to the ceiling with the supplied

PA4 screws.

5.Adjust the surveillance angle as shown in the

figure 2-4.

3.3.3 EXPOSURE

EXPOSURE

1. EXPOSURE IRIS-PRI

2. SHUTTER AUTO

3. AGC OFF

4. SENS-UP ---

5. BRIGHTNESS ---|------ 40

6. D-WDR OFF

7. DEFOG OFF

8. RETURN RETURN

Figure 3-2 Exposure

EXPOSURE: Manual and I RIS-PRI a re selectable.

SHUTTER: AUTO,1/25, 1/75, 1/100, 1/120…1/3.5k

, 1/6k, 1/10k, 1/20k and 1/30 kare selectable.

: You can set the AGC value from 0 to 15.AGC

: You can set the SE NS-U P to OF F or AUT O.SEN S-UP

: You can set the brightness valueBRIG HTNESS

from 1 to 14.

You can set the D-WD R as ON or OF F.D-W DR:

: You can set the defog function as ON toDEFOG

enable the function. Position, size, and the defog

gradation are configurable.

3.3.4 Backlight

WDR

Set the W DR status as ON or OF F.

Backlight Compensation (BLC):

Set the gain of BLC as High, Middle, or Low.-GA IN:

Press the up/down/left/right button to-AREA:

define the BLC position and size. Select RET or

AG AIN to go back the B LC menu or re-define the

BLC a rea.

Restore the BLC settings to the default.-Default:

HSBLC: Select an HSBLC area. Set the DI SPLAY

status as ON. Press the up/down/left/right button

to define the area position and size. Set the HSBLC

LEVEL from 0 to 100. Select ALL DAY or Night for the

HSBLC mode. Set the BLACK MASK status as ON or

OF F.

HSBLC

1. SELECT AREA 1

2. DISPLAY ON 8

3. LEVEL ---|------ 20

4. MODE ALL DAY

5. BLACK MASK ON

6. DEFAULT 8

7. RETURN RETURN

Figure 3-3 HSBLC

3.3.5 White Balance (W B)

MANUAL, AT W (Auto-tracking White Balance),

AWC →SET are selectable.

3.3.6 Day & Night

Auto, Trigger, Color, and B/W are selectable for

DAY and NIGHT swi tches. You can enable IRF in

trigger mode.

3.3.7 NR

: You can set 2D NR status as O N or OF F.2D N R

: Set the Smart NR status as ON and adjust3D N R

the 3D smart NR sensitivity ranges from 0 to 100.

Set the 3D NR LEV EL ranges from 0 to 100. Set the

2D&3D NR

1. 2DNR OFF

2. 3DNR ON 8

3. RETURN RETURN

3D NR

1. SMART NR OFF

2. LEVEL ------|--8 0

3. START. AGC -|--------10

4. END. AGC -|--------10

5. RETURN RETURN

Figure 3-4 NR

Figure 3-5 3D NR

3.3.8 SPECIAL

Edit the camera title on this section.Camera Title:

D-effect:

Set the freeze function as ON or OFF.-FREEZE:

OF F, MIRROR, V-FLIP, and ROTATE are-MI RRO R:

selectable for mirror.

Define the zoom ratio of certain area-D-ZOOM:

from 2 to 62.

Set the NEG IMAGE as ON or OFF.-N EG.IMA GE:

SPECIAL

1. CAM TITLE OFF

2. D-DFFECT 8

3. MOTION OFF

4. PRIVACY OFF

5. DEFECT 8

6. HEATCTRL 8

7. RETURN RETURN

Figure 3-6 Special

MOTION

1. SELECT AREA 1

2. DISPLAY ON8

3. SENSITIVITY ----|---- 30

4. MOTION VIEW ON

5. DEFAULT 8

6. RETURN RETURN

Figure 3-7 Motion Detection

Motion: Select a MOT ION area. Set the DI SPLAY

status as ON or OF F. Press the up/down/left/right

button to define the position and size of the area.

Set the SEN SI TI VI TY from 0 to 100. Set the

MOTION VIEW status as ON or OF F.

Privacy: Select a PRI VACY area. Set the DISP LAY

status as INV, MOSAI C, COLOR or OF F. Press the

up/down/left/right button to define the position

and size of the area. Up to 8 areas are configurable.

Defect: LI VE DP C and STAT IC DP C are selectable

in this section.

PRIVACY

1. SELECT AREA 1

2. DISPLAY MOSAIC 8

3. COLOR 10

4. TRANS. 1

5. DEFAULT 8

6. RETURN RETURN

ADJUST

1. SHARPNESS --------|15

2. MONITOR LCD8

3. LSC OFF

4. RETURN RETURN

3.3.9 ADJUST

: Adjust the sharpness from 0 to 15.Sharpness

: Monitor CRT, and Monitor LC D areMonitor

selectable.

: Set the LSC status as O N or O FF.LSC

3.3.10 RESET

Reset all the settings to the default.

3.3.11 EXIT

Press OK to exit the menu.

START. AGC level as the threshold to enable AGC ,

and set the END. AG C level as the threshold to

disable AGC.

Figure 3-8 Privacy Mask Figure 3-9 Adjust

FOCUS MODE: Manual, Auto, and Trigger modes

are selectable. In auto mode, the camera focuses

automatically, and in manual mode, you can click

Zoom+ and Zoom- to focus.

You can reset the lens.LENSINIT:

AFLIMIT: 20m, 10m, 6m, 3m, 1.5m, 1m, 30cm, and

10cm are selectable as the Min. focus distance limit.

Enable the zoom view and the zoomZOOM VIEW:

ratio displays while lens zooming in/out.

HEAT CTRL: AUT O, ON and OF F are selectable in

this section.

Product specificaties

Merk:	Hikvision
Categorie:	Bewakingscamera
Model:	DS-2CE16D9T-AIRAZH
Kleur van het product:	Wit
Gewicht:	1650 g
Breedte:	100.8 mm
Diepte:	313.5 mm
Hoogte:	107.3 mm
Soort:	CCTV-bewakingscamera
Internationale veiligheidscode (IP):	IP66
Vormfactor:	Rond
Automatisch scherpstellen:	Ja
Ondersteuning voor plaatsing:	Binnen & buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Plafond/muur
Ondersteunde video-modi:	1080p
Maximum resolutie:	1944 x 1092 Pixels
Totaal aantal megapixels:	2 MP
Stroomuitvoer (volt):	12
Minimale belichting:	0 Lux
Field of view (FOV) hoek:	59.8 °
Aantal cameras:	1
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Zoomcapaciteit:	Ja
Brandpuntbereik:	- mm
Vermogensverbruik (max):	20 W
Formaat analoog signaal:	NTSC,PAL
Volledige HD:	Ja
Type beeldsensor:	CMOS
Digitale zoom:	62 x
Camera sluitertijd:	1/25 - 1/50000 s
Witbalans:	ATW,AWC,Manual
Ondersteunde grafische resoluties:	1920 x 1080 (HD 1080)
Ruisonderdrukking:	Ja
Maximaal 30 frames per seconde:	25 fps
Composiet video-uitgang:	1
Signaal/ruis-verhouding:	62 dB
Ondersteunde talen:	CHI (SIMPL),CHI (TR),ENG
Power over Ethernet (PoE):	Nee
PTZ control:	Ja
Draaihoek:	360 °
Pan bereik:	0 - 360 °
Dag/nacht modus:	Ja
Maximum aperture number:	1.2
Video uit:	1
Bewegingssensor:	Ja
Weerbestendig:	Ja
Nachtkijker afstand:	110 m
Infrarood (IR)-afsluitingsfilter:	Ja
Op afstand bekijken:	Ja
Wide Dynamic Range (WDR):	Ja
Wifi:	Nee
AC-ingangsspanning:	24 V
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Bereik kantelhoek:	0 - 90 °
Privézone maskeren:	Ja
Draaien & spiegelen:	Ja