Hikoki G 18DBBAL Handleiding
Hikoki
Slijpmachine
G 18DBBAL
Lees hieronder de 📖 handleiding in het Nederlandse voor Hikoki G 18DBBAL (17 pagina's) in de categorie Slijpmachine. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/17
G 18DBBAL
Handling instructions
2
c) Prevent unintentional starting. Ensure the
switch is in the off position before connecting to
power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your fi nger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may aff ect the
power tool s operation.ʼ
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations diff erent from
those intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of fi re when used with another
battery pack.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
3
b) Use power tools only with specifi cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
SAFETY WARNINGS COMMON FOR
GRINDING OR ABRASIVE CUTTING-
OFF OPERATIONS
a) This power tool is intended to function as a
grinder or cut-off tool. Read all safety warnings,
instructions, illustrations and specifi cations
provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
b) Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c) Do not use accessories which are not specifi cally
designed and recommended by the tool
manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated speed can
break and fl y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted
by fl anges, the arbour hole of the accessory must
fi t the locating diameter of the fl ange.
Accessories that do not match the mounting hardware of
the power tool will run out of balance, vibrate excessively
and may cause loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
h) Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments.
The eye protection must be capable of stopping fl ying
debris generated by various operations. The dust mask
or respirator must be capable of fi ltrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory may
fl y away and cause injury beyond immediate area of
operation.
j) Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and could give the operator
an electric shock.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and pull
the power tool out of your control.
m) Do not run the power tool while carrying it at your
side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
o) Do not operate the power tool near fl ammable
materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED
WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
Product specificaties
| Merk: | Hikoki |
| Categorie: | Slijpmachine |
| Model: | G 18DBBAL |
Heb je hulp nodig?
Als je hulp nodig hebt met Hikoki G 18DBBAL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Slijpmachine Hikoki
3 Juli 2024
25 November 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
1 Augustus 2023
1 Augustus 2023
1 Augustus 2023
1 Augustus 2023
1 Augustus 2023
Handleiding Slijpmachine
- Slijpmachine Bosch
- Slijpmachine AEG
- Slijpmachine DeWalt
- Slijpmachine ABB
- Slijpmachine Adler
- Slijpmachine Aquapur
- Slijpmachine ATI-ZDL
- Slijpmachine Batavia
- Slijpmachine Bavaria
- Slijpmachine Black Decker
- Slijpmachine Bort
- Slijpmachine Bruder Mannesmann
- Slijpmachine Bunn
- Slijpmachine Defort
- Slijpmachine Dolmar
- Slijpmachine Dolmar(Makita)
- Slijpmachine Dremel
- Slijpmachine Duro
- Slijpmachine Duro Pro
- Slijpmachine Einhell
- Slijpmachine Ergofix
- Slijpmachine Fein
- Slijpmachine Felisatti
- Slijpmachine Ferm
- Slijpmachine Festool
- Slijpmachine Flex
- Slijpmachine Florabest
- Slijpmachine Gamma
- Slijpmachine Global
- Slijpmachine Goon
- Slijpmachine Gorenje
- Slijpmachine Gude
- Slijpmachine Gude Pro
- Slijpmachine Hitachi
- Slijpmachine Holzmann
- Slijpmachine Husqvarna
- Slijpmachine Hyundai
- Slijpmachine Kawasaki
- Slijpmachine Kress
- Slijpmachine Maestro
- Slijpmachine Makita
- Slijpmachine Maktec
- Slijpmachine Max
- Slijpmachine Mesko
- Slijpmachine Metabo
- Slijpmachine Milwaukee
- Slijpmachine Parkside
- Slijpmachine Pattfield
- Slijpmachine Powerfix
- Slijpmachine Powerplus
- Slijpmachine Profitec
- Slijpmachine Ryobi
- Slijpmachine Scheppach
- Slijpmachine Silvercrest
- Slijpmachine Silverline
- Slijpmachine Skil
- Slijpmachine Solo
- Slijpmachine Stanley
- Slijpmachine Stomer
- Slijpmachine Tanaka
- Slijpmachine Toolcraft
- Slijpmachine Toolland
- Slijpmachine Trotec
- Slijpmachine United Office
- Slijpmachine Vonroc
- Slijpmachine Westfalia
- Slijpmachine Workzone
- Slijpmachine Worx
- Slijpmachine Ozito
- Slijpmachine Black And Decker
- Slijpmachine ECG
- Slijpmachine Steren
- Slijpmachine Cocraft
- Slijpmachine Meec Tools
- Slijpmachine Yamato
- Slijpmachine Genesis
- Slijpmachine Eibenstock
- Slijpmachine Hilti
- Slijpmachine Nuova Simonelli
- Slijpmachine Cotech
- Slijpmachine Power Craft
- Slijpmachine Truper
- Slijpmachine Fieldmann
- Slijpmachine Mirka
- Slijpmachine Proxxon
- Slijpmachine Malmbergs
- Slijpmachine Porter-Cable
- Slijpmachine Graphite
- Slijpmachine RIDGID
- Slijpmachine Tryton
- Slijpmachine Sthor
- Slijpmachine Craftsman
- Slijpmachine Rikon
- Slijpmachine Chicago Pneumatic
- Slijpmachine Alpha Tools
- Slijpmachine Hazet
- Slijpmachine Yato
- Slijpmachine Baumr-AG
- Slijpmachine Meister Craft
- Slijpmachine Neo
- Slijpmachine Victoria Arduino
- Slijpmachine SW-Stahl
- Slijpmachine Cleco
- Slijpmachine Einhell Bavaria
- Slijpmachine McKenzie
- Slijpmachine Proviel
- Slijpmachine Gladiator
- Slijpmachine Rodcraft
- Slijpmachine Bavaria By Einhell
- Slijpmachine Classic Power
- Slijpmachine Handwerk
Nieuwste handleidingen voor Slijpmachine
10 December 2024
5 December 2024
4 December 2024
4 December 2024
23 November 2024
22 November 2024
19 November 2024
19 November 2024
19 November 2024
19 November 2024