Halifax FTHP1030 Handleiding

Halifax Afzuigkap FTHP1030

Lees hieronder de 📖 handleiding in het Nederlandse voor Halifax FTHP1030 (4 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Revised 10/2019

Receiving and Storage

Once equipment is received, check for both obvious and hidden damage. If damage is found, record all

necessary informaon on the bill of lading and le a claim with the nal carrier. Check to be sure that

all parts of the shipment, including accessories, are accounted for.

UNPACKING

Verify that all required parts and the correct quanty of each item have been received. If any items are

missing, report shortages to your representave to obtaining missing parts. Somemes it is not possi-

ble that all items for the unit be shipped together due to availability of transportaon and truck space.

Conrmaon of shipment(s) must be limited to only items on the bill of lading. Filters are typically

shipped in the hood, but somemes are shipped on a separate skid in their original packaging. Do not

remove factory packaging or install lters unl just prior to commissioning. Remove all other shipping/

packing materials.

WARNING!!

Installaon of this unit should only be performed by a qualied professional.

Please read the instrucons thoroughly before installing or servicing this equipment.

LISTING

This hood is listed to ANSI UL710 and CAN/ULC S646-10 and built to the “NFPA 96” Naonal Fire

Protecon Associaon Standard

WARRANTY

This equipment is warranted to be free from defects in materials and workmanship, under normal use

and service, for a period of 24 months from date of shipment – See full Installaon Instrucons for

Details.

INSTALLATION

It is necessary to install and operate this unit with the airow (CFM) designed for the size of hood,

lters and installaon based on the informaon provided.

SITE PREPERATION

1. To safely li equipment into the nal installed posion you must make sure the area of installaon

is clear. Make sure you have enough room aer installaon to service unit easily.

2. Verify the locaon that the hood will be installed so there is

nothing to interfere when installing

the unit.

3. Review your plans and specicaons for your project.

4. Conrm and verify the supports will support the weight of the

hood and fan mounted on top of the truck.

5. If installing light xtures

a. Have electrician following wiring diagram as noted in full

Installaon Manual

6. Weld Duct connecon on top of Hood at area which does not

interfere with bracing inside truck

7. Cut hole in Hood at duct connecon – See Figure #1, Item #7

8. To cut the hole properly in the roof of truck – See Figure #1

a. Li hood in the locaon where it will be mounted, ensuring

there is adequate room available to install the hood and all

ductwork to comply with proper clearances from combusble

material (Item # 1)

b. Bring duct in contact with top of truck (Item # 5)

c. Mark locaon of duct on truck roof

d. Lower hood back down

e. Cut hole in roof of truck (Item # 7)

9. Mount Roof Curb with Curb plate on top of truck

(Items # 3 & 4)

10. See aached instrucons for using Concession Hood Bolt Kit to

complete hood aachment

11. Curb Plate securing

a. Cut Curb Plate hole where duct meets plate to ensure ght t

b. Secure Curb Plate to top of Roof Curb

12. Install and secure fan on top of Roof Curb (Item # 2)

13. Wire power to Fan

14. Use Sealant around roof curb and any holes which were made during the installaon process

IMC, NFPA96 and local authories having jurisdicon may call for a minimum clearance (typically

18 inches for type 1, grease rated hoods) between the cooking hood(s), exhaust ducts, and building

materials which are combusble. However, IMC and NFPA96 do outline acceptable clearance

reducon methods; most local jurisdicng authories will accept the clearance reducon methods

approved in the manufacturer’s UL lisng for Type 1, grease rated hoods.

Product specificaties

Merk:	Halifax
Categorie:	Afzuigkap
Model:	FTHP1030

Heb je hulp nodig?

Als je hulp nodig hebt met Halifax FTHP1030 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Afzuigkap Halifax

Halifax LBSHP1023 Handleiding

9 Juli 2023

Halifax LEXHP1848 Handleiding

5 Juli 2023

Halifax LBSHP1223 Handleiding

5 Juli 2023

Halifax HRHP648 Handleiding

2 Juli 2023

Halifax FTHI740 Handleiding

29 Juni 2023

Halifax HRHP1048 Handleiding

26 Juni 2023

Halifax SCHP1048 Handleiding

25 Juni 2023

Halifax LSCHP648 Handleiding

25 Juni 2023

Halifax FTHI840 Handleiding

22 Juni 2023

Halifax FTHP830 Handleiding

22 Juni 2023

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap

Miele DA 6520 D Handleiding

21 November 2024

Miele DA 420-4 Handleiding

21 November 2024

Miele DA 2906 EXT Handleiding

21 November 2024

Miele DA 2660 Handleiding

21 November 2024

XO R230W Handleiding

21 November 2024

Ilve AGK90 Handleiding

20 November 2024

Ilve AGQ90 Handleiding

20 November 2024

Ilve AGQ60 Handleiding

20 November 2024

Ilve AGQ120 Handleiding

20 November 2024

Ilve AGK120 Handleiding

20 November 2024