Haier HSU-18VNR18 Handleiding

Haier Airco HSU-18VNR18

Lees hieronder de 📖 handleiding in het Nederlandse voor Haier HSU-18VNR18 (8 pagina's) in de categorie Airco. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
0010595326
Contents
1
2
5
7
6
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
TROUBLE SHOOTING
HSU-10VNJ17
HSU-13VNJ17
HSU-20VNJ17
HSU-24NSV13(DC)-SC
HSU-13VNX18
HSU-20VNX18
HSU-25VNX18
HSU-09NFV13(DC)
HSU-12NFV13(DC)
HSU-18NFV13(DC)
HSU-24NFV13(DC)
HSU-09NSV13(DC)-SC
HSU-12NSV13(DC)-SC
HSU-10VNX18
HSU-18NSV13(DC)-SC
HSU-12DW3(DCINV)
HSU-19DW3(DCINV)
HSU-12FW5(DCINV)
HSU-19FW5(DCINV)
HSU-12FS3(DCINV)
HSU-19FS3(DCINV)
HSU-12FW3(DCINV)
HSU-19FW3(DCINV)
HSU-12NMW3A(DCINV)
HSU-18NMW3A(DCINV)
HSU-12NSS3A(DCINV)
HSU-18NSS3A(DCINV)
HSU-12NZS3A(DCINV)
HSU-18NZS3A(DCINV)
HSU-12NRG3A(DCINV)
HSU-18NRG3A(DCINV)
HSU-12NRS3A(DCINV)
HSU-18NRS3A(DCINV)
HSU-24TFW3(DCINV)
HSU-09VNR18
HSU-12VNR18
HSU-18VNR18
HSU-24VNR18 HSU-10VNR19
HSU-13VNR19
HSU-18VNR19
HSU-10VNX19
HSU-13VNX19
HSU-18VNX19
HSU-24VNX19
Parts and Functions
Remote controller
Indoor Unit
Outdoor Unit
4
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
DRAIN HOSE
4
Display board
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
(adjust left and
ow)
Vertical blade
right air fl
Air Purifying Filter
Inlet
(inside)
Emergency
Switch
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Outlet
Inlet grille
6
4
2
1
5
3
(inside)
7
8
Anion generator
Display board 1
4
2
3
1
5
Operation mode indicator
(lights up when the compressor is on.)
Timer mode indicator
(Lights up whenTimer operation is selected.)
Power indicator
(Lights up when unit starts.)
Ambient temp display
When receiving the remote control signal, display the set temperature.
Remote signal receiver
(A beeping sound is generated when a signal from remote controller isreceived.)
2 3 4 5
1
Display board
2
3
Signal receiver
1
Setting temp.display
2
3
Operation mode indicator
1
Display board
Signal receiver hole
COOL display
HEALTH display
4
2
3
1
5
DRY display
6
Ambient temp.display
When receiving the remote
control signal, display the set
temperature.
2
35
64
HEAT display
1
10.
12. SWING LEFT/RIGHT button
13.
15. SLEEP button
14. HEALTH button
16.
18. POWER ON/OFF button
20. TEMP button
21.
TIME OFF/ON 22.1. Mode display
1
2
3
4
5
9
10
11
12
13
14
15
16
17
8
22
23
24
25
19
20
21
18
7
6
HEALTH SLEEP
TIME
OFF
TIME
ON
/QUIET
SWING
Operation mode FANCOOL DRY
Remote controller
2. Signal sending display
4. FAN SPEED display
5. LOCK display
6. TIMER OFF display
TIMER ON display
7. TEMP display
3. SWING display
LO MED HI AUTO
Display
circulated
8.Additional functions display
Operation mode
Remote controller
QUIET TURBOSLEEP HEALTH
9. TURBO/QUIET button
SELF CLEAN button
11. COOL button
FAN SPEED button
LOCK button
Control the lightening and extinguishing
of the indoor LED display board.
17. LIGHT button
19. DRY button
button
SWING UP/DOWN button
23. EXTRA FUNCTION button
24. CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions.
25. RESET button
When the remote controller appears
abnormal, use a sharp pointed
article to press this button to reset
the remote.
Healthy function is not available for some units.
Loading of the battery
1
2
3
4
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with the" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
type fluorescent lamp or
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up.Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
TURBO
SELF
CLEAN
EXTRA
FUNCTION
Function: FAN --- Healthy airflow
position1--- Healthy airflow position 2
(Manual adjustment of some units)
Operation
Air Flow Direction Adjustment
Base Operation
Remote controller
Emergency operation and test operation
Emergency Operation:
Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:
It is impossible to change the settings of temp. and fan speed,It
is also not possible to operate in timer or dry mode.
Pi
1
TURBO/QUIET
HEALTH SLEEP
TIMER
OFF
TIMER
ON
SWING
1
2
2
Press FAN button. For each press, fan speed
follows:
Remote controller:
Press button
Every time the button is pressed, temp.setting
increase 1oC,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1oC,if kept depressed, it will
decrease rapidly
Select a desired temperature.
4.Fan speed selection
3.Select temp.setting
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
1. Unit start
/
2. Select operation mode
COOL button:Cooling mode
DRY button: Dehumidify mode
Display
circulated
changes as
LOW MED HI AUTO
Remote
Controller Note
In DRY mode , when room temperature becomes lower
than temp.setting+2oC, unit will run intermittently at LOW
speed regardless of FAN setting.
In FAN operation mode , the unit will not operate in COOL or
HEAT mode but only in FAN mode, AUTO is not available in
FAN mode. And temp. setting is disabled. In FAN mode,
sleep operation is not available.
Operation
Mode
DRY
COOL
FAN
3
3
4
temperature.according to room
temperature is below 16oC, do not use it in the
Test operation:
Use this switch in the test operation when the room
normal operation.
your finger from the switch: the cooling
Continue to press the test operation
switch for more than 5 seconds . After
you hear the "Pi" sound twice, release
Test operation switch is the same as emergency switch.
operation starts with the air flow speed "Hi".
Under this operation mode,the fan motor of indoor
unit will run in high speed.
Pi Pi
Room
temperature Designated
temperature
Timer
mode Fan
speed
Operation
mode
Above 23 oC 26oC AUTO COOL
No
When restart after remote turning off, the remote controller
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY mode ,
otherwise, condensate water might occur.
at air outlet if all vertical louvers are adjusted to left or right.
will automatically memorize the previous set swing position.
Note:
Vertical flap
Pos.1
(Auto swing)
1.Status display of air flow
2.Left and right air flow adjustment
Pos.1 Pos.2 Pos.3 Pos.4
Pos.5 Pos.6
For each press of button, remote controller
displays as follows :
remote controller:
Cautions:
Initial state
Pos.2 No initial state disaplayed on remote controller, the
vertical flap will be fixed on the current position
2
EXTRA
FUNCTION
SELF
CLEAN
Press button to enter additional options, when
enter to FAN function.
(This function is unavailable on some models.)
Press ON/OFF
on the remote controller,
unit starts.
Note: In some model: The remote has the button ,But the
AC doesn’t have the left and right air flow auto adjustment function.
in this condition, change the direction of vertical blades manually.

Product specificaties

Merk: Haier
Categorie: Airco
Model: HSU-18VNR18

Heb je hulp nodig?

Als je hulp nodig hebt met Haier HSU-18VNR18 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Airco Haier

Haier

Haier KFR-35GW/11WEA22AU1 Handleiding

10 December 2024
Haier

Haier KFR-32GW/11WEA22AU1 Handleiding

10 December 2024
Haier

Haier KFR-35GW/05KBP22A(DS) Handleiding

10 December 2024
Haier

Haier JA-18T Handleiding

9 December 2024
Haier

Haier JA-SP25E Handleiding

9 December 2024
Haier

Haier JA-SP25G Handleiding

9 December 2024
Haier

Haier JA-18L Handleiding

9 December 2024
Haier

Haier JA-16M Handleiding

9 December 2024
Haier

Haier JA-18U Handleiding

9 December 2024
Haier

Haier JA-SP25V Handleiding

9 December 2024

Handleiding Airco

Nieuwste handleidingen voor Airco

Meireles

Meireles MAC 12 W Handleiding

22 December 2024
Meireles

Meireles MAC 18 W Handleiding

22 December 2024
LG

LG PM12EP Handleiding

21 December 2024
Svan

Svan SAAS1200W Handleiding

20 December 2024
Argoclima

Argoclima LOKI PLUS WF Handleiding

18 December 2024
Universal Blue

Universal Blue Grandvalira II 1750 Handleiding

18 December 2024
Universal Blue

Universal Blue Grandvalira II 3000 Handleiding

18 December 2024
Mitsubishi

Mitsubishi WRK20MB2 Handleiding

14 December 2024
Mitsubishi

Mitsubishi SKM25ZSP-W Handleiding

14 December 2024
Mitsubishi

Mitsubishi MSZ-GV2217 Handleiding

14 December 2024