Haier HSU-13VQA22 Handleiding

Haier Airco HSU-13VQA22

Lees hieronder de đź“– handleiding in het Nederlandse voor Haier HSU-13VQA22 (4 pagina's) in de categorie Airco. Deze handleiding was nuttig voor 108 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
WARNING:
Use a cable of suitable length,Do not use tapped wires or an extension lead as this may cause
overheating, electric shocks, fire or explosion.
All the cables shall have got the local authentication certificate. During installation, when the
connecting cables break off, it must be assured that the grouding wire is the last one to be broken off.
If refrigerant gas leaks during installation, ventilate the area immediately.oxic gas may be produced
After completing installation, check for refrigerant gas leakage
When installing or relocating the air conditioner, be sure to bleed the refrigerant circuit to ensure
it is free of air, and use only the specified refrigerant (R32).
Make sure ground connection is correct and reliable.Do not earth the unit to a utility pipe, lightning
conductor or telephone earth lead. Imperfect earthing may result in electric shocks.
Be sure to install an earth leakage circuit explosion-proof breaker.
Do not use means to accelerate the defrosting process or to clean, other than those recommended by
the manufacturer.
The breaker of the air conditioner should be all-pole switch and explosion-proof. The distance
between its two contacts should not be no less than 3mm. Such means for disconnection must be
incorporated in the wiring.
Read the precautions in this manual
carefully before operating the unit. This appliance is filled with R32.
Ask your dealer or qualified personnel to carry out installation work.Do not attempt to install
the air conditioner yourself. Improper Installation may result in water leakage, electric shocks,
fire or explosion.
Keep this manual where the user can easily find it.
Install the air conditioner in accordance with the instructions in this installation manual
Be sure to use only the specified accessories and parts for installation work.
Install the air conditioner on a foundation strong enough to withstand the weight of the unit.
Electrical work must be performed in accordance with relevant local and national regulations
and with instructions in this installation manual,Be sure to use a dedicated power supply circuit
only. The wiring method should be in line with the local wiring standard.The type of connecting
wire is H07RN-F.
.
The appliance must be stored in a room without continuously operating ignition sources, the radius of
the storage area should be no less than 2.5 m (for example:open flames, an operating gas appliance
or an operating electric heater).
Do not pierce or burn.
Be aware that refrigerants may not contain an odour.
Comply with national gas regulations.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.
Cleaning and user maintenance shall not be made by children.
The air conditioner can not be discarded or scrapped Randomly
Reusable mechanical connectors and flared joints are not allowed indoor.
If you need please contact
customer service personnel of Haier to scrap in order to obtain the correct disposal methods.
if the refrigerant comes into contact with fire,and explosion may be happen.
The appliance must be installed, operated and stored in a room with a floor area larger than 3m
The room should be well ventilated.
1
Read technical manual Operator’ manual operating instructions；
0011501394
Drawing for the installation of indoor and outdoor units
Optional parts for piping
Non-adhesive tape
Adhesive tape
Saddle (L.S) with screws
Connecting electric cable
for indoor and outdoor
Drain hose
Heating insulating material
Piping hole cover
The marks from to
in the gure are the
parts numbers.
The distance between
the indoor unit and the
oor should be more
than 2m.
A
G
Necessary Tools for Installation
Driver Torque wrench
(17mm,22mm,26mm)
Nipper
Reamer
Hacksaw Pipe cutter
Gas leakage detector or
soap-and-water solution
Hole core drill Flaring tool
Spanner(17,19 and 26mm) Knife
Measuring tape
Indoor Unit
Place, robust not causing vibration, where the body can be supported suf ciently.
Place, not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
Place, possible to drain easily, where piping can be connected with the outdoor unit.
Place, where cold air can be spread in a room entirely.
Place, nearby a power receptacle, with enough space around. (Refer to drawings).
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and uorescent lamps can be left.
In the case of xing the remote controller on a wall, place where the indoor unit can
receive signals when the uorescent lamps in the room are lightened.
Outdoor Unit
Place, which is less affected by rain or direct sunlight and is suf ciently ventilated.
Place, possible to bear the unit, where vibration and noise are not increased.
Place, where discharged wind and noise do not cause a nuisance to the neighbors.
Place, where a distance marked is available as illustrated in the above gure.
Before inserting power plug into receptacle, check the voltage without fail.
The power source is the same as the corresponding name plate.
Install an exclusive branch circuit of the power.
A receptacle shall be set up in a distance where the power cable can be
reached.Do not extend the cable by cutting it.
Selection of Installation Place
Power Source
A
F
C
E
D
G
B
Arrangement of piping
directions
Rear left
Left Rear
right
Right
Below
Preparation
Please be subject to the actual product purchased ,
the above picture is just for your reference.
Read this manual before installation
Explain suf ciently the operating means to the user according to this manual
Installation Manual of Room Air Conditioner
No. Accessory parts
Remote controller
R-03 dry battery
Mounting plate
11
2
3
4
5
2
1
5
Number
of
articles
Accessory parts
Note:
Accessory parts may vary from each model,
pls refer to the actual parts.
2
Check Items for Test Run
Put check mark in boxes
Gas leak from pipe connecting?
Heat insulation of pipe connecting?
Are the connecting wirings of indoor and outdoor rmly
Is the connecting wiring of indoor and outdoor rmly xed?
Is drainage securely carried out?
Is the earth line securely connected?
Is the indoor unit securely xed?
Is power source voltage abided by the code?
Is there any noise?
Is the lamp normally lighting?
Are cooling and heating (when in heat pump) performed normally?
Is the operation of room temperature regulator normal?
Please kindly explain to our customers how to operate
through the instruction manual.
Check for Installation and Test Run
inserted to the terminal block?
2
Screw Plastic cap
4X25
Screw
4X12
F
A
C
more than
20cm
more than
20cm
more than 10cm
more than30cm
more than 60cm
G
B
PUTTY
POWER USED
Attention must
be paid to the
rising up of
drain hose
more than 30cm
more than 60cm
The models adopt HFC free refrigerant R32
H SU - 1 0 VTH 2 1 (0 3 ) / VTK2 1 HSU-19VTK21
HSU-19VTH21
H SU - 1 3 VTH 2 1 (0 3 ) / VTK2 1
HSU-09LPA03
HSU-10LPA03
HSU-13/19LPB21
HSU-13/19LPC21
HSU-13/19LPA21
HSU-10LPA21
HSU-10LPB21
HSU-10LPC 21
new-1P new-1.5P
440 203
148
HSU-10VXA21 HSU-13VQA22
HSU-13VQC22HSU-13VXA21
HSU-10XSV32
HSU-13XSV32
HSU-12TURBOCOOL(PA)
HSU-18TURBOAQUA
HSU-18UVCOOL(SMART)(INV)(PB)
HSU-18CAE(INV)
Drawing of pipe
A
B
C D
E
60
E
60
â‘ 
②③ ④
Inverter
Models
HSU-18UVC OOL( SMART )(INV)(P
2(L) 3(C)
2(L) 3(C)1(N)
2(L) 3(C)1(N)
1(N)
2(L) 3(C)1(N)
B )
HSU-12CLEANCOOL( INV)(TC)
HSU-12CAE(INV)
HSU-12ANTIRUST COOL( INV)(TH)
HSU-12ENERGYCOOL( INV)(TR)
HSU-18CLEANCOOL( INV)(TC)
HSU-18ANTIRUST COOL(INV)(TH)
HSU-18ENER GY COOL( INV)(TR)
HSU-18CAE(INV)
â‘ 
â‘ 
â‘ 
â‘ 
â‘ 
â‘ 
â‘ 
â‘ 
â‘ 
HSU-24CLEANCOOL( INV)(TC)
HSU-24ANTIRUST COOL( INV)(TH)
HSU-24ENER GY COOL( INV)(TR)
HSU-24CAE(INV)
HSU-24TURBOCOOL(PA )
â‘ 
â‘ 
â‘ 
â‘ 
â‘ 
â‘ 
elbac rewoP
3G1.5
3G2.5
Connect
wi re
4G1.5 4G2.5
HSU-18AQUACOOL(PC)
HSU-18TURBOAQUA
HSU-12TURBOCOOL(PA)
HSU-18TURBOCOOL(PA)
③
③
③
③
③
③
Power cable 3G1.5
3G2.5
Connect w ire 3G1.5 3G2.5
Non-Inverter
Models
Terminal
Models
Terminal
Models
Terminal
Models
Terminal
Models
Non-Inverter
③
③
Power cable 3G1.0 Terminal
Models
3G2.5 Terminal
Models
Connect wire
3G1.0 4G2.5
Models
HSU-25LPA21
HSU-10VTH21/VTK21
HSU-19VTH21/VTK21
HSU-25VTH21
HSU-25VQA22/VQB22/VQC22
HSU-10LPA21
HSU-13/19LPA21
HSU-13/19LPB21
HSU-13 LPA21-1
HSU-13 LPB21-1
HSU-10LPB21
HSU-10VQA22 /VQB22/VQC22
HSU-13VQA22/VQB22/VQC22
HSU-13VTH21/VTK21
③
③
â‘ 
â‘ 
â‘ 
â‘ 
â‘ 
②
②
-mod10/12
P(Q):A-502mm,B-261mm,C-184mm,D-113mm,E-43.4mm
(
HSU-12TURBOCOOL(PA)
)
-mod18
P(Q):A-550mm,B-281mm,C-195mm,D-128mm,E-41mm
( HSU-18AQUACOOL(PC)/HSU-18UVCOOL(SMART)(INV)(PB)/
HSU-18TURBOCOOL(PA))
-mod22-25
P: A-644mm,B-285mm,C-175mm,D-166mm,E-41mm
(
HSU-24TURBOCOOL(PA)
)
-mod10/13 X
:A-502mm,B-261mm,C-170mm,D-110mm,E-52mm
-mod12/15
T:A-500mm,B-261mm,C-175mm,D-107mm,E-42mm
(
HSU-12CLEANCOOL(INV)(TC)/HSU-12ANTIRUSTCOOL(INV)(TH)
/HSU-12ENERGYCOOL(INV)(TR) )
-mod18
T:A-548mm,B-283mm,C-170mm,D-126mm,E-55mm
( HSU-18CLEANCOOL(INV)(TC)/HSU-18ANTIRUSTCOOL(INV)(TH)
/HSU-18ENERGYCOOL(INV)(TR))
-mod22-24
T:A-644mm,B-285mm,C-175mm,D-166mm,E-41mm
( HSU-24CLEANCOOL(INV)(TC)/HSU-24ANTIRUSTCOOL(INV)(TH)
/HSU-24ENERGYCOOL(INV)(TR))
HSU-12CAE(INV)
0.6P
HSU-13LPA21-1
HSU-13LPB21-1
HSU-13LPC21-1
HSU-13VXA21
Inverter â‘ 
â‘ 
â‘ 
Power cable 3G1.0 Terminal
Models
Terminal
Models
Connect wire G1.0
Models
HSU-10VXA21
â‘ 
â‘ 
HSU-10VQA22/VQB22/VQC22
HSU-13VQA22/VQB22/VQC22
HSU-19VQA22/VQB22/VQC22
HSU-19VQA22/VQB22/VQC22
HSU-09CPRA03 T
HSU- 12CP RA03T HSU- 18CP RA03T
HSU- 18CPR A03T
HSU- 09CPR A03T
HSU -12C PRA03T
HSU-18TurboCool(PA)
HSU-12TurboCool(NM)
HSU-24TurboCool(PA)
③
③
②
HSU-18TurboCool(PA)
HSU-24TurboCool(PA)
:A-500mm,B-251mm,C-195mm,D-98mm,E-35mm
35
HSU-18K(FIX)
HSU-12K(FIX)
500138 138
286
HSU-25VTH21
HSU-25LPA21
HSU-25VQA22
HSU-25VQC22
369
new-2P12
HSU-24TURBOCOOL(PA)
HSU-25VQA22/VQB22/VQC22
HSU-24K(FIX)
590 115
115
new-40
329
HSU-24CAE(INV)
490 165
165
new-2P20
329
HSU-25VQA22
HSU-25VQC22
6/6.35mm(1/4 )
9/9.52mm(3/8 ) 12/12.7mm(1/2 )
6/6.35mm(1/4 )
-mod09
P:A- 424.2mm,B-230mm,C-130mm,D-110mm,E-50mm
-mod12P
(
HSU-12TurboCool(NM)
)

Product specificaties

Merk: Haier
Categorie: Airco
Model: HSU-13VQA22

Heb je hulp nodig?

Als je hulp nodig hebt met Haier HSU-13VQA22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Airco Haier

Haier

Haier KFR-35GW/11WEA22AU1 Handleiding

10 December 2024
Haier

Haier KFR-32GW/11WEA22AU1 Handleiding

10 December 2024
Haier

Haier KFR-35GW/05KBP22A(DS) Handleiding

10 December 2024
Haier

Haier JA-18T Handleiding

9 December 2024
Haier

Haier JA-SP25E Handleiding

9 December 2024
Haier

Haier JA-SP25G Handleiding

9 December 2024
Haier

Haier JA-18L Handleiding

9 December 2024
Haier

Haier JA-16M Handleiding

9 December 2024
Haier

Haier JA-18U Handleiding

9 December 2024
Haier

Haier JA-SP25V Handleiding

9 December 2024

Handleiding Airco

Nieuwste handleidingen voor Airco

Meireles

Meireles MAC 12 W Handleiding

22 December 2024
Meireles

Meireles MAC 18 W Handleiding

22 December 2024
LG

LG PM12EP Handleiding

21 December 2024
Svan

Svan SAAS1200W Handleiding

20 December 2024
Argoclima

Argoclima LOKI PLUS WF Handleiding

18 December 2024
Universal Blue

Universal Blue Grandvalira II 1750 Handleiding

18 December 2024
Universal Blue

Universal Blue Grandvalira II 3000 Handleiding

18 December 2024
Mitsubishi

Mitsubishi WRK20MB2 Handleiding

14 December 2024
Mitsubishi

Mitsubishi SKM25ZSP-W Handleiding

14 December 2024
Mitsubishi

Mitsubishi MSZ-GV2217 Handleiding

14 December 2024