Haier HSU-09LEK13/R2(DB) Handleiding

Haier Airco HSU-09LEK13/R2(DB)

Lees hieronder de 📖 handleiding in het Nederlandse voor Haier HSU-09LEK13/R2(DB) (8 pagina's) in de categorie Airco. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Please read this operation manual before using the air conditioner.
Æ”
Keep this operation manual for future reference.
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
0010562830
Contents
1
2
5
7
6
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
TROUBLE SHOOTING
HSU-09LEK13/R2(DB)
HSU-12LEK13/R2(DB)
HSU-18LEK13/R2(DB)
HSU-24LEK13/R2(DB)
HSU-09LEK03/R2(DB)
HSU-12LEK03/R2(DB)
HSU-12CKAS(R2DB)
HSU-18CKAS(R2DB)
HSU-12HKAG(R2DB)
HSU-18HKAG(R2DB)
1
Parts and Functions
Remote controller
Indoor Unit
Outdoor Unit
4
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
DRAIN HOSE
4
Display board
(adjust left and
ow)
Vertical blade
right air fl
Air Purifying FilterInlet (inside)
Emergency
Switch
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Outlet
Inlet grille
Display board 14
235
Signal receiver hole
ON/OFF display
4
2
3
1
5
TIMER ON\OFF display
SLEEP display
Ambient temp.display
When receiving the remote
control signal, display the set
displayed.
time the room temperature is
temperature and in the rest
Note to the power failure resume:
press the sleep button ten times in five seconds
and enter function after hearing four sounds.And
press the sleep button ten times within five
seconds and leave this function after hearing
TIMER ON-OFF display
COOL\HEAT\Dry\AUTO display
two sounds.
1. Mode display
2. Signal sending display
4. FAN SPEED display
5. LOCK display
6. TIMER OFF display
TIMER ON display
LO MED HI
7.TEMP display
16. LOCK button
Used to lock buttons and LCD display.
25. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
22. HOUR button
Operation mode AUTO FANCOOL DRY
Remote controller
1
2
3
4
5
9
10
11
12
13
14
15
16
17
22
23
24
25
19
20
21
8
18
7
6
Control the lightening and extinguishing
of the indoor LED display board.
3. SWING display
8.
9. TURBO button
10. FAN button
11. COOL button
12. AUTO button
13. FAN SPEED button
14. TIMER button
15. SLEEP button
17. LIGHT button
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button
23. EXTRA FUNCTION button
24.CANCEL/CONFIRM button
AUTO
Function: Setting and cancel to the
timer and other additional functions.
Display
circulated
Operation mode
Remote controller
QUIET TURBOSLEEP HEALTH
Additional functions display
NOTE: Healthy function is not available for some units.
Function: Health--- Healthy airflow
position1--- Healthy airflow position 2
--- Restore the original flap position---
Right & left air airflow--- A-B yard---
Refresh air(reserved function)--- QUIET
--- Fahrenheit/Celsius mode conversion
Remote controller A
1. Mode display
2. Signal sending display
4. FAN SPEED display
5. LOCK display
6. TIMER OFF display
TIMER ON display
LO MED HI
7.TEMP display
16. LOCK button
Used to lock buttons and LCD display.
25. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
22. HOUR button
Operation mode AUTO FANCOOL DRY
Remote controller
HEAT
Remote controller BRemote controller B
1
2
3
4
5
9
10
11
12
13
14
15
16
17
22
23
24
25
19
20
21
8
18
7
6
Control the lightening and extinguishing
of the indoor LED display board.
3. SWING display
8.
9. TURBO button
10. HEAT button
11. COOL button
12. AUTO button
13. FAN SPEED button
14. TIMER button
15. SLEEP button
17. LIGHT button
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button
23. EXTRA FUNCTION button
24.CANCEL/CONFIRM button
AUTO
Function: Setting and cancel to the
timer and other additional functions.
Display
circulated
Operation mode
Remote controller
QUIET TURBOSLEEP
Supplemented
electrical
heating HEALTH
Additional functions display
Function: Health--- FAN---
Healthy airflow
position1---
--- Healthy airflow position 2---
Right & left air airflow--- A-B yard---
function
)-- QUIET--- Refresh air( reserved
--- Fahrenheit/Celsius mode conversion
HEAT
Low-Temperature Heating Operation Down to 10℃
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
(adjust left and
ow)
Vertical blade
right air fl
Air Purifying FilterInlet (inside)
Emergency
Switch
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Outlet
Inlet grille
6
4
2
1
5
3
(inside)
Power indicator
Timer mode indicator
Operation mode indicator
(Lights up when unit starts.)
(Lights up whenTimer operation is selected.)
(lights up when the compressor is on.)
Remote signal receiver
(A beeping sound is generated when a signal
from remote controller isreceived.)
Ambient temp display
When receiving the remote control signal, display the set
temperature and in the rest time the room temperature is
displayed and this room temperature is only for reference.
7
11
10
8
9
Anion generator
12
9
10
11
12
13
13
2
Operation
Unit start / stop
1
3
2
2
Press FAN button.
Remote controller:
Press button
Every time the button is pressed, temp.setting
increase 1o
C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1
oC,if kept depressed, it will
decrease rapidly
Select a desired temperature.
3.Fan function
2.Select temp.setting
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
1. Unit start
Press ON/OFF on the remote controller, unit starts.
/
Remote controller
changes as follows:
LOW MED HI AUTO
Display
circulated
Air Flow Direction Adjustment
1.Status display of air flow
When restart after remote turning off, the remote
return to the previous
2.Left and right air flow adjustment
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
adjusted to left or
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.
at air outlet if all vertical louvers are
right.
mode ,
controller will automatically
Note:
set swing position.
Press button to enter additional options, when
cycle display to , will flash. And then press
enter to Left and right air flow function.
(This function is unavailable on some models.)
COOL/DRY:
HEAT: Initial state
Press button to enter additional options, when
cycle display to , will flash. And then press
enter to up and down air flow function.
Press button. For each press,changes as follows:
Remote controller:
Press button. For each press,changes as follows:
Remote controller:
COOL/DRY/HEAT:
For each press button fan speed
In HEAT mode,warm air will blow out after a short
periodof the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
Cooling only unit do not have displays and functions
related with heating
Display Board
Remote
Controller Note
COOL
DRY
HEAT
FAN nothing
In DRY mode, when room temperature becomes
lower than temp.setting+2oC,unit will run intermittently
at LOW speed regardless of FAN setting.
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according
to room temperature.
air conditioner automatically adjusts the fan speed
temperature.
When FAN is set to AUTO, the
according to room
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.
Operation
Mode
AUTO
Remote controller A:
Remote controller B:
Press button to enter additional options, when
cycle display to , will flash. And then press
enter to FAN function.
Loading of the battery
1
2
3
4
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with the" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
type fluorescent lamp or
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.


Product specificaties

Merk: Haier
Categorie: Airco
Model: HSU-09LEK13/R2(DB)

Heb je hulp nodig?

Als je hulp nodig hebt met Haier HSU-09LEK13/R2(DB) stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Airco Haier

Haier

Haier AS26FBBHRA Handleiding

11 November 2024
Haier

Haier AS35FBBHRA Handleiding

11 November 2024
Haier

Haier QPFA10 Handleiding

5 November 2024
Haier

Haier QHC18 Handleiding

5 November 2024
Haier

Haier HWR05XCR Handleiding

5 November 2024
Haier

Haier QHM15 Handleiding

5 November 2024
Haier

Haier HPFD12XHP Handleiding

5 November 2024
Haier

Haier QHM18 Handleiding

5 November 2024
Haier

Haier QHM10 Handleiding

5 November 2024
Haier

Haier QPSA13 Handleiding

5 November 2024

Handleiding Airco

Nieuwste handleidingen voor Airco