Haier HSU-09HEG03/R2(DB) Handleiding

Haier Airco HSU-09HEG03/R2(DB)

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Haier HSU-09HEG03/R2(DB) (8 pagina's) in de categorie Airco. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
Please read this operation manual before using the air conditioner.
โ—
Keep this operation manual for future reference.
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
0010538410
HSU-09HEG03/R2(DB)
6
1
2
5
Contents
PARTS AND FUNCTIONS
OPERATION
MAINTENANCE
CAUTIONS
TROUBLE SHOOTING 7
HSU-12HEG03/R2(DB)
HSU-18HEG03/R2(DB)
HSU-24HEG03/R2(DB)
HSU-09HEK03/R2(DB)
HSU-12HEK03/R2(DB)
HSU-18HEK03/R2(DB)
HSU-24HEK03/R2(DB)
Outdoor Unit
๎€—
Loading of the battery
1
2
3
4
Parts and Functions
Indoor Unit
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
Remote controller
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with th
e" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
type fluorescent lamp or
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
Please be subject to the actual produce purchased the
above picture is just from your reference
4
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
Please be subject to the actual produce purchased the
above picture is just from your reference
1. Mode display
2. Signal sending display
4. FAN SPEED display
5. LOCK display
6. TIMER OFF display
TIMER ON display
LO MED HI
7.TEMP display
16. LOCK button
Used to lock buttons and LCD display.
25. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
22. HOUR button
Operation mode AUTO FANCOOL DRY
Remote controller
HEAT
1
2
3
4
5
9
10
11
12
13
14
15
16
17
22
23
24
25
19
20
21
8
18
7
6
Control the lightening and extinguishing
of the indoor LED display board.
3. SWING display
8.
9. QUIET button
10. HEAT button
11. COOL button
12. AUTO button
13. FAN SPEED button
14. TIMER button
15. HEALTH button
17. LIGHT button
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button
23. EXTRA FUNCTION button
24.CANCEL/CONFIRM button
AUTO
Function: Setting and cancel to the
timer and other additional functions.
Display
circulated
Operation mode
Remote controller
QUITE POWERSLEEP
Supplemented
electrical
heating HEALTH
Additional functions display
Healthy function is not available for some units.
Function: Air sending--- Healthy
airflow position1--- Healthy airflow
position 2 --- Restore the original
flap position --- Right & left air airflow
--- A-B yard---10 and heating symbol
displayed simultaneously--- Sleeping
--- Electrical heating--- Refresh air
(reserved function) --- Power ---
Fahrenheit/Celsius mode conversion
Air Purifying Filter(inside)
Inlet
1Inlet grille
2
Outlet
4
(adjust left and right air flow)
Vertical blade
6
Display board
Horizontal flap
(adjust up and down air flow.
Don't adjust it manually) Emergency Switch
7
8
3
5
1
2
4
6 5 7
3
1
EK3
8
1
2
3
4
5 86 7
EK1 display board
EK3 display board
Display board
When receiving the remote control
signal,display the set temperature
and in the rest time the room
temperature is displayed and this
room temperature is only for reference.
Signal receiver hole
ON/OFF display
Ambient temp.display
TIMER ON/OFF display
TIMER ON-OFF display
SLEEP display
Note to the power failure resume:
Press the sleep button ten times in five seconds and enter function
after hearing four sounds.And press the sleep button ten times
within five seconds and leave this function after hearing two sounds.
EK1
COOL\HEAT\DRY\AUTO display
45
4
5
6RUNNING display
2
4
6
Operation
Air Flow Direction Adjustment
Press FAN button. For each press, fan speed
follows:
Remote controller:
Press button
Every time the button is pressed, temp.setting
increase 1o
C,if kept depressed, it will increase
rapidly
Every time the button is pressed, temp.setting
decrease 1
oC,if kept depressed, it will
decrease rapidly
Select a desired temperature.
4.Fan speed selection
3.Select temp.setting
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
1. Unit start
Press ON/OFF on the remote controller, unit starts.
๎€’
Base Operation
Remote controller
1.Status display of air flow
When restart after remote turning off, the remote
memorize the previous
Move the vertical blade by a knob on air
to adjust left and right direction referring to Fig.
2.Left and right air flow adjustment(manual)
Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
adjusted to left or
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY
otherwise, condensate water might occur.
conditioner
Emergency operation and test operation
at air outlet if all vertical louvers are
right.
mode ,
controller will automatically
Note:
set swing position.
changes as
Operation
Mode
Remote
Controller Note
In DRY mode, when room temperature becomes lower
than temp.setting+2oC, unit will run intermittently at LOW
speed regardless of FAN setting.
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according to
room temperature. When FAN is set to AUTO the air
conditioner automatically adjusts the fan speed according
to room temperature.
In FAN operation mode , the unit will not operate in COOL or
HEAT mode but only in FAN mode, AUTO is not available in
FAN mode. And temp. setting is disabled. In FAN mode,
sleep operation is not available.
Emergency Operation:
Use this operation only when the remote controller is defective
or lost, and with function of emergency running, air conditoner
can run automatically for a while.
When the emergency operation switch is pressed, the " Pi "
sound is heard once, which means the start of this operation.
When power switch is turning on for the first time and
emergency operation starts, the unit will run automatically in
the following modes:
Room
temperature Designated
temperature
Timer
mode Fan
speed
Operation
mode
Above 23 oC
Below 23 o
C 23 oC
26oC
No
AUTO
AUTO
COOL
HEAT
No
It is impossible to change the settings of temp. and fan speed,It
is also not possible to operate in timer or dry mode.
temperature is below 16oC, do not use it in the
Test operation:
Use this switch in the test operation when the room
normal operation.
your finger from the switch: the cooling
Continue to press the test operation
switch for more than 5 seconds . After
you hear the "Pi" sound twice, release
Test operation switch is the same as emergency switch.
operation starts with the air flow speed "Hi".
Under this operation mode,the fan motor of indoor
unit will run in high speed.
๎€”
๎€—
๎€–
๎€–
LOW MED HI AUTO
2. Select operation mode
๎€•
COOL button:Cooling mode
HEAT button: Heating mode
DRY button: Dehumidify mode
Display
circulated
DRY
COOL
AUTO
HEAT
FAN
In HEAT mode, warm air will blow out after a short
period of the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
test operation
switch
Pi Pi
Pi
emergency
operation switch
๎€–'
2
Pos.1 Pos.2 Pos.3
Pos.4 Pos.5 Pos.6 (Auto swing)
cooling mode:from pos.1 to pos.4 and pos.6
heating mode:from pos.5 to pos.1 and pos.6

Product specificaties

Merk: Haier
Categorie: Airco
Model: HSU-09HEG03/R2(DB)

Heb je hulp nodig?

Als je hulp nodig hebt met Haier HSU-09HEG03/R2(DB) stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Airco Haier

Haier

Haier KFR-35GW/11WEA22AU1 Handleiding

10 December 2024
Haier

Haier KFR-32GW/11WEA22AU1 Handleiding

10 December 2024
Haier

Haier KFR-35GW/05KBP22A(DS) Handleiding

10 December 2024
Haier

Haier JA-18T Handleiding

9 December 2024
Haier

Haier JA-SP25E Handleiding

9 December 2024
Haier

Haier JA-SP25G Handleiding

9 December 2024
Haier

Haier JA-18L Handleiding

9 December 2024
Haier

Haier JA-16M Handleiding

9 December 2024
Haier

Haier JA-18U Handleiding

9 December 2024
Haier

Haier JA-SP25V Handleiding

9 December 2024

Handleiding Airco

Nieuwste handleidingen voor Airco

Meireles

Meireles MAC 12 W Handleiding

22 December 2024
Meireles

Meireles MAC 18 W Handleiding

22 December 2024
LG

LG PM12EP Handleiding

21 December 2024
Svan

Svan SAAS1200W Handleiding

20 December 2024
Argoclima

Argoclima LOKI PLUS WF Handleiding

18 December 2024
Universal Blue

Universal Blue Grandvalira II 1750 Handleiding

18 December 2024
Universal Blue

Universal Blue Grandvalira II 3000 Handleiding

18 December 2024
Mitsubishi

Mitsubishi WRK20MB2 Handleiding

14 December 2024
Mitsubishi

Mitsubishi SKM25ZSP-W Handleiding

14 December 2024
Mitsubishi

Mitsubishi MSZ-GV2217 Handleiding

14 December 2024