Haier ES15V-E1 Handleiding

Haier Ketel & boiler ES15V-E1

Lees hieronder de 📖 handleiding in het Nederlandse voor Haier ES15V-E1 (2 pagina's) in de categorie Ketel & boiler. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
1 2
ES10V-E1(H)
ES15V-E1(H)
ES25V-E1(H)
Haier Home Water eateH r
Instruction manual
0040503116
Please read this Instruction Manual carefully before use.
Please retain this manual for future reference.
Troubleshooting
Specications
Introduction of exterior and a essoriescc
Technical parameters
Electrical Diagram
Model a b c d e
ES10V-E1 (H) 300mm 338mm 456mm 152mm 100mm
ES15V-E1 (H) 335mm 374mm 495mm 152mm 100mm
ES25V-E1 (H) 370mm 409mm 546mm 152mm 100mm
Note: 1. The margin of error for the above parameters (measurements, weight) is ±10%.
2. Water tempe ture indicator is not a precision thermometer. It consists of three areas ra
denoted by blue; orange and red, which indicate the temperature of water in the
inner chamber from low to high respectively.
(Fig.2)
Remarks:
The permitted error limit of net weight above is
±
10%.
Item Unit ES10V-E1 (H) ES15V-E1 (H) ES25V-E1 (H)
Rated voltage V 230 230 230
Rated frequency Hz 50 50 50
Rated pressure MPa 0.80 0.80 0.80
Power W 2000 2000 2000
Net weight kg
Rated tempe turera oC 75 75 75
Volume L 10 15 25
Waterproof ade / IPX4 IPX4 IPX4gr
Mixing factor %
Tap water pressure MPa s n Pa s n Pa s n PaNo les tha 0.05M No les tha 0.05M No les tha 0.05M
Average temperature of hot ter outletwa oC
Re-heating time
(a temperature rise of 50oC) min
Diameter of power wire mm23×1.5 3×1.5 3×1.5
L : Brown wire
N : Blue wire
MT : High temperature limiter
BT : Thermostat
HL : Heating indicator
EH : Heating element
E : Yellow/green wire
Symptom Things to Check Solutions
No water
1
Whether the ter supply wa
has stopped or whether the
water pressure is too low
Check
2Whether the water-
usage point is blocked or
whether the hot water
valve is opened
Check and clear
Only cold
water but
the heating
indicator light
is lit
1Whether hot water outlet
is opened Check and open
2Whether the water
temperature is adjusted
Increase the temperature to the required
value. Once the water is heated to the pre-set
tempe ture, control ow volume of cold and ra
hot ter using the moderating mixing valve.wa
3Heating time is too short
and set tempe ture is ra
not achieved
Continue heating
4Whether heating pipe is
damaged
Conr thi nm s is ot d e o he u t t reaso ns123 ,
then contact Maintenance Department
On y oll c d water
and e heth ating
indicator light
is not lit
1Whether power is
properly connected Check power socket
2Whether thermostat is
out of control
Conrm this is not due to the reasons
1,
then contact Maintenance Department
Heating
indicator light
is
on all the time
1Water has not reached
the set temperature Continue heating
2Whether thermostat is
out of control
Conrm this is not due to the reasons 1,
then contact Maintenance Department
Water volume is
sometimes large
o sm lr al , or water
is s meo times hot
or cold
Whether water pressure is
stable
Set lower mixing valve or ensure water
pressure is stable before use
Sma ll hot water
outlet volume
1Whether the present
temperature setting is
too low
Calibrate using the method stipulated in the
Instruction Manual
2Whether ter pressure is wa
excessive Set lower mixing valve
Safety Notices (Please read before use)
Prohibited Compulsory
Matters Essential Matters
our Service Cent nc ter o e he wat ater he er does
not work r p ope y emrl or its urn b t smell.
230 /50 z i depenV H n dent ower rce p sou
mu usst be ed at es.all tim
To r fety ensu e sa , t e h water heater shou ld
be nneco cted to indepe den nt s s ocket (do
no s pte reliabl ar gt u e ada rs) with, e e thin . In
a t ower et mu conform dd ioit n he p sock st
t nao tional ndards Us o watsta . e f er heater
without re bl rt i tric prlia e ea hing s s tly ohibited.
Us n imet te pe mult er o hecc k w ether he lih t ve
line and neutr ial l ne e ar reve e.rs
Do not dam d wiruse age e pand ower
socket. Pr p om tly cl an th dust one e the
power p g lu and soc t.ke
Check he pt ower met n her a d t e electric
wir die's ameter to ur ens e that t ey h co y mpl
with h rated urrent f t e c or th e water
electr ia tic n o eck t e ech h lectri ircuit.c c
nea the r wat ater i trictlyer he s s prohibited.
Do not touch t uhe pl g with wet s, hand
an sud e mak re that t e h water heater, plug
so docket not c into con ct ome ta with
water. f I they are accid tallyen wet, heyt
mu chst be ecked by professional rsons pe
a nted by our c pan forppoi om y be e using,
in order t revento p electrocution.
Do not connect to ower en p wh installing
or ai rep ring t e h water heater.
Non-professionals are strictly prohibited
from carrying out repairs, maintenance,
dismantling or revamping of the ter wa
heater.
Installati ter at utd s on of wa he er o oo irs
strictl roh ted.y p ibi
Do no installt t e h water heat i nvironment er n ean
w ch chi is sus ep e tibl to ice-formati Ic wi on. e ll
ca h conta er and water touse t e in pipe break,
le inad g to scal and water l kage.ding ea
Pl sea e t ke p eca r autionar m ures y eas
durin col weat rg d he , o dein r r to prevent
damage er to twa heat ro rer f m f ee inz g.
I h oft ower l df t e s p cab e d ageis am , it
from t e ufah man cturer M ntenance s or ai
D rt n rder t avoepa me t oin o id anged r.
Take ca e not be sr to calded y b heat ter. ed wa
· Touching of ot er h wat valve an pipes d is
strictl roh ted.y p ibi
·
Ma sur to e hke e ch ck t e er wat temperature
befor use s onle , u e y w en ih t f comfor e.eels tabl
D o t ro h tero n t use wa er f m t e wa heater
for drinking or similar r s. pu pose
wat at w n uer he er as ot sed r n fo a ext d ende
pe d of trio ime rai h t heater of . D n t e wa er
al tl wa er a ordi to tcc ng he instruction n s i
th hae c pter l M nte ce.on C ea g nin and ai nan
A: Water inlet pipe
B: Water outlet pipe
C: Inner chamber
D: Heater
E: Magnesium rod
F: Temperature
measurement pipe
G: Wall-mount support
H: Washer
Meanings of Icons
Earthing
For nbidde
For enbidd
For denbid
For denbid
For enbidd
For denbid
For enbidd
Warning
Warning
War inn g
War inn g
Warning
Warning
Ca onuti
Caution
Caution
For enbidd
ＣＳＨ１０Ｄ００３８＿ＥＮ．ｉｎｄｄ　　　１ ５／２５／２０１０　　　４：２７：１５　ＰＭ
2.7 0.9 3.0
69
6964
811 14
20 25 45
e is ≥0.80M
5 6
3 4
Mu n l b n r c anst be i sta led y perso nel in ou omp y's -sa epa me t or esi ed nstAfter les D rt n d gnat i all tion pe sona r nel.
The water heater is wall-mounted type.
Determine the installation position of the ter heater. Based wa
on the measurements indicated in Fig. 2, use impact drill to
drill two holes of 12mm in diameter and 65mm in depth.
Insert the expandable hooks into the holes and ensure that
they are securely xed. Lift the water heater and slip its wall-
mount support onto the expandable hooks (as show in Fig.1).
Check to make sure the machine is securely suspended.
For a essories such as safety valve, please refer to the cc
“Installation of Safety Valve” (for reference only). Make sure to
seal the joints with Teon tapes to prevent water leakage.
For ease of installation and removal of water heater, we
would recommend that G1/2 loose joints be installed at
appropriate locations on the ter inlet and outlet pipes of the water heater. Determine the position of wa
the hot ter supply. Connect the ter inlet and outlet pipe together with the ter pipe to the positions wa wa wa
reserved for use of hot water. Hot ter pipe should preferably not be too long in order to prevent heat loss.wa
Note: Make sure that the ter heater is securely attached to the hook before letting it go; otherwise it wa
may drop and cause injury or property damage.
When installing the ter heater, certain space should be reserved (not less than 250mm from the top wa
and bottom and not less than 700 mm from the front and the sides), for ease of subsequent maintenance
and repair. If the water heater was to be built into clip boards, the bottom section of the clip board should
be movable for ease of removal of plastic cover during maintenance.
Make sure the pressure on the water inlet is not less than 0.05MPa, and not more than 0.75MPa.
The water heater should be installed indoors in a place where the ambient temperature is above 0
o
C. The
pipes uld be c e d t. The hot ter et d not be too f away from the point of age. If e sho los ly lai ou wa outl shoul ar us th
distance exceeds 8 meters, the hot water pipe should have insulation protection, in order to prevent heat loss.
The wall on which the ter heater should be strong such as it is able to withstand fourth the weight of the wa
water heater when lled with water. If the wall was not weight-bearing wall or made of hollow bricks, adequate
protective measures such as addition of support and high-strength wall screw with back panel should be adopted.
The water heater should be installed in places such as it is easy to use and maintain and with oor drain,
in order that it will not cause damage to nearby facilities or those in the lower levels during a leakage
of the water tank or water pipe. It should not be installed over toilet bowls, bathtub, wash basin or door
frame in order that users do not feel oppressed or insecure.
Power socket for the water heater should be installed in dry places which do not easily come into contact with
Do not reverse the installation for the ter inlet and outlet. The safety valve should be installed in the wa
designated position and should not be moved without permission. The safety valve's pressure-relief hole
should be connected to the atmosphere and free from blockage at all times.
Use pen multimeter to check whether the live line and neutral line are reverse. Turn on power supply only
when you have ensured that the heater is lled with ter and that there is no water leakage. The power wa
supply should also conform with requirements.
Safety reminder: In order to prevent accidents, please use our company's accessories during installation. Do not
replace them on your own or use substitutes. Please make sure to contact our Maintenance Department if the pipes
or a essories are damaged and replace them with the accessories supplied by our company. Our company shall not cc
be liable for any direct or indirect losses caused as a result of accidents for failure to comply with the aforesaid.
All ter pipes should be installed by qualied water pipe installation workers. The pipelines should wa
comply with the national standards and regulations on the prohibition of prevention tools to draw ter wa
to water source pipelines by way of inverse siphon, as well as local building codes.
Installation method
Installation Precautions
Fig.1
Wall-mount support
Expandable
hook
Instruction manual
Operation
After completion of installation, make sure to turn on the water inlet valve and mixing valve
since there is no water in the inner chamber. Turn the mixing valve to the maximum for hot
Inspect all connections to ensure that there is not ter leakage before connecting to power.wa
Adju he wate t perast t r em tu nobre k at the otb tom
of the water heater to set the temperature.
Maximum ter temperature setting is 75wa
o
C
Temperature adjustment knob: Slowly turn the knob clockwise
to raise the temperature setting. The knob will not continue to
turn once it reaches maximum temperature setting. Turn it anti-
clockwise gradually to reduce the tempe ture setting. Once the ra
mi imu ttin m tempe ture sera ng is reached, the ter heater's power wa
If the heating indicator light is lit, it means that the water heater is heating.
Observe the water temperature indicator for
the current water temperature.
Wate a n b o ar he ti g will e n st nd y au omb t atically
when the water temperature reaches the set temperature. Once it lowers
to certain temperature, power will be automatically connected.
Do not connect the power before lling the inner chamber with water in order to
prevent damage to the water heater.
Adjust the ter temperature to the suitable level before use in order to prevent scalding.wa
Insofar as there is adequate hot water, set a lower tempe ture to reduce heat loss, high ra
temperature corrosion and scaling. This will extend the water heater's lifespan.
To avoid danger caused by accidental resetting of the heating breaker, the power for
the heat cannot be supplied by timer and other external switch devices or connected to
circuit with frequent switching for facility use.
Observe the water drainage of the safety valve's pressure-relief hole.
When the water pressur Pa and the pressure-relief hole on the safety valve emits
large volume of water, it means that the ter pressure is excessive. In such case, please notify wa
the After-sales Department.
Things to note during use
Wa r te
t u emperat re
knob
He ngati
indica or light t
Water temperature indicator
Cleaning
Check
Not in use for an extended period of time
Warning!
The water heater must be repaired or maintained by qualied professionals. Improper
methods may cause serious injury or damage to property.
Cleaning and Maintenance·Packing List
External cleaning
Take a wet cloth and dab it with small quantity of neutral deterge . Lightly wipe the ter heater. nt wa
Do not use petrol or other solvents. Finally use a dry cloth to wipe,
make use to dry the water
heater thoroughly. Make sure not to use detergents containing abrasive agents (e.g. toothpaste); acidic
substances; chemical solvents (e.g. alcohol) or polish to clean the water heater.
Internal cleaning
In order to ensure that the ter heater works eciently, the heating pipe and inner chamber should wa
be cleaned once every three years. Take care not to damage the exterior of the heating pipe or the
protective layer on the surface of the inner chamber. Depending on the local water quality and the
usage habit, the magnesium rod might need to be regularly changed. If maintenance is required,
please contact the local Maintenance Departme .nt
When the water heater is in use, the safety valve should be checked once every month. To check it, turn
the safety valve's small handle on the side of the ter inlet pipe (take care not to hurt your hand). If there wa
is ter owing out, the safety valve is working normally. Please contact the local After-sales Department wa
if no ter ows out. In the event of damage to the safety valve, please replace it with a safety valve of wa
similar specications.
Regularly engage service personnel to carry out safety inspection and promptly clear the water heating pipes
of the ale. Che o e c mp of e gne um rsc ck als th onsu tion th ma si od it sum on; change if con pti becomes exces ve.si
If the ter heater is not used for an extended period of time, please carry out the following steps:wa
Screw the ter drainage pipe to the safety valve's pressure-relief hole; turn on the safety valve handle.wa
Turn the hot water valve to the maximum (at the same time unscrew the sprinkler head soft pipe from the ter wa
outlet valve; take care not be scalded by hot water), drain the inner chamber of water.
When the water heater needs to be used again, our recommendation is to open hot water valve before
switching on the power in order to prevent accidents. Allow any gas that may be trapped in the pipe to be
discharged. Do not smoke or allow other exposed re to be near the opened valve. At the same time, make
sure to carefully examine all the parts of the ter heater and ensure that they are in a perfect condition. wa
Make sure to ll the inner chamber with water before use.
Packing list
Install the safety valve which has a rated pressure of 0.80MPa (its connection
is G1/2) into the ter inlet pipe with the arrow on the safety valve pointing wa
at the water heater. When the ter heater is heated by electricity, a small wa
amount of water will ow from the safety valve's pressure-relief hole due to
the expansion of water in the heater. This is normal. The pressure-relief hole
should be connected to the atmosphere and free from blockage at all times.
Installation method for safety valve's drainage pipe: Attach an end of the
water drainage pipe onto the pressure-relief hole on the safety valve. You
may cut the ter drainage pipe to make it shorter, or extend it depending on the situation. wa
Connect to the other end of the ter drainage pipe to the lower water outlet. This will prevent wa
the ter from the pressure relief hole from splashing. The ter drainage pipe connected to the safety wa wa
valve should be installed in a slanted manner and in an environment which is not prone to frost.
Note: If your ter heater is not installed in a bathroom with sewer, our recommendation would be that wa
you add safety valve water drainage pipe.
Installation instruction
Description of parts
Installing safety valve
Small handle
for safety valve
Pressure-relief hole (connected
to water drainage pipe)
Sprinkler head
Cold water inlet
Hot water
outlet
Hot water pipe
Cold water pipe
Safety valve
Direction of cold water
Direction of hot water
Wa r te
t u emperat re
knob
He ngati
indica or light t
Water temperature indicator
Product Model No.
Electric Water
Heater (unit)
Safety Valve/Water
Drainage Pipe (set)
Instruction Manual
(book)
Expandable Hook
(pcs.)
ES10V-E1 (H)
1 1 1 2
ES15V-E1 (H)
ES25V-E1 (H)
Quantity Name of
parts
(Fig. 3)
󰷅󰷅󰷅 󰷅󰷅󰷅󰷅

Product specificaties

Merk: Haier
Categorie: Ketel & boiler
Model: ES15V-E1

Heb je hulp nodig?

Als je hulp nodig hebt met Haier ES15V-E1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Ketel & boiler Haier

Haier

Haier HP200M1-U1 Handleiding

14 Maart 2024
Haier

Haier GV100REMB Handleiding

22 November 2023
Haier

Haier ES30V-A3 Handleiding

22 November 2023
Haier

Haier ES50H-CK1 Handleiding

22 November 2023
Haier

Haier JSQ25-13WPT(12T) Handleiding

6 Juli 2023
Haier

Haier ES60H-S5K(E) Handleiding

30 Juni 2023
Haier

Haier ES50H-A3(E) Handleiding

29 Juni 2023
Haier

Haier EC6003-YT3 Handleiding

29 Juni 2023
Haier

Haier JSQ20-T(12T) Handleiding

26 Juni 2023
Haier

Haier GV270REMB Handleiding

22 Juni 2023

Handleiding Ketel & boiler

Nieuwste handleidingen voor Ketel & boiler

Panasonic

Panasonic DH-6VS1 Handleiding

25 November 2024
Philips

Philips AWH1201 Handleiding

24 November 2024
Philips

Philips AWH1211 Handleiding

24 November 2024
Philips

Philips AWH1200 Handleiding

24 November 2024
Philips

Philips AWH1205 Handleiding

24 November 2024
Philips

Philips AWH1204 Handleiding

24 November 2024
Rinnai

Rinnai EHPA250VMAWH Handleiding

21 November 2024
Rinnai

Rinnai ECF29i50 Handleiding

21 November 2024
Rinnai

Rinnai ECF19i60 Handleiding

21 November 2024
Rinnai

Rinnai FM10NA Handleiding

20 November 2024