Gorenje DK63CLB Handleiding

Gorenje Afzuigkap DK63CLB

Lees hieronder de 📖 handleiding in het Nederlandse voor Gorenje DK63CLB (75 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/75

ENG - Instructions for use

IT - Istruzioni per l’uso

SLO - Navodila za uporabo

POL

DA - Brugsanvisning

LT - Lietošanas instrukcijas

ET - Kasutusjuhised

NO - Instruksjoner for bruk

AL - Udhëzimet për përdorim

SLO - Navodila za uporabo

AR -

- Gebrauchs

CRO - Upute za upotrebu

RU -

FR - Francais

- Türkçe

ENGLISH

DESCRIPTION

The unit can be found in filtering hoods or in exhaust hoods. In the Filtering hoods (Fig. 1) the air and steam

taken up by the unit are purified with charcoal filters and returned to the environment through the aeration grids

on the side of the flue. WARNING: When using filtering hoods, both charcoal filters and an air deflector (A) must

be used. Located in the lower part of the flue, this deflector recycles the air to the environment. The charcoal

filters are not supplied. In the Exhaust hoods (Fig .2) an exhaust duct conveys the steam and cooking odors

directly outside through the wall/ceiling. Therefore they do not require charcoal filters.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in

electrical hazards.

INSTALLATION

To facilitate installation, before starting remove the grease filters: press inward on the clamp at the handle

and pull the filter downward (Fig. 3).

Mount the plate of the electrical system (depending on the model) fixing it with 2 screws and 2 metal washers

(Fig. 4).

Wall fitting (Fig. 5): making use of the appropriate drilling jig, apply the supplied blocks into the wall, and

remember the distance between the hood and the cooktop must be at least 65 cm. Insert two of the supplied

screws so that the apparatus can be hooked onto these ones by means of the holes provided on the appliance

(use the holes A; if the hood have the holes A and C, use only the holes C). Once the apparatus is hooked,

fix it definitively to the wall using the two other screws and the holes made at its bottom (B). To avoid damage

make exclusive use of the holes already prepared on the hood.

Securing the telescopic flue: Basic installation requirements: – Set the electrical power supply within the space

covered by the decorative flue. – If your unit is installed in an Exhaust hood, prepare the air exhaust hole.

Place bracket (W) 50 mm from the ceiling and position this on the vertical of your hood, with the aid of the notches

on the centre of the bracket (Fig. 6); using a pen, mark the 2 holes on the wall and then make the holes and

fit the screw anchors provided and proceed to secure the bracket using the 2 screws (provided).

Exhaust hoods: connect the disposal duct to the air evacuation pipe of the hood; use a flexible pipe and lock

it to the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make all

power connections to the hood by means of the power cable. Take 2 assembled flues and place these on the

upper surface of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2

screws (Fig.7).

Filtering hood: make all power connections to the hood using the power cable. Fasten the air baffle to the lower

flue as shown in Figure 8, using the 2 screws. Take 2 assembled flues and place these on the upper surface

of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig.7).

Also remember that charcoal filters must be used in the case of the filtering version; check to see whether such

filters are already fitted; if necessary, proceed to fit as follows, depending on the model type purchased:

- if the hood features round charcoal filters (Fig. 9), fit the charcoal filter by turning anti-clockwise.

- if the hood features a panel type charcoal filter (Fig. 10), remove the two metal filter retainers (M) and position

the charcoal filter inside the grease filter; fit the two filter retainers back on again to secure the charcoal filter.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls shown in Fig. 11: Button A: light switch. Button B: first speed motor ON/OFF switch. Button C: second

speed switch. Button D: third speed switch. E: motor on light. THE MOTOR FUNCTION WARNING LIGHT (E) IS

NOT PRESENT IN SOME MODELS.

Controls shown in Fig. 12: Button A: Light switch; position 0: light off; position 1: light on. Button B: Motor

switch; position 0: motor off; position 1-2-3: motor on at speed I, II and III. C: Motor pilot lamp.

Controls shown in Fig. 13: Button A: turns the LIGHTS off. Button B: turns the LIGHTS on. Button C: decreases

speed down to minimum speed. If pressed for 2" the motor is turned off. Button D: activates the motor (calling

the last speed used) and increases the speed until reaching maximum. Button E: FILTER ALARM/TIMER RESET:

when pressing the key during display of the filter alarm (motor off) it resets the hour counter. When pressing the

key when the motor is running, the TIMER is activated and the hood will automatically be switched off after 5

minutes.

L1) The 4 green LEDs indicate the running speed.

L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that

the TIMER has been activated with the key E.

FILTER ALARM: After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned.

After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and

the charcoal filters replaced. After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter

(RESET) by pressing the key E during display of the filter alarm.

Controls shown in Fig. 14: Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot

Product specificaties

Merk:	Gorenje
Categorie:	Afzuigkap
Model:	DK63CLB
Soort bediening:	Knoppen
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht:	10300 g
Breedte:	600 mm
Diepte:	500 mm
Hoogte:	1140 mm
Netbelasting:	290 W
Geluidsniveau:	64 dB
Energie-efficiëntieklasse:	D
Jaarlijks energieverbruik:	94 kWu
Gewicht verpakking:	13100 g
Breedte verpakking:	700 mm
Diepte verpakking:	465 mm
Hoogte verpakking:	630 mm
Soort:	Muurmontage
Motor vermogen:	- W
Uitlaat aansluiting diameter:	150 mm
Motor inbegrepen:	Ja
Aantal motors:	1
Materiaal behuizing:	Staal
Maximale afzuigcapaciteit:	545 m³/uur
Afzuigmethode:	Afvoerend/recirculerend
Fluid dynamic efficiency class:	D
Verlichtingefficiëntieklasse:	A
Vetfilterefficiëntieklasse:	E
Geluidsniveau (lage snelheid):	54 dB
Aantal lampen:	2 gloeilamp(en)
Type lamp:	LED
Soort vetfilter:	Aluminium
Wasbaar filter:	Ja
Hoogte (min):	810 mm
Hoogte (max):	1140 mm
Vermogen lamp:	10 W
Maximum hercirculeringsvermogen:	342 m³/uur
Aantal filters:	1 stuk(s)
Aantal snelheden:	3
Stroom:	10 A
Verlichtingspositie:	Rug
Intensieve stand:	Nee
Uitlaat locatie:	Boven
Vaatwasserbestendig filter:	Ja
Hoogte zonder schoorsteen:	36 mm
Boost functie:	Nee
AC-ingangsspanning:	230 - 240 V
AC-ingangsfrequentie:	50 Hz