Gladiator GAJG36FDYG Handleiding

Gladiator Kast GAJG36FDYG

Lees hieronder de 📖 handleiding in het Nederlandse voor Gladiator GAJG36FDYG (20 pagina's) in de categorie Kast. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20
PREMIER JUMBO CABINET
Assembly Instructions
ARMARIO GIGANTE DE
ALTA CALIDAD
Instrucciones de ensamblaje
GRANDE ARMOIRE
(PREMIER JUMBO)
Instructions d'assemblage
TABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES
CABINET/LOCKER SAFETY ........................ 2
PARTS ........................................................... 2
ASSEMBLY INSTRUCTIONS........................ 3
INSTALLATION INSTRUCTIONS................. 6
WARRANTY ................................................... 7
SEGURIDAD DEL ARMARIO .......................8
PIEZAS ............................................................8
INSTRUCCIONES DE ENSAMBLAJE ..........9
INSTRUCCIONES DE INSTALACIÓN........ 12
GARANTÍA ................................................... 13
SÉCURITÉ DE L’ARMOIRE.........................14
PIÈCES..........................................................14
INSTRUCTIONS D'ASSEMBLAGE .............15
INSTRUCTIONS D'INSTALLATION............18
GARANTIE ....................................................19
W10130911C
I T ' S T I M E T O R E T H I N K T H E G A R A G E . ®
E S T I E M P O D E V O L V E R A P E N S A R E N E L G A R A G E . ™
L E G A R A G E R E P E N S É .
2
CABINET/LOCKER SAFETY
PARTS
F1
F2
F3c
F7
F8
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
P2
P5mr
P5ml
P5mr
P3
P6
P7
P1
P1
AAA
BBB
DDD
EEE
CCC
P4
P8
P8
P8
3
ASSEMBLY INSTRUCTIONS
Cabinet Use Requirements
Intended for use in a garage.
Maximum weight limit is 50 lbs (22.7 kg) for each shelf.
Maximum weight limit is 300 lbs (136 kg) for the cabinet.
Unpack Cabinet Parts
1. Remove and verify the contents. Contents include a hex key, a
key, and the parts and fasteners shown in “Parts.”
2. Dispose of/recycle all packaging materials.
Assemble Cabinet
Gather the required tools before starting installation.
Tools Needed:
Tools Supplied:
IMPORTANT:
Two people may be required to complete the assembly.
As you assemble the cabinet, make sure the edges with the
holes are facing up.
If you are assembling the cabinet on the floor, fasten the eight
front corner bolts, two at each corner, after you stand the cabinet
upright.
1. Place side panel (P1) on a flat, firm surface so that the edge with
the holes is facing up as shown.
2. Insert the cabinet top (P2) between the edges of side panel (P1).
NOTE: Make sure the edges with the holes are facing up.
3. Align the holes and attach the top (P2) to side panel (P1) using
Hex-head bolts (F1) and the three ⁵⁄₁₆"
flange nuts (F2) as shown.
Do not tighten completely.
4. Position the other side panel (P1) so that the top (P2) is between
the edges of side panel (P1).
5. Align the holes and attach the top (P2) to the side (P1) using Hex-
head bolts (F1) and the three ⁵⁄₁₆"
flange nuts (F2) as shown. Do
not tighten completely.
6. Insert the cabinet bottom (P3) between the edges of the side
panels (P1).
NOTE: Make sure the edges with the holes are facing up.
7. Align the holes and attach the bottom (P3) to the sides (P1) using
Hex-head bolts (F1) and the three ⁵⁄₁₆" flange nuts (F2). Do not
tighten completely.
Attach Back Panels
IMPORTANT:
Attach the back panels starting at the top of the cabinet with
back panel (AAA) and working down to the cabinet bottom. Each
back panel will overlap the panel below.
Do not completely tighten the screws until all back panels are in
place.
1. Align back panel (AAA) with the holes in the cabinet top. Using
Phillips-head screws (F3c), attach back panel (AAA) to the
cabinet top and sides.
2. Slide the top of back panel (BBB) under the bottom of back panel
(AAA). Using Phillips-head screws, fasten back panel (BBB) to
the cabinet sides.
3. Repeat Step 2 for the remaining back panels ending with back
panel (EEE).
4. Using Phillips-head screws, attach each back panel to the panel
below.
NOTE: Using Phillips-head screws, attach panel (EEE) to the
cabinet bottom (P3).
5. Completely tighten all back panel screws starting with the sides
and continuing with the top, middle and bottom.
F1 F2
F1
⁵⁄₁₆
" Hex-head bolt (28)
F2
⁵⁄₁₆
" Flange nut (12)
¹⁄₂" Wrench
Phillips screwdriver
Level
■ ■Hex key Key
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
F3c
Phillips-head screw (34)
P1
P1P2
P3
P1
P2


Product specificaties

Merk: Gladiator
Categorie: Kast
Model: GAJG36FDYG

Heb je hulp nodig?

Als je hulp nodig hebt met Gladiator GAJG36FDYG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Kast Gladiator

Handleiding Kast

Nieuwste handleidingen voor Kast