Gigabyte GV-R485MC-1GH Handleiding

Gigabyte Videokaart GV-R485MC-1GH

Lees hieronder de 📖 handleiding in het Nederlandse voor Gigabyte GV-R485MC-1GH (39 pagina's) in de categorie Videokaart. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/39

AMD® Graphics Accelerator

User’s Manual

Rev. 104

mitted in any form without the expressed, written permission of .GBT

Trademarks

Third-party brands and names are the properties of their respective owners.

Notice

Please do not remove any labels on this graphics card. Doing so may void the warranty of this card.

Due to rapid change in technology, some of the speciﬁ cations might be out of date before publication of this this

manual. The author assumes no responsibility for any errors or omissions that may appear in this document nor

does the author make a commitment to update the information contained herein.

Rovi Product Notice:

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual

property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended

for home and other limited viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering

or disassembly is prohibited.

- 2 -

Table of Contents

1. Introduction ..................................................................................................................3

1.1. Minimum System Requirements .................................................................................... 3

2. Hardware Installation ...................................................................................................4

2.1. Hardware Installation ..................................................................................................... 4

2.1.1. AMD Crossﬁ re ..................................................................................................................5

3. Software Installation ....................................................................................................7

3.1. Driver and Utility Installation .......................................................................................... 7

3.1.1. Driver Installation ..............................................................................................................7

3.1.2. GIGABYTE OC Guru II .....................................................................................................9

3.2. Taskbar Icon ............................................................................................................ 19

3.3. Display Properties Pages ........................................................................................ 21

4. AMD Eyeﬁ nity ............................................................................................................36

5. Appendix ....................................................................................................................37

- 3 - Introduction

1. Introduction

1.1. Minimum System Requirements

• Hardware

- Intel®Pentium®4 / CoreTM 2 or AMD AthlonTM / PhenomTM

- 1 GB or more of system memory for best performance

- Optical drive for software installation (CD-ROM or DVD-ROM drive)

• Operating System

- Windows ® 8

- Windows ® 7

- Windows ®

Vista

- Windows®

XP with Service Pack 2 (SP2)

- Windows ®

XP Professional x64 Edition

- 4 -AMD Series Graphics Accelerator

2.2. Hardware Installation

Step 3.

Plug the display cable into your card; then turn on the computer and monitor. To connect a ﬂ at panel display

to your graphics card, use the DVI-I connector. To connect an HDMI monitor to your graphics card, use the

HDMI connector. To connect a DisplayPort monitor to your graphics card, use the DisplayPort connector.

Step 1.

Locate the PCI Express x16 slot. If necessary, remove the metal

cover from this slot; then align your graphics card with the PCI

Express x16 slot, and press it in firmly until the card is fully

seated.

Step 2.

Replace the screw to fasten the card in place, and replace the

computer cover.

Make sure that the gold edge connector of the graphics card is

securely inserted.

After installation, remember to connect the power cable to your graphics card, or the system

will not boot. Do not touch the card when it’s operating to prevent system instability.

You are now ready to proceed with the installation of the graphics card driver. Please refer to next chapter for

detailed instructions.

To Flat Panel Display To Flat Panel Display To HDMI Monitor

To D-sub Monitor

To Mini HDMI Monitor

To Mini DisplayPort Monitor To Mini DisplayPort Monitor

- 5 - Hardware Installation

2.1.1. How to enable the AMD CrossFireX

TM technology?

• CrossFireXTM Conﬁ guration

If you are planning on using this graphics card as part of a CrossFireX system, the following is required:

- A CrossFireX certiﬁ ed motherboard with two PCI Express x16 slots and correct chipset driver

- One or two CrossFire bridge interconnect cables

Two CrossFire bridge

interconnect cables.

Two CrossFire graphics cards of the same type.

(Example: GV-RX195P256D-RH)

Figure 1

Step 2:

After installing graphics card driver in operating system, when an AMD CrossFireX conﬁ guration is detected

for the ﬁ rst time by the AMD Catalyst display driver, AMD CrossFireX support is automatically enabled, and

the best possible GPU combination is selected based on the hardware conﬁ guration.

If AMD CrossFireX is not enabled, access the AMD Catalyst Control Center (please refer to Page 14). From

the AMD Catalyst Control Center, enter the CrossFire menu and assure to select the Enable CrossFireXTM

check box (Figure 2).

Figure 2

Step 1:

Install two CrossFireX graphics cards of the same chipset on a CrossFireX-supported motherboard and con-

nect the graphics cards via two CrossFire bridge interconnect cables (Figure 1). Then users can enable the

CrossFireX technology through the graphics card driver.

- 7 - Software Installation

3. Software Installation

Notice the following guidelines before installing the drivers:

1. First make sure your system has installed DirectX 9 or later version.

2. Make sure your system has installed the appropriate motherboard drivers

(for the motherboard drivers, please contact the motherboard manufacturer.)

Notice : The photos in this manual are for reference only and may not match what you exactly see on your screen

3.1. Driver and Utility Installation

3.1.1. Driver Installation

After installing the operating system, insert the driver disk into your optical drive. The driver Autorun screen

is automatically displayed which looks like that shown in the screen shot below. (If the driver Autorun screen

does not appear automatically, go to My Computer, double-click the optical drive and execute the setup.exe

program.)

For software MPEG support in Windows XP, you must install DirectX ﬁ rst. Users who run Windows

XP with Service Pack 2 or above do not need to install DirectX separately.

Step 1:

Click the item.Install Display Driver

Step 2:

Select the displayed language and then click .Next

Step 3:

Click the button.Install

- 8 -AMD Series Graphics Accelerator

Setp 4:

Click the or icon and then Express Custom

click .Next

Step 5:

Click the button.Accept

The system is installing the components. Step 6:

Click the button to restart the computer.Finish

Then the driver installation is completed.

- 9 - Software Installation

3.1.2. GIGABYTE OC Guru II

Step 1:

Click the item.GIGABYTE OC Guru II

Step 2:

Choose the language for the installation and click the button.OK

Step 3:

Choose the Typical and click the Next button

Step 4:

Click the Finish button. Then the installation of the

GIGABYTE OC Guru II is completed.

The system is installing the components.

- 10 -AMD Series Graphics Accelerator

OC GURU II: Proﬁ les

Users have 5 Proﬁ les, 1/ 2/ 3/ 4/ 5 , to set dierent proﬁ les.

By clicking 1/ 2/ 3/ 4/ 5, users can switch around these proﬁ les

This page indicates where users can set up MONITORING、GPU CLOCK、MEMORY CLOCK、FAN、

GPU VOLTAGE、MEMORY VOLTAGE、OSD、ONLINE SUPPORT.

Function: When it’s locked, GPU CLOCK / MEMORY CLOCK / GPU VOLTAGE /

MEMORY VOLTAGE can not be changed.

Function: When it’s unlocked, GPU CLOCK / MEMORY CLOCK / GPU VOLTAGE /

MEMORY VOLTAGE can be adjusted.

Function: Apply to what has just been setup.

Function: Return to the previous applied setup.

Function: Restore the default setup.

- 11 - Software Installation

MONITORING:

MONITORING PANEL:

Show real time GPU Clock/MEMORY Clock

Click MORE to MONITORING PANEL

Function: Monitoring Panel Settings.

Function: Start recording.

Function: Stop recording.

- 12 -AMD Series Graphics Accelerator

Monitoring panel settings:

Function: Set up a folder to save the recorded ﬁ les.

Function: Show the chosen items on the MONITORING PANEL.

Function: Return to MONITORING Page.

Function: Save the settings.

Function: Restore the default setup.

- 13 - Software Installation

GPU CLOCK:

MEMORY CLOCK:

When changing DEFAULT CLOCK, represents PLUS and represents MINUS.

Show GPU OFFSET, users can enter numbers directly to change GPU OFFSET.

MEMORY CLOCK is the combination of DEFAULT CLOCK and OFFSET.

When changing MEMORY CLOCK, represents PLUS and represents MINUS.

Show MEMORY OFFSET, users can enter numbers directly to change MEMORY OFFSET.

- 14 -AMD Series Graphics Accelerator

FAN

Show real time fan speed and fan mode

SETTINGS:

SPEED: show real time fan speed, it will show 0% if using a passive graphics card.

MODE: show Auto mode or Manual mode, users can set up in SETTINGS

AUTO mode, fans will be controlled automatically.

MANUAL mode, users can adjust fan behavior by adjusting the blue point on the fan graph.

Return to PROFILES page.

- 15 - Software Installation

GPU VOLTAGE

Users can enter numbers directly to change GPU VOLTAGE.

Show and set up GPU VOLTAGE

When changing GPU VOLTAGE, represents PLUS and represents MINUS.

MEMORY VOLTAGE

Show and set up MEMORY VOLTAGE

When changing MEMORY VOLTAGE, represents PLUS and represents MINUS.

Show OSD HOT KEY and OSD location

Click SETTINGS to OSD settings

Product specificaties

Merk:	Gigabyte
Categorie:	Videokaart
Model:	GV-R485MC-1GH
Vormfactor:	Full-Height/Full-Length (FH/FL)
Maximum resolutie:	2048 x 1536 Pixels
HDCP:	Ja
HDMI:	Ja
Geïntegreerde TV Tuner:	Nee
Mac-compatibiliteit:	Nee
Grafische geheugen:	1 GB
Soort aansluiting:	PCI Express 2.0
Minimale processor:	Pentium/Core 2, Athlon/Phenom
TV-uit:	Ja
Type koeling:	Passief
Minimale RAM:	1024 MB
Grafische adapter, soort geheugen:	GDDR3
Geheugenbus:	256 Bit
OpenGL versie:	2.1
DirectX versie:	10.1
Minimum system power voorraad:	450 W
Dual Link DVI:	Ja
Brackethoogte:	Full-Height (FH)