Generac QT13068ANANA Handleiding

Generac Generator QT13068ANANA

Lees hieronder de 📖 handleiding in het Nederlandse voor Generac QT13068ANANA (149 pagina's) in de categorie Generator. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/149

Standby Generator Sets

Table of Contents

SECTION PAGE

SAFETY RULES ................................................ 1-1

INTRODUCTION .....................................................1-3

Read this Manual Thoroughly ...................................1-3

Operation and Maintenance ......................................1-3

How to Obtain Service ..............................................1-3

IDENTIFICATION RECORD .....................................2-1

Data Label ................................................................2-1

EQUIPMENT DESCRIPTION ...................................3-1

Equipment Description ................................................3-1

Engine Oil Recommendations ......................................3-1

Coolant Recommendations...........................................3-1

ENGINE PROTECTIVE DEVICES ............................4-1

Coolant Temperature Sensing ...................................4-1

Low Coolant Level .....................................................4-1

Oil Pressure Sensing .................................................4-1

Overcrank Shutdown ................................................4-1

Overspeed Shutdown ................................................4-1

RPM Sensor Loss Shutdown .....................................4-1

DC Fuse ....................................................................4-1

FUEL SYSTEMS .....................................................5-1

Fuel Requirements ....................................................5-1

Natural Gas Fuel System ..........................................5-1

Propane Vapor Withdrawal Fuel System....................5-1

LP Fuel System .........................................................5-1

SPECIFICATIONS ...................................................6-1

Generator .................................................................6-1

Engine.......................................................................6-1

Cooling System .........................................................6-1

Fuel System ..............................................................6-1

Electrical System ......................................................6-1

5.4L & 6.8L Ignition Description .................................6-3

Ignition Power-up Input (“56 Line Input”) .................6-3

Ignition Enable (“14 Line Input”) ..............................6-3

Ignition Shutdown on Loss of Crank

or CAM Signals .........................................................6-3

Diagnostic Blink Patterns (Red LED Located

on the Ignition Control Board ...................................6-3

GENERAL INFORMATION .......................................7-1

Generator AC Lead Connections ..................................7-1

Alternator Power Winding Connections ........................7-1

Four-lead, Single-phase Stator ..................................7-1

3-phase Alternators ("Y" Configuration) ....................7-1

3-phase Alternators ("Delta" Configuration) ..............7-2

INSTALLATION .......................................................8-1

Installation ...................................................................8-1

Preparation Before Start-up .........................................8-1

Transfer Switch ........................................................8-1

Fuel System ..............................................................8-1

Generator Set Lubrication ........................................8-1

Prior to Initial Start-up .............................................8-1

Engine Coolant .........................................................8-1

Belt Tension ..............................................................8-1

Electrical System ......................................................8-1

Initial Inspection for QT Genset Start-up .....................8-1

Start-up Checklist ........................................................8-2

Preparation for Start-up............................................8-2

Start-up Inspection ...................................................8-2

OPERATION ...........................................................9-1

Generator Control and Operation ................................9-1

Operating Unit with Manual Transfer Switch ...............9-1

Engine Start-up and Transfer ...................................9-1

Retransfer and Shutdown .........................................9-1

Operating Unit with Automatic Transfer Switch ...........9-1

MAINTENANCE .....................................................10-1

Maintenance Performed by Authorized

Service Facilities .....................................................10-1

Every Three Months ...............................................10-1

Once Every Six Months ...........................................10-1

Once Annually .........................................................10-1

First 100 Operating Hours ......................................10-1

Every 500 Operating Hours ....................................10-1

Cooling System ..........................................................10-1

Checking Fluid Levels ................................................10-1

Check Engine Oil ....................................................10-1

Battery Fluid ...........................................................10-1

Engine Coolant .......................................................10-2

Maintenance Owner/Operator Can Perform ................10-2

Check Engine Oil Level ...........................................10-2

Check Battery .........................................................10-2

Exercise System ......................................................10-2

Inspect Cooling System ...........................................10-2

Check Engine Coolant Level....................................10-2

Perform Visual Inspection .......................................10-2

Inspect Exhaust System ..........................................10-2

Check Fan Belt ........................................................10-2

Inspect Engine Governor ........................................10-2

Changing Engine Oil ...............................................10-2

Changing the Engine Air Cleaner ............................10-3

Spark Plugs ............................................................10-3

Coolant Change .......................................................10-3

Miscellaneous Maintenance ........................................10-3

Cleaning the Generator ...........................................10-3

Battery ....................................................................10-4

Battery Maintenance ...............................................10-4

Battery Replacement ...............................................10-4

SERVICE SCHEDULE ...........................................11-1

30 kW - 150 kW Standby Gas Engine

Driven Generator Sets ............................................11-1

TROUBLESHOOTING ...........................................12-1

Troubleshooting Guide ...............................................12-1

NOTES

EXPLODED VIEWS & PARTS LISTS

WIRING DIAGRAMS & SCHEMATICS

WARRANTY

Content010 Rev. 0 04/06

1-1

INTRODUCTION

Thank you for purchasing this model of the Stationary

Emergency Generator set product line.

Every effort was expended to make sure that the

information and instructions in this manual were

both accurate and current at the time the manual was

written. However, the manufacturer reserves the right

to change, alter or otherwise improve this product(s)

at any time without prior notice.

READ THIS MANUAL THOROUGHLY 

If any portion of this manual is not understood, con-

tact the nearest Authorized Service Dealer for start-

ing, operating and servicing procedures.

Throughout this publication, and on tags and decals

affixed to the generator, DANGER, WARNING,

CAUTION and NOTE blocks are used to alert person-

nel to special instructions about a particular service

or operation that may be hazardous if performed

incorrectly or carelessly. Observe them carefully.

Their definitions are as follows:

DANGER

After this heading, read instructions that, if not

strictly complied with, will result in serious person-

al injury, including death, or property damage.

After this heading, read instructions that, if not

strictly complied with, may result in personal

injury or property damage.

After this heading, read instructions that, if not

strictly complied with, could result in damage to

equipment and/or property.

NOTE:

After this heading, read explanatory statements

that require special emphasis.

These safety warnings cannot eliminate the hazards

that they indicate. Common sense and strict compli-

ance with the special instructions while performing

the service are essential to preventing accidents.

Four commonly used safety symbols accompany the

DANGER, WARNING and CAUTION blocks. The type

of information each indicates is as follows:

 This symbol points out important safety infor-

mation that, if not followed, could endanger

personal safety and/or property of others.

 This symbol points out potential explosion

hazard.

 This symbol points out potential fire hazard.

 This symbol points out potential electrical shock

hazard.

The operator is responsible for proper and safe use

of the equipment. The manufacturer strongly recom-

mends that the operator read this Owner's Manual

and thoroughly understand all instructions before

using this equipment. The manufacturer also strong-

ly recommends instructing other users to properly

start and operate the unit. This prepares them if they

need to operate the equipment in an emergency.

OPERATION AND MAINTENANCE 

It is the operator's responsibility to perform all safety

checks, to make sure that all maintenance for safe

operation is performed promptly, and to have the

equipment checked periodically by an Authorized

Service Dealer. Normal maintenance service and

replacement of parts are the responsibility of the

owner/operator and, as such, are not considered

defects in materials or workmanship within the terms

of the warranty. Individual operating habits and usage

contribute to the need for maintenance service.

Proper maintenance and care of the generator ensure

a minimum number of problems and keep operating

expenses at a minimum. See an Authorized Service

Dealer for service aids and accessories.

Operating instructions presented in this manual

assume that the generator electric system has been

installed by an Authorized Service Dealer or other

competent, qualified contractor. Installation of this

equipment is not a “do-it-yourself” project.

HOW TO OBTAIN SERVICE 

When the generator requires servicing or repairs,

simply contact an Authorized Service Dealer for

assistance. Service technicians are factory-trained

and are capable of handling all service needs.

When contacting an Authorized Service Dealer or the

factory about parts and service, always supply the

complete model number of the unit as given on the

front cover of this manual or on the DATA LABEL

affixed to the unit.

AUTHORIZED SERVICE DEALER LOCATION

To locate the nearest AUTHORIZED

SERVICE DEALER, please call this number:

1-800-333-1322

or locate us on the web at:

www.generac.com

Stationary Emergency Generator

Important Safety Instructions

Safety 001 Rev. B 10/08

Study these SAFETY RULES carefully before install-

ing, operating or servicing this equipment. Become

familiar with this Owner’s Manual and with the unit.

The generator can operate safely, efficiently and reli-

ably only if it is properly installed, operated and

maintained. Many accidents are caused by failing to

follow simple and fundamental rules or precautions.

The manufacturer cannot anticipate every possible

circumstance that might involve a hazard. The warn-

ings in this manual, and on tags and decals affixed

to the unit are, therefore, not all inclusive. If a pro-

cedure, work method or operating technique is used

that the manufacturer does not specifically recom-

mend, ensure that it is safe for others. Also make

sure the procedure, work method or operating tech-

nique utilized does not render the generator unsafe.

DANGER

 Despite the safe design of this generator,

operating this equipment imprudently, neglect-

ing its maintenance or being careless can cause

possible injury or death. Permit only responsible

and capable persons to install, operate or main-

tain this equipment.

 Potentially lethal voltages are generated by

these machines. Ensure all steps are taken to

render the machine safe before attempting to

work on the generator.

 Parts of the generator are rotating and/or hot

during operation. Exercise care near running

generators.

 GENERAL HAZARDS 

• For safety reasons, the manufacturer recommends

that this equipment be installed, serviced and

repaired by an Authorized Service Dealer or other

competent, qualified electrician or installation tech-

nician who is familiar with applicable codes, stan-

dards and regulations. The operator also must

comply with all such codes, standards and regula-

tions.

• Installation, operation, servicing and repair of this

(and related) equipment must always comply with

applicable codes, standards, laws and regulations.

Adhere strictly to local, state and national electri-

cal and building codes. Comply with regulations

the Occupational Safety and Health Administration

(OSHA) has established. Also, ensure that the

generator is installed, operated and serviced in

accordance with the manufacturer’s instructions

and recommendations. Following installation, do

nothing that might render the unit unsafe or in

noncompliance with the aforementioned codes,

standards, laws and regulations.

• The engine exhaust fumes contain carbon mon-

oxide gas, which can be DEADLY. This dangerous

gas, if breathed in sufficient concentrations, can

cause unconsciousness or even death. For that

reason, adequate ventilation must be provided.

This should be considered prior to installing the

generator. The unit should be positioned to direct

exhaust gasses safely away from any building

where people, animals, etc., will not be harmed.

Any exhaust stacks that ship loose with the unit

must be installed properly per the manufacturer's

instruction, and in strict compliance with appli-

cable codes and standards.

• Keep hands, feet, clothing, etc., away from drive

belts, fans, and other moving or hot parts. Never

remove any drive belt or fan guard while the unit

is operating.

• Adequate, unobstructed flow of cooling and venti-

lating air is critical in any room or building hous-

ing the generator to prevent buildup of explosive

gases and to ensure correct generator operation.

Do not alter the installation or permit even partial

blockage of ventilation provisions, as this can seri-

ously affect safe operation of the generator.

• Keep the area around the generator clean and

uncluttered. Remove any materials that could

become hazardous.

• When working on this equipment, remain alert

at all times. Never work on the equipment when

physically or mentally fatigued.

• Inspect the generator regularly, and promptly

repair or replace all worn, damaged or defective

parts using only factory-approved parts.

 SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe

operation be copied and posted in potential hazard areas. Safety should be stressed to all

operators, potential operators, and service and repair technicians for this equipment.

The engine exhaust from this product

contains chemicals known to the state

of California to cause cancer, birth

defects or other reproductive harm.

WARNING:

 

This product contains or emits chemicals

known to the state of California to cause

cancer, birth defects or other reproductive harm.

WARNING:

 

1-2

Stationary Emergency Generator

Important Safety Instructions



Safety 001 Rev. B 10/08

Product specificaties

Merk:	Generac
Categorie:	Generator
Model:	QT13068ANANA

Heb je hulp nodig?

Als je hulp nodig hebt met Generac QT13068ANANA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Generator Generac

Generac G0076760 Handleiding

27 Augustus 2024

Generac G0072101 Handleiding

27 Augustus 2024

Generac G0072240 Handleiding

26 Augustus 2024

Generac G0076830 Handleiding

26 Augustus 2024

Generac RA01522L Handleiding

26 Augustus 2024

Generac G0076730 Handleiding

26 Augustus 2024

Generac G0080250 Handleiding

26 Augustus 2024

Generac RA02022L Handleiding

26 Augustus 2024

Generac RG06045C Handleiding

26 Augustus 2024

Generac G0072280 Handleiding

26 Augustus 2024

Handleiding Generator

Nieuwste handleidingen voor Generator

Jackery SolarSaga 80 Handleiding

8 December 2024

Westinghouse WGen7500s Handleiding

8 December 2024

Bavaria BPG 2500 Handleiding

5 December 2024

Einhell KCST 1000 D Handleiding

4 December 2024

Einhell NPG 850 Handleiding

4 December 2024

Einhell RT-PG 5500/1 D Handleiding

4 December 2024

Einhell RT-PG 850 Handleiding

4 December 2024

Einhell BT-PG 850/1 Handleiding

4 December 2024

Einhell BT-PG 850/2 Handleiding

4 December 2024

Einhell BT-PG 3600 R Handleiding

4 December 2024