Generac QT04524AVSN Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Generac QT04524AVSN (107 pagina's) in de categorie Generator. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/107
STANDBY GENERATOR
OWNER'S MANUAL
This manual should remain with the unit.
A new standard of reliability
Serial Number QT
2.4L
45kW
Models
Cover054 Rev. 0 04/06 Part No. 0G1157
Standby Generator Sets
Table of Contents
SECTION PAGE
SAFETY RULES ................................................ 1-1
INTRODUCTION .....................................................1-3
Read this Manual Thoroughly ...................................1-3
Operation and Maintenance ......................................1-3
How to Obtain Service ..............................................1-3
IDENTIFICATION RECORD .....................................2-1
Data Label ................................................................2-1
EQUIPMENT DESCRIPTION ...................................3-1
Equipment Description ................................................3-1
Engine Oil Recommendations ......................................3-1
Coolant Recommendations...........................................3-1
ENGINE PROTECTIVE DEVICES ............................4-1
High Coolant Temperature Switch ............................4-1
Low Coolant Level Sensor .........................................4-1
Low Oil Pressure Switch ...........................................4-1
Overcrank Shutdown ................................................4-1
Overspeed Shutdown ................................................4-1
RPM Sensor Loss Shutdown .....................................4-1
DC Fuse ....................................................................4-1
FUEL SYSTEMS .....................................................5-1
Fuel Requirements ....................................................5-1
Natural Gas Fuel System ..........................................5-1
Propane Vapor Withdrawal Fuel System....................5-1
LP Fuel System .........................................................5-1
SPECIFICATIONS ...................................................6-1
Generator .................................................................6-1
Engine.......................................................................6-1
Cooling System .........................................................6-1
Fuel System ..............................................................6-1
Electrical System ......................................................6-1
Cold Weather Kit .......................................................6-2
Reconfiguring the Fuel System ..................................6-2
GENERAL INFORMATION .......................................7-1
Generator AC Lead Connections ..................................7-1
Four-lead, Single-phase Stator ..................................7-1
Alternator Power Winding Connections ........................7-1
3-phase Alternators ..................................................7-1
INSTALLATION .......................................................8-1
Installation ...................................................................8-1
Preparation Before Start-up .........................................8-1
Transfer Switch ........................................................8-1
Fuel System ..............................................................8-1
Generator Set Lubrication ........................................8-1
Prior to Initial Start-up .............................................8-1
Engine Coolant .........................................................8-1
Belt Tension ..............................................................8-1
Electrical System ......................................................8-1
Initial Inspection for QT Genset Start-up .....................8-1
Start-up Checklist ........................................................8-2
Preparation for Start-up............................................8-2
Start-up Inspection ...................................................8-2
OPERATION ...........................................................9-1
Generator Control and Operation ................................9-1
Operating Unit with Manual Transfer Switch ...............9-1
Engine Start-up and Transfer ...................................9-1
Retransfer and Shutdown .........................................9-1
Operating Unit with Automatic Transfer Switch ...........9-1
MAINTENANCE .....................................................10-1
Maintenance Performed by Authorized
Service Facilities .....................................................10-1
Every Three Months ...............................................10-1
Once Every Six Months ...........................................10-1
Once Annually .........................................................10-1
First 100 Operating Hours ......................................10-1
Every 500 Operating Hours ....................................10-1
Every 800 Operating Hours ....................................10-1
Exhaust Manifold Procedure ......................................10-1
Intake Manifold Procedure .........................................10-1
Cylinder Head Procedure ...........................................10-1
Cooling System ..........................................................10-2
Overload Protection for Engine DC
Electrical System ....................................................10-2
Checking Fluid Levels ................................................10-2
Check Engine Oil ....................................................10-2
Battery Fluid ...........................................................10-2
Engine Coolant .......................................................10-2
Maintenance Owner/Operator Can Perform ................10-3
Check Engine Oil Level ...........................................10-3
Check Battery .........................................................10-3
Exercise System ......................................................10-3
Inspect Cooling System ...........................................10-3
Check Engine Coolant Level....................................10-3
Perform Visual Inspection .......................................10-3
Inspect Exhaust System ..........................................10-3
Check Fan Belt ........................................................10-3
Inspect Engine Governor ........................................10-3
Changing Engine Oil ...............................................10-3
Changing the Engine Air Cleaner ............................10-3
Spark Plugs ............................................................10-4
Coolant Change .......................................................10-4
Miscellaneous Maintenance ........................................10-4
Cleaning the Generator ...........................................10-4
Battery ....................................................................10-4
Battery Maintenance ...............................................10-4
Battery Replacement ...............................................10-5
SERVICE SCHEDULE ...........................................11-1
TROUBLESHOOTING ...........................................12-1
Troubleshooting Guide ...............................................12-1
NOTES
EXPLODED VIEWS & PARTS LISTS
WIRING DIAGRAMS & SCHEMATICS
WARRANTY
Content004 Rev. 0 09/05
1-1
INTRODUCTION
Thank you for purchasing this model of the Stationary Emergency
Generator set product line.
Every effort was expended to make sure that the information and
instructions in this manual were both accurate and current at the
time the manual was written. However, the manufacturer reserves
the right to change, alter or otherwise improve this product(s) at
any time without prior notice.
READ THIS MANUAL THOROUGHLY
If any portion of this manual is not understood, contact the near-
est Authorized Service Dealer for starting, operating and servicing
procedures.
Throughout this publication, and on tags and decals affixed to the
generator, DANGER, WARNING, CAUTION and NOTE blocks are
used to alert personnel to special instructions about a particular
service or operation that may be hazardous if performed incor-
rectly or carelessly. Observe them carefully. Their definitions are
as follows:
INDICATES A HAZARDOUS SITUATION OR
ACTION WHICH, IF NOT AVOIDED, WILL RESULT
IN DEATH OR SERIOUS INJURY.
Indicates a hazardous situation or action which,
if not avoided, could result in death or serious
injury.
Indicates a hazardous situation or action which,
if not avoided, could result in minor or moderate
injury.
NOTE:
Notes contain additional information important to a procedure
and will be found within the regular text body of this manual.
These safety warnings cannot eliminate the hazards that they
indicate. Common sense and strict compliance with the special
instructions while performing the action or service are essential to
preventing accidents.
Four commonly used safety symbols accompany the DANGER,
WARNING CAUTION and blocks. The type of information each
indicates is as follows:
n
This symbol points out important safety
information that, if not followed, could
endanger personal safety and/or property of
others.
This symbol points out potential explosion
hazard.
This symbol points out potential fire hazard.
This symbol points out potential electrical
shock hazard.
The operator is responsible for proper and safe use of the equip-
ment. The manufacturer strongly recommends that the operator
read this Owner's Manual and thoroughly understand all instruc-
tions before using this equipment. The manufacturer also strongly
recommends instructing other users to properly start and operate
the unit. This prepares them if they need to operate the equipment
in an emergency.
OPERATION AND MAINTENANCE
It is the operator's responsibility to perform all safety checks, to
make sure that all maintenance for safe operation is performed
promptly, and to have the equipment checked periodically by
an Authorized Service Dealer. Normal maintenance service and
replacement of parts are the responsibility of the owner/operator
and, as such, are not considered defects in materials or workman-
ship within the terms of the warranty. Individual operating habits
and usage contribute to the need for maintenance service.
Proper maintenance and care of the generator ensure a minimum
number of problems and keep operating expenses at a minimum.
See an Authorized Service Dealer for service aids and accessories.
Operating instructions presented in this manual assume that the
generator electric system has been installed by an Authorized
Service Dealer or other competent, qualified contractor. Installation
of this equipment is not a “do-it-yourself” project.
HOW TO OBTAIN SERVICE
When the generator requires servicing or repairs, simply contact
an Authorized Service Dealer for assistance. Service technicians
are factory-trained and are capable of handling all service needs.
When contacting a dealer about parts and service, always supply
the complete Model Number, Serial Number and Type Code (where
applicable) from the DATA LABEL that is affixed to the unit.
AUTHORIZED SERVICE DEALER LOCATION
To locate the nearest AUTHORIZED
SERVICE DEALER, please call this number:
1-800-333-1322
or locate us on the web at:
www.generac.com
Safety 001 Rev. d 06/10
Safety Rules
Product specificaties
| Merk: | Generac |
| Categorie: | Generator |
| Model: | QT04524AVSN |
Heb je hulp nodig?
Als je hulp nodig hebt met Generac QT04524AVSN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Generator Generac
27 Augustus 2024
27 Augustus 2024
26 Augustus 2024
26 Augustus 2024
26 Augustus 2024
26 Augustus 2024
26 Augustus 2024
26 Augustus 2024
26 Augustus 2024
26 Augustus 2024
Handleiding Generator
- Generator Braun
- Generator Bosch
- Generator Philips
- Generator DeWalt
- Generator Honeywell
- Generator Yamaha
- Generator Al-ko
- Generator Anker
- Generator Bavaria
- Generator Black Decker
- Generator Defort
- Generator Dometic
- Generator Domo
- Generator Duro Pro
- Generator Duromax
- Generator Einhell
- Generator EizenKraft
- Generator Eurom
- Generator Ferm
- Generator Ferrex
- Generator Fuxtec
- Generator Global
- Generator Gude
- Generator Gys
- Generator Harvia
- Generator Hitachi
- Generator Homelite
- Generator Honda
- Generator Husqvarna
- Generator Hyundai
- Generator Innoliving
- Generator ITC Power
- Generator Kinzo
- Generator Kraftech
- Generator Load Up
- Generator Lumag
- Generator Makita
- Generator Moulinex
- Generator Parkside
- Generator Powerfix
- Generator Powerkick
- Generator Powerplus
- Generator PowerTech
- Generator Primo
- Generator Robin America
- Generator Rowenta
- Generator Scheppach
- Generator Stanley
- Generator Stromkraft
- Generator Subaru
- Generator Sunbird Solar
- Generator Superior
- Generator Swiss Kraft
- Generator Taurus
- Generator Telair
- Generator Toolcraft
- Generator Trotec
- Generator Vetus
- Generator Voltcraft
- Generator Westinghouse
- Generator Woods
- Generator Workzone
- Generator Zgonc
- Generator Zipper
- Generator JL Audio
- Generator Joy-it
- Generator Ozito
- Generator Black And Decker
- Generator Cocraft
- Generator Draper
- Generator Simpson
- Generator Truper
- Generator Sun Joe
- Generator Herkules
- Generator Könner & Söhnen
- Generator Zephyr
- Generator MSW
- Generator Craftsman
- Generator Cecotec
- Generator CAT
- Generator Cleanmaxx
- Generator Alpha Tools
- Generator Full Boar
- Generator Powerhouse
- Generator ART
- Generator GW Instek
- Generator Endress
- Generator AudioControl
- Generator EcoFlow
- Generator Powerspot
- Generator King Craft
- Generator Cummins
- Generator Briggs & Stratton
- Generator SRS
- Generator Bluetti
- Generator Anova
- Generator Blodgett
- Generator CrossTools
- Generator Jackery
- Generator Rigol
- Generator Aim TTi
- Generator Lifan
- Generator Cleveland
- Generator Solaaron
- Generator A-iPower
- Generator Prowork
- Generator Ribimex
- Generator Arvey
- Generator Tektronix
- Generator PRAMAC
- Generator DuroStar
- Generator ThermaSol
Nieuwste handleidingen voor Generator
19 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
17 November 2024
16 November 2024
16 November 2024
15 November 2024