Generac QT03015GNSX Handleiding

Generac Generator QT03015GNSX

Lees hieronder de 📖 handleiding in het Nederlandse voor Generac QT03015GNSX (78 pagina's) in de categorie Generator. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/78
Cover204 Rev. A 11/11 Part No. 0J6142
n
1-1
n
n
Despite the safe design of this generator,
operating this equipment imprudently, neglect-
ing its maintenance or being careless can cause
possible injury or death. Permit only respon-
sible and capable persons to install, operate or
maintain this equipment.
Potentially lethal voltages are generated by
these machines. Ensure all steps are taken to
render the machine safe before attempting to
work on the generator.
n
Parts of the generator are rotating and/or hot
during operation. Exercise care near running
generators.
1-2
1-3
IDENTIFICATION RECORD
2-1
General Information
Any attempt to crank or start the engine before
it has been properly serviced with the recom-
mended oil may result in an engine failure.
Do not use any chromate base rust inhibitor
with ethylene glycol base anti-freeze or chro-
mium hydroxide (“green slime”) forms and will
cause overheating. Engines that have been
operated with a chromate base rust inhibitor
must be chemically cleaned before adding eth-
ylene glycol base anti-freeze. Using any high
silicate anti-freeze boosters or additives will
also cause overheating. The manufacturer also
recommends that any soluble oil inhibitor is
NOT used for this equipment.
Do not remove the radiator pressure cap while
the engine is hot or serious burns from boiling
liquid or steam could result.
Ethylene glycol base antifreeze is poisonous.
Do not use mouth to siphon coolant from the
radiator, recovery bottle or any container. Wash
hands thoroughly after handling. Never store
used antifreeze in an open container because
animals are attracted to the smell and taste of
antifreeze even though it is poisonous to them.
3-1
Equip007 Rev. D 07/11
ENGINE PROTECTIVE DEVICES
HIGH COOLANT TEMPERATURE SENDER
LOW COOLANT LEVEL SENSOR
LOW OIL PRESSURE SWITCH
OVERCRANK SHUTDOWN
OVERSPEED SHUTDOWN
RPM SENSOR LOSS SHUTDOWN
DC FUSES
4-1
Engine Protective Devices
FUEL SYSTEM
FUEL REQUIREMENTS
The Stationary Emergency Generator may be equipped with one of
the following fuel systems:
• Natural gas fuel system
• Propane vapor (LPV) fuel system
Recommended fuels should have a Btu content of at least 1,000
Btu's per cubic foot for natural gas; or at least 2,520 Btu's per
cubic foot for LP gas. Ask the fuel supplier for the Btu content of
the fuel.
NOTE:
The fuel consumption requirements are identified in the
Specifications section of the Owner's Manual. Refer to the
Installation Manual if assistance is required for the sizing of
the pipe diameter for the generator. Any piping used to connect
the generator to the fuel supply should be of adequate size to
achieve the 100% load fuel consumption requirements identi-
fied in the Specifications section regardless of actual load.
NOTE:
The recommended fuel pressure is identified in the Specifications
section this manual.
NOTE:
It is the responsibility of the installer to make sure that only
the correct recommended fuel is supplied to the generator fuel
system. Thereafter, the owner/operator must make certain that
only the proper fuel is supplied.
NATURAL GAS FUEL SYSTEM
Natural gas is supplied in its vapor state. In most cases, the gas
distribution company provides piping from the main gas distribu-
tion line to the standby generator site. The following information
applies to natural gas fuel systems.
• Gas pressure in a building is usually regulated by national, state
and local codes.
• To reduce gas pressure to a safe level before the gas enters a
building, a primary regulator is needed. The natural gas supplier
may or may not supply such a regulator.
• It is the responsibility of the gas supplier to make sure sufficient
gas pressure is available to operate the primary regulator.
• Gas pressure at the inlet to the fuel shutoff solenoid must never
exceed approximately 14 inches water column (0.5 psi).
PROPANE VAPOR WITHDRAWAL FUEL SYSTEM
This type of system utilizes the vapors formed above the liquid
fuel in the supply tank. Approximately 10 to 20 percent of the tank
capacity is needed for fuel expansion from the liquid to the vapor
state. The vapor withdrawal system is generally best suited for
smaller engines that require less fuel. The installer should be aware
of the following:
• When ambient temperatures are low and engine fuel consump-
tion is high, the vapor withdrawal system may not function
efficiently.
• Ambient temperatures around the supply tank must be high
enough to sustain adequate vaporization, or the system will not
deliver the needed fuel volume.
• In addition to the cooling effects of ambient air, the vaporization
process itself provides an additional cooling effect.
5-1
FuelSys001 Rev. F 04/11
Fuel System
SPECIFICATIONS
Type......................................................................Synchronous
Rotor Insulation Class H .............................................................
Stator Insulation Class H ............................................................
Alternator Output Leads 3-phase ..................................... 6-wire
Bearings .................................................................. Sealed Ball
Coupling ................................................................Flexible Disc
Load Capacity (Standby Rating) 25/30 kW* ...............................
* NOTE: Generator rating and performance in accordance with ISO8528-5, BS5514, SAE
J1349, ISO3046 and DIN 6271 Standards. kW rating is based on LPG fuel and may derate
with natural gas.
Excitation System ............................................................Direct
Generator Output Voltage/kW - 60 Hz
kW Amp CB Size
120/240 V, 1-phase, 1.0 pf 25/30 104/125 125/150
120/208 V, 3-phase, 0.8 pf 25/30 87/104 100/125
120/240 V, 3-phase, 0.8 pf 25/30 75/90 90/100
Generator Locked Rotor kVA Available @ Voltage Dip of 35%
25 kW 30 kW
35 kVA 45 kVA
Make Generac ...........................................................................
Model .............................................................................In Line
Cylinders and Arrangement .....................................................4
Displacement ............................................................... 1.5 Liter
Bore............................................................ 77.4 mm (3.05 in.)
Stroke ......................................................... 79.5 mm (3.13 in.)
Compression Ratio........................................................ 11-to-1
Air Intake System Naturally Aspirated .........................................
Spark Plug Gap 0.9 mm (0.035 inch) .........................................
Engine Parameters
Rated Synchronous RPM 60 Hz, 3600 .......................................
Exhaust System
Exhaust Flow at Rated Output 60 Hz (25/30 kW) 203/237 cfm ...
Exhaust Temp. at Rated Output (25/30 kW) 1100/1130 °F ..........
Combustion Air Requirements (Natural Gas)
Flow at rated power, 60 Hz (25/30 kW) 62/72 cfm .....................
Governor
Type...........................................................................Electronic
Frequency Regulation ............................................. Isochronous
Steady State Regulation ± .25% ................................................
Engine Lubrication System
Type of Oil Pump ...............................................................Gear
Oil Filter Full Flow, Cartridge .......................................................
Crankcase Oil Capacity 4 U.S. qts. ............................................
Type............................................................................... Closed
Water Pump Belt Driven .............................................................
Fan Speed ......................................................................... 2484
Fan Diameter 17.7 inches ...........................................................
Fan Mode ....................................................................... Pusher
Air Flow (inlet air including alternator and
combustion air) 2490 ft .................................................. 3/min.
Coolant Capacity 2.0 U.S. gal. ....................................................
Heat Rejection to Coolant (25/35 kW) 112,000/135,000 Btu/h ...
Maximum Operating Air Temp. on Radiator 60 °C (150 °F) .........
Maximum Ambient Temperature 50 °C (140 °F) .........................
Type of Fuel Natural Gas, Propane Vapor ....................................
Carburetor............................................................... Down Draft
Secondary Fuel Regulator............................................ Standard
Fuel Shut-off Solenoid ................................................. Standard
Operating Fuel Pressure 5 in. - 14 in. Water Column .................
Fuel Consumption - ft 3/hr (Natural Gas/LPV)
Exercise 25% 50% 75% 100%
Cycle Load Load Load Load
25 kW 60/24 220/88 297/119 362/145 430/172
30 kW 60/24 240/96 320/128 400/160 492/197
Battery Charge Alternator 12 V, 15 Amp .....................................
Smart Charger 2.0 Amp .............................................................
Recommended Battery Group 26, 525CCA .................................
System Voltage 12 Volts ............................................................
Voltage Regulator
Type...........................................................................Electronic
Regulation ........................................................................± 1%
Power Adjustment for Ambient Conditions
Temperature Deration:
3% for every 10° C above °C ..............................................25
1.65% for every 10° above °F .............................................77
Altitude Deration:
1% for every 100 m above m............................................183
3% for every 1000 ft. above ft. .........................................600
Controller Nexus .................................................................
6-1
GenSpec095 Rev. B 12/13
Specifications
6-2
ALTERNATOR AC LEAD
CONNECTIONS
ALTERNATOR POWER WINDING
CONNECTIONS
E1
S1
S6
S5
S4
S2
E2
S3
E3 L - N
L - L
INTERNAL
CONNECTIONS
00 (NEUTRAL)
E1
S1
S4
S7
S12
S11
S10
S8
S5
S2
E2
S9
S6
S3
E3 L - N
L - L
7-1
General Information
E3 E2
00 (NEUTRAL)
INTERNAL CONNECTIONS E1
L-L
L-N
S1 S1
S4 S4
S6
S6
S3
S3
S5
S5 S2
S2
E3 E2
E1
L-L
L-N
S7 S1
S10 S4
S12
S6
S9
S3
S5
S11 S2
S8
E1
S1
S6
S5
S4
S2
E2
S3
E3 L - N
L - L
INTERNAL
CONNECTIONS
00 (NEUTRAL)
E2
0VAC
2VAC
208C
240C
240 VAC
120 VAC 120 VAC
240 VAC
240 VAC
S2 S12
S11
S1
NB
S10
S3
E1 E3
E2
S5
S8
S9
S6
208 VAC
7-2
General Information
8-1
8-2
8-3
8-4
8-5
8-6
8-7
ACTIVATION
RUN LOGALARM LOG
HISTORY STATUS
COMMANDSTATE VERSIONSDISPLAY
GENERATOR
FREQUENCY
ENGINE
HOURS
ENGINE
RPM
BATTERY
VOLTAGE
DEBUG
INPUTS OUTPUTS DISPLAYS
EDIT
LANGUAGE
TIME/DATE
EXERCISE
TIME/SPEED
ESC Press the “ESCAPE key
to jump back up through
the menu levels.
+ / - Use the “+/-” key
to navigate through
the menu.
ENTER Use the “ENTER” key
to select items or
enter data.
ESC
ESC
ESC
ESC
ESC ESC
RESET
MAINTENANCE
QT TEST
MAIN MENU
n
The Maintenance Disconnect Switch and the
AUTO/OFF/MANUAL switches (if so equipped)
must be set properly, or the generator will
crank and start as soon as the utility power to
the transfer switch is turned off. Refer to appli-
cable control panel and transfer switch manuals
for more information.
n
Do not proceed until certain that utility source
voltage is available to the transfer switch and
the transfer switch main contacts are set to
UTILITY.
Do not attempt manual operation until all
power supplies to the transfer switch have been
positively turned off, or extremely dangerous -
possibly lethal - electrical shock will result.
Transfer switch enclosure doors should be kept
closed and locked. Only authorized personnel
should be allowed access to the transfer switch
interior. Extremely high and dangerous voltages
are present in the transfer switch.
nDo not crank the engine continuously for lon-
ger than 30 seconds, or the heat may
damage the starter motor.
9-1
1-G
Before working on the Stationary Emergency
Generator, ensure the following:
OIL FILTER
OIL DIP
STICK
OIL FILL CAP
AIR FILTER
Hot oil may cause burns. Allow engine to cool
before draining oil. Avoid prolonged or repeat-
ed skin exposure with used oil. Thoroughly
wash exposed areas with soap.
After refilling the crankcase with oil, always
check oil level on dipstick. NEVER OPERATE
ENGINE WITH OIL BELOW THE DIPSTICK “ADD”
MARK.
The exhaust system parts from this product get
extremely hot and remains hot after shutdown.
High grass, weeds, brush, leaves, etc. must
remain clear of the exhaust. Such materials may
ignite and burn from the heat of the exhaust
system.
10-1
If a circuit breaker opens or a fuse element
melts, find the cause of the overload before
resetting the circuit breaker or replacing the
fuse.
Do not attempt to adjust the governor. Only
qualified service facilities should adjust the
governor. Excessively high operating speeds
are dangerous and increase the risk of personal
injury. Low speeds impose a heavy load on the
engine when adequate engine power is not
available and may shorten engine life. Correct
rated frequency and voltage are supplied only
at the proper governed speed. Some connected
electrical load devices may be damaged by
incorrect frequency and/or voltage. Only quali-
fied service technicians should adjust the gov-
erned speed.
10-2
OIL FILL CAP
AIR FILTER
Storage batteries give off explosive hydrogen
gas. This gas can form an explosive mixture
around the battery for several hours after
charging. The slightest spark can ignite the gas
and cause an explosion. Such an explosion can
shatter the battery and cause blindness or other
injury. Any area that houses a storage battery
must be properly ventilated. Do not allow smok-
ing, open flame, sparks or any spark producing
tools or equipment near the battery.
Battery electrolyte fluid is an extremely corro-
sive sulfuric acid solution that can cause severe
burns. Do not permit fluid to contact eyes, skin,
clothing, painted surfaces, etc. Wear protective
goggles, protective clothing and gloves when
handling a battery. If fluid is spilled, flush the
affected area immediately with clear water.
Do not use any jumper cables or booster bat-
tery to crank and start the generator engine. If
the battery has completely discharged, remove
it from the generator for recharging.
Be sure the AUTO/OFF/MANUAL switch is set
to the OFF position, before connecting the
battery cables. If the switch is set to AUTO or
MANUAL, the generator can crank and start as
soon as the battery cables are connected.
Be sure the 120VAC power supply to the battery
is turned OFF, or sparking may occur at the bat-
tery posts as the cables are attached and cause
an explosion.
10-3
11-1
12-1
United States Environmental Protection Agency Warranty Statement
(Stationary Emergency Spark-Ignited Generators)
Warranty Rights, Obligations and Coverage
The United States Environmental Protection Agency (EPA) and Generac Power Systems, Inc. (Generac) are pleased to explain the Emission
Control System Warranty on your new stationary emergency engine. If during the warranty period, any emission control system or compo-
nent on your engine is found defective in materials or workmanship, Generac will repair your engine at no cost to you for diagnosis, replace-
ment parts and labor provided it be done by a Generac Authorized Warranty Service Facility. Your emission control system may include parts
such as the fuel metering, ignition, and exhaust systems and other related emission related components listed below. Generac will warrant
the emissions control systems on your 2009 and later model year engines provided there has been no abuse, neglect, unapproved modifica-
tion, or improper maintenance of your engine. For engines less than 130 HP the warranty period is two years from the date of sale to the ulti-
mate purchaser. For engines greater than or equal to 130 HP the warranty period is three years or 2500 hours of operation, whichever
comes first, from the date of the engine being placed into service. For high-cost warranted components, the Emission Control System war-
ranty is valid for 5 years or 3500 hours of operation, whichever comes first.
Purchaser's/Owner's Warranty Responsibilities
As the engine purchaser/owner you are responsible for the following: 1) The engine must be installed and configured in accordance to Gen-
erac's installation specifications. 2) The completion of all maintenance requirements listed in your Owner's Manual. 3) Any engine setting
adjustment must be done in accordance and consistent with the instructions in the Owner's Manual. 4) Any emission control system or com-
ponent must be maintained and operated appropriately in order to ensure proper operation of the engine and control system to minimize
emissions at all times.
Generac may deny any/or all Emission Control System Warranty coverage or responsibility of the engine, or an emission control system or
component on your engine thereof, if it has failed due to abuse, neglect, unapproved modification or improper maintenance, or the use of
counterfeit and/or “gray market” parts not made, supplied or approved by Generac. Warranty service can be arranged by contacting either
your selling dealer or a Generac Authorized Warranty Service dealer, 1-800-333-1322 for the dealer nearest you. The purchaser/owner shall
be responsible for any expenses or other charges incurred for service calls and/or tr spection or ansportation of the product to/from the in
repair facilities. The purchaser/owner shall be responsible for any and/or all damages or losses incurred while the engine is being trans-
ported/shipped for inspection or warranty repairs. Contact Generac Power Systems Inc. for additional Emission Control System Warranty
related information, Generac Power Systems, Inc., PO. Box 8, Waukesha, WI 53187, or call 1-800-333-1322 or www.generac.com.
Important Note
This warranty statement explains your rights and obligations under the Emission Control System Warranty, which is provided to you by Gen-
erac pursuant to federal law. Note that this warranty shall not apply to any incidental, consequential, or indirect damages caused by defects
in materials or workmanship or any delay in repair or replacement of the defective part(s). This warranty is in place of all other warranties,
expressed or implied. Specifically, Generac makes no other warranties as to the merchantability or fitness for a particular purpose. Any
implied warranties which are allowed by law, shall be limited in duration to the terms of the express warranty provided herein. Some states
do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Emission Related Parts Include the Following (if so equipped)
*High-Cost Warranted Component
EmsnWrnty001 Revision F (04/15)
1) Fuel Metering System
1.1) Gasoline Carburetor Assembly and Internal Components
A) Fuel Filter, B) Carburetor, C) Fuel Pump
1.2) Carburetion Assembly and Its Components
A) Fuel Controller, B) Carburetor and Its Gaskets,
C) Mixer and Its Gaskets, D) Primary Gas Regulator,
E) Liquid Vaporizer
1.3) Fuel Regulator
2) Air Induction System Including A) Intake Pipe/Manifold,
B) Air Cleaner
3) Ignition System Including A) Spark Plug, B) Ignition Module,
C) Ignition Coil, D) Spark Plug Wires
4) Exhaust System
A) Catalyst Assembly*, B) Exhaust Manifold, C) Muffler,
D) Exhaust Pipe, E) Muffler Gasket
5) Crankcase Breather Assembly Including
A) Breather Connection Tube, B) PCV Valve
6) Oxygen Sensor
7) Diagnostic Emission-Control System
United States Environmental Protection Agency Compliance Requirements
(Stationary Emergency Spark-Ignited Generators)
Purchaser's/Owner's Record Keeping Responsibilities
The United States Environmental Protection Agency (EPA) and Generac Power Systems, Inc. (Generac) are pleased to explain your record
keeping requirements for compliance with Subpart JJJJ- Standards of Performance for Stationary Spark Ignition Internal Combustion
Engines as listed in the Electronic Code of Federal Regulations Title 40 Part 60. As the engine purchaser/owner who operates and maintains
their certified emergency stationary engine and emission control system according to applicable emission related guidelines as specified in
this Owner's Manual, you are required to meet the following notification and record keeping requirements to demonstrate compliance: 1)
Maintain documentation that the engine is certified to meet emission standards. 2) Record keeping of maintenance conducted. 3) Record
keeping of the provision allowing natural gas engines to operate using propane for a maximum of 100 hours per year as an alternate fuel
solely during emergency operations provided the engine is not certified to operate on propane. 4) Meet all compliance notifications submitted
to the purchaser/owner and maintain all supporting documentation. 5) Record keeping of hours of operation, including what classified the
operation as emergency and how many hours are spent for non-emergency operation. For emergency engines greater than or equal to 130
HP, record keeping of hours of operation begins January 1, 2011. For emergency engines less than 130 HP, record keeping of hours of oper-
ation begins January 1, 2009; engines are equipped with non-resettable hour meters to facilitate record keeping.
Specific Air Quality Management or Air Pollution Control Districts may have different and additional record keeping/reporting requirements.
Your permit to construct and/or operate the engine may be contingent upon compliance with those requirements. Check with your local Air
Quality Management or Air Pollution Control District for specific requirements.
Emergency stationary internal combustion engines (ICE) may be operated for the purpose of maintenance checks and readiness testing,
provided that the tests are recommended by Federal, State or local government, Generac, or the insurance company associated with the
engine. Maintenance checks and readiness testing of such units is limited to 100 hours per year. There is no time limit on the use of emer-
gency stationary ICE in emergency situations. The purchaser/owner may petition the Administrator for approval of additional hours to be
used for maintenance checks and readiness testing, but a petition t Federal, is not required if the owner maintains records indicating tha
State, or local standards require maintenance and testing of emergency ICE beyond 100 hours per year. Emergency stationary ICE may
operate up to 50 hours per year in non emergency situations, but those 50 hours are counted towards the 100 hours per year provided for
maintenance and testing.
The 50 hours per year for non-emergency situations cannot be used for peak shaving or to generate income for a facility to supply power to
an electric grid or otherwise supply power as part of a financial arrangement with another entity. For purchaser/owner of emergency engines,
any operation other than emergency operation, maintenance and testing, and operation in non-emergency situations for 50 hours per year,
as permitted in this section is prohibited.
If you operate and maintain your certified emergency stationary SI internal combustion engine and emissions control systems in accordance
to the specifications and guidelines in this Owner’s Manual, EPA will not require engine performance testing. If not, your engine will be con-
sidered non-certified and you must demonstrate compliance according to Subpart JJJJ - Standards of Performance for Stationary Spark Igni-
tion Internal Combustion Engines as listed in the Electronic Code of Federal Regulations Title 40 Part 60.
Emission-Related Installation Instructions
Your certified emergency stationary engine has pre-set emission control systems or components that require no adjustment. Inspection and
replacement of an emissions related component is required to be done so in accordance with the requirements cited in the United States
Environmental Protection Agency Warranty Statement or can be arranged by contacting either your selling dealer or a Generac Authorized
Warranty Service dealer, 1-800-333-1322 for the dealer nearest you. Failing to follow t ified engine in a hese instructions when installing a cert
piece of non-road equipment violates federal law 40 CFR 1068.105 (b), subject to fines or penalties as described in the Clean Air Act.
EmsnWrnty001 Revision F (04/15)
United States Environmental Protection Agency Warranty Statement
(Stationary Emergency Spark-Ignited Generators)
Warranty Rights, Obligations and Coverage
The United States Environmental Protection Agency (EPA) and Generac Power Systems, Inc. (Generac) are pleased to explain the Emission
Control System Warranty on your new stationary emergency engine. If during the warranty period, any emission control system or compo-
nent on your engine is found defective in materials or workmanship, Generac will repair your engine at no cost to you for diagnosis, replace-
ment parts and labor provided it be done by a Generac Authorized Warranty Service Facility. Your emission control system may include parts
such as the fuel metering, ignition, and exhaust systems and other related emission related components listed below. Generac will warrant
the emissions control systems on your 2009 and later model year engines provided there has been no abuse, neglect, unapproved modifica-
tion, or improper maintenance of your engine. For engines less than 130 HP the warranty period is two years from the date of sale to the ulti-
mate purchaser. For engines greater than or equal to 130 HP the warranty period is three years or 2500 hours of operation, whichever
comes first, from the date of the engine being placed into service. For high-cost warranted components, the Emission Control System war-
ranty is valid for 5 years or 3500 hours of operation, whichever comes first.
Purchaser's/Owner's Warranty Responsibilities
As the engine purchaser/owner you are responsible for the following: 1) The engine must be installed and configured in accordance to Gen-
erac's installation specifications. 2) The completion of all maintenance requirements listed in your Owner's Manual. 3) Any engine setting
adjustment must be done in accordance and consistent with the instructions in the Owner's Manual. 4) Any emission control system or com-
ponent must be maintained and operated appropriately in order to ensure proper operation of the engine and control system to minimize
emissions at all times.
Generac may deny any/or all Emission Control System Warranty coverage or responsibility of the engine, or an emission control system or
component on your engine thereof, if it has failed due to abuse, neglect, unapproved modification or improper maintenance, or the use of
counterfeit and/or “gray market” parts not made, supplied or approved by Generac. Warranty service can be arranged by contacting either
your selling dealer or a Generac Authorized Warranty Service dealer, 1-800-333-1322 for the dealer nearest you. The purchaser/owner shall
be responsible for any expenses or other charges incurred for service calls and/or tr spection or ansportation of the product to/from the in
repair facilities. The purchaser/owner shall be responsible for any and/or all damages or losses incurred while the engine is being trans-
ported/shipped for inspection or warranty repairs. Contact Generac Power Systems Inc. for additional Emission Control System Warranty
related information, Generac Power Systems, Inc., PO. Box 8, Waukesha, WI 53187, or call 1-800-333-1322 or www.generac.com.
Important Note
This warranty statement explains your rights and obligations under the Emission Control System Warranty, which is provided to you by Gen-
erac pursuant to federal law. Note that this warranty shall not apply to any incidental, consequential, or indirect damages caused by defects
in materials or workmanship or any delay in repair or replacement of the defective part(s). This warranty is in place of all other warranties,
expressed or implied. Specifically, Generac makes no other warranties as to the merchantability or fitness for a particular purpose. Any
implied warranties which are allowed by law, shall be limited in duration to the terms of the express warranty provided herein. Some states
do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Emission Related Parts Include the Following (if so equipped)
*High-Cost Warranted Component
EmsnWrnty001 Revision F (04/15)
1) Fuel Metering System
1.1) Gasoline Carburetor Assembly and Internal Components
A) Fuel Filter, B) Carburetor, C) Fuel Pump
1.2) Carburetion Assembly and Its Components
A) Fuel Controller, B) Carburetor and Its Gaskets,
C) Mixer and Its Gaskets, D) Primary Gas Regulator,
E) Liquid Vaporizer
1.3) Fuel Regulator
2) Air Induction System Including A) Intake Pipe/Manifold,
B) Air Cleaner
3) Ignition System Including A) Spark Plug, B) Ignition Module,
C) Ignition Coil, D) Spark Plug Wires
4) Exhaust System
A) Catalyst Assembly*, B) Exhaust Manifold, C) Muffler,
D) Exhaust Pipe, E) Muffler Gasket
5) Crankcase Breather Assembly Including
A) Breather Connection Tube, B) PCV Valve
6) Oxygen Sensor
7) Diagnostic Emission-Control System
United States Environmental Protection Agency Compliance Requirements
(Stationary Emergency Spark-Ignited Generators)
Purchaser's/Owner's Record Keeping Responsibilities
The United States Environmental Protection Agency (EPA) and Generac Power Systems, Inc. (Generac) are pleased to explain your record
keeping requirements for compliance with Subpart JJJJ- Standards of Performance for Stationary Spark Ignition Internal Combustion
Engines as listed in the Electronic Code of Federal Regulations Title 40 Part 60. As the engine purchaser/owner who operates and maintains
their certified emergency stationary engine and emission control system according to applicable emission related guidelines as specified in
this Owner's Manual, you are required to meet the following notification and record keeping requirements to demonstrate compliance: 1)
Maintain documentation that the engine is certified to meet emission standards. 2) Record keeping of maintenance conducted. 3) Record
keeping of the provision allowing natural gas engines to operate using propane for a maximum of 100 hours per year as an alternate fuel
solely during emergency operations provided the engine is not certified to operate on propane. 4) Meet all compliance notifications submitted
to the purchaser/owner and maintain all supporting documentation. 5) Record keeping of hours of operation, including what classified the
operation as emergency and how many hours are spent for non-emergency operation. For emergency engines greater than or equal to 130
HP, record keeping of hours of operation begins January 1, 2011. For emergency engines less than 130 HP, record keeping of hours of oper-
ation begins January 1, 2009; engines are equipped with non-resettable hour meters to facilitate record keeping.
Specific Air Quality Management or Air Pollution Control Districts may have different and additional record keeping/reporting requirements.
Your permit to construct and/or operate the engine may be contingent upon compliance with those requirements. Check with your local Air
Quality Management or Air Pollution Control District for specific requirements.
Emergency stationary internal combustion engines (ICE) may be operated for the purpose of maintenance checks and readiness testing,
provided that the tests are recommended by Federal, State or local government, Generac, or the insurance company associated with the
engine. Maintenance checks and readiness testing of such units is limited to 100 hours per year. There is no time limit on the use of emer-
gency stationary ICE in emergency situations. The purchaser/owner may petition the Administrator for approval of additional hours to be
used for maintenance checks and readiness testing, but a petition t Federal, is not required if the owner maintains records indicating tha
State, or local standards require maintenance and testing of emergency ICE beyond 100 hours per year. Emergency stationary ICE may
operate up to 50 hours per year in non emergency situations, but those 50 hours are counted towards the 100 hours per year provided for
maintenance and testing.
The 50 hours per year for non-emergency situations cannot be used for peak shaving or to generate income for a facility to supply power to
an electric grid or otherwise supply power as part of a financial arrangement with another entity. For purchaser/owner of emergency engines,
any operation other than emergency operation, maintenance and testing, and operation in non-emergency situations for 50 hours per year,
as permitted in this section is prohibited.
If you operate and maintain your certified emergency stationary SI internal combustion engine and emissions control systems in accordance
to the specifications and guidelines in this Owner’s Manual, EPA will not require engine performance testing. If not, your engine will be con-
sidered non-certified and you must demonstrate compliance according to Subpart JJJJ - Standards of Performance for Stationary Spark Igni-
tion Internal Combustion Engines as listed in the Electronic Code of Federal Regulations Title 40 Part 60.
Emission-Related Installation Instructions
Your certified emergency stationary engine has pre-set emission control systems or components that require no adjustment. Inspection and
replacement of an emissions related component is required to be done so in accordance with the requirements cited in the United States
Environmental Protection Agency Warranty Statement or can be arranged by contacting either your selling dealer or a Generac Authorized
Warranty Service dealer, 1-800-333-1322 for the dealer nearest you. Failing to follow t ified engine in a hese instructions when installing a cert
piece of non-road equipment violates federal law 40 CFR 1068.105 (b), subject to fines or penalties as described in the Clean Air Act.
EmsnWrnty001 Revision F (04/15)
EXPLODED VIEW: MOUNTING BASE 1.6L
DRAWING #: 0G3531
GROUP C
APPLICABLE TO:
REVISION: J-8330-C Page 2 of 2
DATE: 4/8/14
ITEM PART# QTY. DESCRIPTION
1 0G3343 1 MOUNTING BASE 1.6L 2007 C1
2 027482 1 WASHER SHAKEPROOF EXT 5/16 STL
3 070936 2 DAMPENER VIBRATION
4 070936C 2 VIB. ISO. 70-75 DURO
5 039253 12 SCREW HHC M8-1.25 X 20 G8.8
6 022145 16 WASHER FLAT 5/16 ZINC
7 022129 16 WASHER LOCK M8-5/16
8 045771 4 NUT HEX M8-1.25 G8 YEL CHR
9 071956 4 WASHER FLAT M8
10 051730 4 SCREW HHC M8-1.25 X 60 G8.8
11 021991 1 EARTH STRAP
13 026850 1 WASHER SHAKEPROOF EXT 1/4 STL
14 0G3461 2 ALTERNATOR SUPPORT BLOCK OFF
15 055414 1 LUG SLDLSS #2-#8 X 17/64 CU
16 042568 1 SCREW HHC M6-1.0 X 20 C8.8
17 022097 1 WASHER LOCK M6-1/4
18 022473 5 WASHER FLAT 1/4-M6 ZINC
19 025507 1 WASHER LOCK EXT 7/16 STL
EXPLODED VIEW: EV BATTERY C1 1.6L
DRAWING #: 0G4067
GROUP C
ITEM PART# QTY. DESCRIPTION
REVISION: K-1287-B Page 2 of 2
DATE: 11/20/14
1 0F3408C 1 BATTERY TRAY, C1 & C2
2 0F3411 1 STRAP BATTERY RETAINMENT
3 025507 2 WASHER SHAKEPROOF EXT 7/16 STL
4 059980 2 SCREW HHC M10-1.5 X 25 G10.9
5 046526 2 WASHER LOCK M10
6 077483 REF BATTERY 12VDC 75-AH 26
7 050331A REF BATTERY POST COVER RED +
8 050331 REF BATTERY POST COVER BLK -
9 038805J 1 CABLE BATTERY BLACK #1 X 30.00
10 038804M 1 CABLE BATTERY RED #1 X 21.00
11 045771 REF NUT HEX M8-1.25 G8 YEL CHR
12 022131 2 WASHER FLAT 3/8-M10 ZINC
13 027482 1 WASHER SHAKEPROOF EXT 5/16 STL
14 0F3976 1 BOOT CONTACTOR CABLES
15 0C2454 4 SCREW THF M6-1 X 16 N WA Z/JS
16 022145 REF WASHER FLAT 5/16-M8 ZINC
17 055934H 1 CLAMP STL/VNL .62 X .406 Z
NOTE: WHEN INSTALLING BATTERY, TUCK BATTERY’S LIFTING STRAP ALONG THE LEFT SIDE OF BATTERY ( SIDE OPPOSITE RADIATOR) BEFORE
CONNECTING THE BATTERY CABLES.
1 0F3408C 1 BATTERY TRAY, C1 & C2
2 0F3411 1 STRAP BATTERY RETAINMENT
3 025507 1 WASHER SHAKEPROOF EXT 7/16 STL
4 059980 1 SCREW HHC M10-1.5 X 25 G10.9
5 046526 1 WASHER LOCK M10
6 077483 REF BATTERY 12VDC 75-AH 26
7 050331A REF BATTERY POST COVER RED +
8 050331 REF BATTERY POST COVER BLK -
9 038805J 1 CABLE BATTERY BLACK #1 X 30.00
10 038804M 1 CABLE BATTERY RED #1 X 21.00
11 045771 REF NUT HEX M8-1.25 G8 YEL CHR
12 022131 1 WASHER FLAT 3/8-M10 ZINC
13 027482 1 WASHER SHAKEPROOF EXT 5/16 STL
14 0F3976 1 BOOT CONTACTOR CABLES
15 0C2454 4 SCREW THF M6-1 X 16 N WA Z/JS
16 022145 REF WASHER FLAT 5/16-M8 ZINC
NOTE: WHEN INSTALLING BATTERY, TUCK BATTERY’S LIFTING STRAP ALONG
THE LEFT SIDE OF BATTERY ( SIDE OPPOSITE RADIATOR) BEFORE
CONNECTING THE BATTERY CABLES.
EXPLODED VIEW: CONNECTION BOX C1 CPL
DRAWING #: 0H7234
GROUP A
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8409-M
Page 4 of 8
DATE: 4/29/14
1 0H6795 1 CONBOX BACK/SIDES C1 CPL
2 0H6796 1 CONBOX TOP C1 CPL
(4)3 0H67330ST0R 1 BRACKET GIMBAL CONTROL PNL RAW
4 0H7115 2 KNOB M6-1.0 CONTROL PANEL
5 022097 2 WASHER LOCK M6-1/4
6 022473 4 WASHER FLAT 1/4-M6 ZINC
(3)7 SEE CHART 1 CIRCUIT BREAKER
8 052777 3 WASHER FLAT M3
9 043182 3 WASHER LOCK M3
10 051714 3 NUT HEX M3-0.5 G8 CLEAR ZINC
(4)11 0H81040AS0R 1 COVER DPE BREAKER NEXUS
12 045764 2 SCREW HHTT M4-0.7 X 8 ZP
13 022264 3 WASHER LOCK #8-M4
14 0A9457 1 DECAL NEUTRAL
15 REF 1 ASSY CTRL PROGRAMMED
16 0C2454 19 SCREW HWHT M6-1 X 16 N WA Z/JS
(2)17 0A1354A 1 REGULATOR - DC ALT
18 0D3700 6 NUT FLANGE M6-1.0 NYLOK
(4)19 0H88380ST0R 1 SHIELD HIGH/LOW C1 RAW
20 056739 1 RELAY SOLENOID 12VDC PNL MNT
21 0F5458 12 SCREW HHSP #10 X 3/8 HI-LOW
22 042568 2 SCREW HHC M6-1.0 X 20 C8.8
23 051716 2 NUT HEX M5-0.8 G8 CLEAR ZINC
24 049226 2 WASHER LOCK M5
26 0D7177V 2 DIODE BRIDGE 1P 35A 1000V
27 0F5752F 1 RES WW 15R 5% 25W QK CONN
28 0H6267 1 COVER VOLTAGE SHIELD
29 056326 2 TRIM VINYL BLACK 1/8GP (3”LG)
30 0G3524 1 COVER BELL HOUSING CONBOX
(1)31 0D7393T REF TERM BLOCK 3P UL 12-20AWG
(1)32 0D7393U REF TERM BLOCK 4P UL 12-20AWG
(1)33 0F5376S0AR REF MX150L SLRRMNT 22-18 8P W/O GA
(1)34 0F5396S0AR REF MX150L SLRRMNT 22-18 12P W/OGA
35 057073 1 JUNCTION BLOCK 3/8-16
36 0C2265 3 SCREW PHTT M4-0.7 X 12 ZP
37 057329 1 LUG SLDLSS 350-#6X13/32 AL/CU
38 022237 1 WASHER LOCK 3/8
39 022241 1 NUT HEX 3/8-16 STEEL
40 025433 1 LUG SLDLSS #6-14 X 13/64 CU
41 023762 1 WASHER LOCK EXT #10 STL
42 0H7292 1 DECAL CUSTOMER CONTROL CONNECT
43 0H7293 1 DECAL CONBOX TB1 CONNECTIONS
44 029289 1 TAPE ELEC 1/2 FOAM (62” LG)
45 0J0489 1 DECAL CUSTOMER POWER CONNECT
46 0A2115 2 WASHER NYLON .257
47 0F6146 1 HANG TAG 2 WIRE START (NOT SHOWN)
48 0H6692 1 HARN CONBOX NEXUS (NOT SHOWN)
49 0D7178T REF FUSE ATO TYPE 7.5AMP (BROWN)
50 067210A 1 DECAL GROUND LUG
51 0J6701 1 GASKET WIRE ENTRY COVER
52 0H8006 1 DECAL CAUTION ELEC SHOCK SM
53 055934 1 HOSE CLAMP
UL CIRCUIT BREAKER (225AF)
A 0G5249 REF CB 150A 2 POLE 240V 225AF
B 0H6846 1 COVER CB G 225AF C1 CONBOX
C 0F8432A 1 INSULATOR CB 2P 225AF
D 0G5734 1 SPRT CIRCUIT BREAKER G 225AF
E 038150 2 WASHER FLAT #8 ZINC
F 022264 2 WASHER LOCK #8-M4
G 022471 2 NUT HEX #8-32 STEEL
H 0C2454 10 SCREW HWHT M6-1 X 16 N WA Z/JS
J 053640 2 SCREW RHM #8-32 X 3-1/4
K 0F8843 2 BUS BAR 200A LUG ADAPTOR
EXPLODED VIEW: CONNECTION BOX C1 CPL
DRAWING #: 0H7234
GROUP A
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8409-M
Page 5 of 8
DATE: 4/29/14
L 049897 4 SCREW SHC M8-1.25 X 20 G8
M 022129 6 WASHER LOCK M8-5/16
P 045771 2 NUT HEX M8-1.25 G8 CLEAR ZINC
R 043107 2 SCREW HHC M8-1.25 X 25 C8.8
S 0F8451 2 LUG SLDLSS 300 MCM-6 AL/CU
T 0G3259 1 DECAL TERMINAL SHOCK HZD BI
U 0J78230AS0R 1 SHIELD CB HANDLE CONBOX
V 029289 1 TAPE ELEC 1/2 FOAM
W 036261 4 RIVET POP .125 X .275 SS
(1) ITEMS INCLUDED WITH HARNESS P/N 0H6692.
(2) ITEMS USED ON 1.6L MODELS ONLY.
(3) SEE “C1 DPE BREAKER SELECTION” TABLE.
(4) SHEET METAL PARTS LISTED IN THE BOM TABLE ARE REPRESENTING GENERIC PARTS (NO COLOR)
MANUFACTURING: FOR CORRECT MATERIAL AND COLOR REFER TO XA BOM.
CUSTOMER: WHEN ORDERING REPLACEMENT PARTS ENTER BASE NUMBER (FIRST 6 DIGITS ONLY) IN THE
SYSTEM FOR CORRECT MATERIAL AND COLOR (FOR REFERENCE SEE GUIDELINE 0H7169).
EXPLODED VIEW: CONNECTION BOX C1 CPL
DRAWING #: 0H7234
GROUP A
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8409-M
Page 6 of 8
DATE: 4/29/14
UL CIRCUIT BREAKER (CC 2P)
A 0H4745 REF CB 0100A 2P 240V E CC LL
0H4746 REF CB 0125A 2P 240V E CC LL
0H4747 REF CB 0150A 2P 240V E CC LL
B 0H6847 1 COVER CB E CC 2P C1 CONBOX
C 051716 2 NUT HEX M5-0.8 G8 CLEAR ZINC
D 0H4656 1 CIRCUIT BREAKER SUPPORT (CC)
E 038150 2 WASHER FLAT #8 ZINC
F 022264 2 WASHER LOCK #8-M4
G 022471 2 NUT HEX #8-32 STEEL
H 0C2454 10 SCREW HWHT M6-1 X 16 N WA Z/JS
J 053640 2 SCREW RHM #8-32 X 3-1/4
K 091526 2 SCREW PPHM M5-0.8 X 12 ZNC
L 023897 4 WASHER FLAT #10 ZINC
M 049226 2 WASHER LOCK M5
N 0H4698 1 INSULATOR CB 2P E TYPE CC
P 0J78230AS0R 1 SHIELD CB HANDLE CONBOX
Q 029289 1 TAPE ELEC 1/2 FOAM
R 036261 4 RIVET POP .125 X .275 SS
UL CIRCUIT BREAKER (CC/FG (3P) )
A 0H4913 REF CB 0100 3P 240V E CC LL
0H4914 REF CB 0125 3P 240V E CC LL
0H5488 REF CB 0080 3P 600V E FG LL
0H5489 REF CB 0090 3P 600V E FG LL
B 0H7294 1 CB COVER E CC/FG 3P C1 CONBOX
C 0H4698A 1 INSULATOR CB 3P E TYPE CC/FG
D 0H4656 REF CIRCUIT BREAKER SUPPORT (CC)
0H5604 REF CIRCUIT BREAKER SUPPORT (FG)
E 038150 4 WASHER FLAT #8 ZINC
F 022264 4 WASHER LOCK #8-M4
G 022471 4 NUT HEX #8-32 STEEL
H 0C2454 10 SCREW HWHT M6-1 X 16 N WA Z/JS
J 0H5721 4 SCREW PPHM #8-32 X 1-3/4 ZINC (CC)
0H5721 4 SCREW PPHM #8-32 X 1-3/4 ZINC (FG)
K 091526 3 SCREW PPHM M5-0.8 X 12 ZNC
L 023897 6 WASHER FLAT #10 ZINC
M 049226 3 WASHER LOCK M5
N 051716 3 NUT HEX M5-0.8 G8 CLEAR ZINC
P 0J78230AS0R 1 SHIELD CB HANDLE CONBOX
Q 029289 1 TAPE ELEC 1/2 FOAM
R 036261 4 RIVET POP .125 X .275 SS
EXPLODED VIEW: CONNECTION BOX C1 CPL
DRAWING #: 0H7234
GROUP A
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8409-M
Page 7 of 8
DATE: 4/29/14
UL CIRCUIT BREAKER (BQ 2P)
A 0D5543 REF CB 0090A 2P 240V S BQ2 LL
0D5544 REF CB 0100A 2P 240V S BQ2 LL
0A2077 REF CB 0125A 2P 240V S BQ2 LL
B 0H6842 1 COVER CB S BQ2 C1 CONBOX
C 0E7890 1 BRKT CB MTG BACK
D 0G4497 1 CIRCUIT BREAKER SUPPORT (BQ)
E 052619 2 SCREW HHC M5-0.8 X 20 G8.8
F 023897 4 WASHER FLAT #10 ZINC
G 049226 2 WASHER LOCK M5
H 0C2454 10 SCREW HWHT M6-1 X 16 N WA Z/JS
J 051716 2 NUT HEX M5-0.8 G8 CLEAR ZINC
K 0C2265 2 SCREW PHTT M4-0.7 X 12 ZP
L 022264 2 WASHER LOCK #8-M4
M 0J78230AS0R 1 SHIELD CB HANDLE CONBOX
N 029289 1 TAPE ELEC 1/2 FOAM
P 036261 4 RIVET POP .125 X .275 SS
UL CIRCUIT BREAKER (BQ 3P)
A 062812 REF CB 0080A 3P 240V S BQ3 LL
053691 REF CIRCT BRK 90 X 3 ITE BQ3-B090
040532 REF CB 0100A 3P 240V S BQ3 LL
B 0H6843 1 COVER CB S BQ3 C1 CONBOX
C 0E6002 1 MTG TRACK BQ SIEMENS CB 3P
D 0G4497 1 CIRCUIT BREAKER SUPPORT (BQ)
E 052619 3 SCREW HHC M5-0.8 X 20 G8.8
F 023897 6 WASHER FLAT #10 ZINC
G 049226 3 WASHER LOCK M5
H 0C2454 10 SCREW HWHT M6-1 X 16 N WA Z/JS
J 051716 3 NUT HEX M5-0.8 G8 CLEAR ZINC
K 0C2265 2 SCREW PHTT M4-0.7 X 12 ZP
L 022264 2 WASHER LOCK #8-M4
M 0J78230AS0R 1 SHIELD CB HANDLE CONBOX
N 029289 1 TAPE ELEC 1/2 FOAM
P 036261 4 RIVET POP .125 X .275 SS
UL CIRCUIT BREAKER (ED 3P)
A 0D5552 REF CB 0050A 3P 480V S ED4 LL
0D5556 REF CB 0090A 3P 480V S ED4 LL
0D5557 REF CB 0100A 3P 480V S ED4 LL
0D9693 REF CB 0125A 3P 480V S ED4 LL
B 0H6844 1 COVER CB S ED3 C1 CONBOX
C 0G4498 1 CIRCUIT BREAKER SUPPORT (ED)
D 038150 4 WASHER FLAT #8 ZINC
E 022264 4 WASHER LOCK #8-M4
F 022471 4 NUT HEX #8-32 STEEL
G 0A8278 3 SCREW SHC 1/4-28 X 3/4 G8.8 NZ
H 0C2454 10 SCREW HWHT M6-1 X 16 N WA Z/JS
J 066715 4 SCREW RHM #8-32 X 4-1/2
K 022097 3 WASHER LOCK M6-1/4
L 0D5621 3 WASHER-STEP 1/2ODX9/32ID BRASS
M 0J78230AS0R 1 SHIELD CB HANDLE CONBOX
N 029289 1 TAPE ELEC 1/2 FOAM
P 036261 4 RIVET POP .125 X .275 SS
EXPLODED VIEW: CONNECTION BOX C1 CPL
DRAWING #: 0H7234
GROUP A
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8409-M
Page 8 of 8
DATE: 4/29/14
UL CIRCUIT BREAKER (QN2 2P)
A 0E7283 REF CB 0150A 2P 240V S QN2 LL
B 0H6845 1 COVER CB S QN2 C1 CONBOX
C 0E3664 1 BASE, QN CIRCUIT BREAKER
D 0G4112 1 BREAKER SUPPORT BRACKET 30KW
E 074908 2 SCREW HHTT M5-0.8 X 10 BP
F 0C2454 10 SCREW HWHT M6-1 X 16 N WA Z/JS
G 0J78230AS0R 1 SHIELD CB HANDLE CONBOX
H 029289 1 TAPE ELEC 1/2 FOAM
J 036261 4 RIVET POP .125 X .2
EXPLODED VIEW: EV ENCLOSURE C1 CPL
DRAWING #: 0G3534
GROUP F
ITEM PART# QTY. DESCRIPTION
REVISION: J-1720-K Page 2 of 2
DATE: 3/23/12
(2) 1 0G33370AL0R 1 ROOF 1.6L C1
(2) 2 0J14640AL0R 1 REAR INTAKE WRAP C1
(1) 3 077992 10 NUT HEX LOCK M6-1.0 SS NY INS
(2) 4 0J14630AL0R 2 DOOR LEFT/RIGHT SIDE C1
6 0F4487A 1 ASSY ACCESS COVER
7 022127 1 NUT HEX 1/4-20 STEEL
8 022097 1 WASHER LOCK M6-1/4
9 022473 10 WASHER FLAT 1/4-M6 ZINC
(1)10 0C2454 8 SCREW THF M6-1 X 16 N WA Z/JS
11 0F5048D 2 VISE-ACTION LATCH, SLOTTED CIR
12 0F5049B 2 PULL TAB DOOR LOCK SS
13 0F8869D 1 KEY VISE-ACTION LATCH,SLOT CIR
14 089961 1 FOAM STRIP 3/4"WIDE X 3/16"THK (294”LG)
15 078115 8 WASHER SELF LOCKING DOME
16 0H7518 2 INSULATION SIDE DOOR C1
17 0H7518A 1 INSULATION ROOF C1
(1)19 0E3257 6 SCREW HWHTF M6-1.0 X 16
20 0912970090 2 ASSY WIRE 14AWG GRN/YEL (32.25”LG)
21 0H7518B 1 INSULATION REAR C1
23 0C8566 10 SCREW HHFC M6-1.0 X 20 G8.8
24 0H0412 10 NUT SPRINGCLIP M6-1.0
25 022097 8 WASHER LOCK M6-1/4
(3) 26 0H7529 1 FOIL ALUMINUM WITH ADHESIVE
27 0H1208A 1 RF COVER PLATE-PLASTIC-BISQUE
0H1208B 1 RF COVER PLATE-PLASTIC-GREY
(2) 28 0G33350AL0R 1 FRONT DISCHARGE WRAP 1.6L C1
(1)29 0A1658 2 WASHER LOCK SPECIAL 1/4"
(1)ENCLOSURE NOTE: ALL PANELS THAT FASTEN TO THE ROOF MUST BE SECURED USING I/N 10 (THREAD FORMING FASTENER) AND I/N 3 (LOCK NUT) AND
TO INCLUDE AT LEAST ONE CONNECTION POINT USING I/N 19 (THREAD FORMING FASTENER) WITH I/N 3 (LOCK NUT) TO EACH PANEL. LOCK NUT IS TO BE
INSTALLED AFTER THREAD FORMING FASTENER HAS PENETRATED THROUGH EXTRUSION IN ENCLOSURE PANELS. ALL PANEL TO BASEFRAME
CONNECTIONS TO INCLUDE AT LEAST ONE CONNECTION POINT USING I/N 29 (WASHER SPECIAL).
(2) SHEET METAL PARTS LISTED IN THE BOM TABLE ARE REPRESENTING GENERIC PARTS (NO COLOR)
MANUFACTURING: FOR CORRECT MATERIAL AND COLOR REFER TO AS400 BOM.
CUSTOMER: WHEN ORDERING REPLACEMENT PARTS ENTER BASE NUMBER (FIRST 6 DIGITS ONLY) IN THE SYSTEM FOR CORRECT MATERIAL
AND COLOR (FOR REFERENCE SEE GUIDELINE 0H7169).
(3) USED ON 1.5L / 1.6L UNITS ONLY.1
EXPLODED VIEW: EV FUELSYS NG/LPV 1.5L
DRAWING #: 0J3226
GROUP E
APPLICABLE TO:
REVISION: K-3796-F Page 2 of 2
DATE: 8/31/15
ITEM PART# QTY. DESCRIPTION
1 025870 1 NUT WING 1/4-20
2 0A5547 1 COVER AIR CLEANER
(2)3 062522 1 STUD TH 1/4-20 X 3 G2 ZNC FULL
4 022127 1 NUT HEX 1/4-20 STEEL
5 059402 1 FILTER ELEMENT
6 091526 4 SCREW PPHM M5-0.8 X 12 ZNC
7 049226 4 WASHER LOCK M5
8 0E0519A 1 ADAPTER, CARBURETOR W/PVC CONN
9 048031J 4 CLAMP HOSE BAND .63
10 0E6586 1 GASKET BOSCH 32 & 40
11 0G1397F 1 FUEL REG. REWORK 1.5L
12 0F7790 1 VENTURI THROTTLE 21MM
13 0E7121 2 O-RING 47.625 ID X 2.38 WIDTH
14 0G4573C 1 MIXER ACTUATOR 32MM MACHINED
15 0G0153 1 BARBED EL 1/2"NPT X 3/4 HOSE
16 0E6586A 1 GASKET BOSCH 32
17 057823 2 CLAMP HOSE #10 .56-1.06
18 035685 2 CLAMP HOSE #28 1.32-2.25
19 057753B 1 HOSE 1.5 ID X 2 LG 20R4
20 0E4395 1 ACTUATOR BOSCH 32 GOVERNOR
21 022129 2 WASHER LOCK M8-5/16
22 049340 1 BARBED EL 90 1/4NPT X 3/8
(1)24 026915 1 NIPPLE CLOSE 3/4 X 1.375
25 022145 2 WASHER FLAT 5/16 ZINC
26 047290 1 HOSE 3/8 ID SINGLE BRAID (20” LG)
27 0J15560227 REF VALVE, PCV
30 059057 1 HOSE 3/4 ID SAE-30R2 (16.50"LG)
31 045771 2 NUT HEX M8-1.25 G8 YEL CHR
32 0D2157 4 SCREW SHC M6-1.0 X 50 C8.8
33 022097 5 WASHER LOCK M6-1/4
34 039253 2 SCREW HHC M8-1.25 X 20 G8.8
35 0G9348 1 ASSY REG INLET NPT FITTINGS
(1)36 026812 2 ELBOW 90D 3/4 NPT
(1)37 076691 1 NIPPLE PIPE 3/4NPTX4.5 BLK IRN
(1)38 026490 1 NIPPLE PIPE 3/4NPT X 2
(1)39 075580 1 FLANGE FUEL INLET
40 047290 1 HOSE 3/8 ID SINGLE BRAID (12”LG)
41 0H5476 1 HARN FUEL JUMPER SINGLE REG
43 0J15560228 REF GROMMET PCV VALVE
44 022473 1 WASHER FLAT 1/4-M6 ZINC
(1) INCLUDED IN ITEM 35 (ASSY REG INLET NPT FITTINGS)
(2) APPLY MEDIUM STRENGTH BLUE THREAD LOCKING FLUID TO THREADS.
EXPLODED VIEW: EV FUELSYS NG/LPV 1.5L
DRAWING #: 0J3226
GROUP E
APPLICABLE TO:
REVISION: K-3796-F Page 2 of 2
DATE: 8/31/15
ITEM PART# QTY. DESCRIPTION
1 025870 1 NUT WING 1/4-20
2 0A5547 1 COVER AIR CLEANER
(2)3 062522 1 STUD TH 1/4-20 X 3 G2 ZNC FULL
4 022127 1 NUT HEX 1/4-20 STEEL
5 059402 1 FILTER ELEMENT
6 091526 4 SCREW PPHM M5-0.8 X 12 ZNC
7 049226 4 WASHER LOCK M5
8 0E0519A 1 ADAPTER, CARBURETOR W/PVC CONN
9 048031J 4 CLAMP HOSE BAND .63
10 0E6586 1 GASKET BOSCH 32 & 40
11 0G1397F 1 FUEL REG. REWORK 1.5L
12 0F7790 1 VENTURI THROTTLE 21MM
13 0E7121 2 O-RING 47.625 ID X 2.38 WIDTH
14 0G4573C 1 MIXER ACTUATOR 32MM MACHINED
15 0G0153 1 BARBED EL 1/2"NPT X 3/4 HOSE
16 0E6586A 1 GASKET BOSCH 32
17 057823 2 CLAMP HOSE #10 .56-1.06
18 035685 2 CLAMP HOSE #28 1.32-2.25
19 057753B 1 HOSE 1.5 ID X 2 LG 20R4
20 0E4395 1 ACTUATOR BOSCH 32 GOVERNOR
21 022129 2 WASHER LOCK M8-5/16
22 049340 1 BARBED EL 90 1/4NPT X 3/8
(1)24 026915 1 NIPPLE CLOSE 3/4 X 1.375
25 022145 2 WASHER FLAT 5/16 ZINC
26 047290 1 HOSE 3/8 ID SINGLE BRAID (20” LG)
27 0J15560227 REF VALVE, PCV
30 059057 1 HOSE 3/4 ID SAE-30R2 (16.50"LG)
31 045771 2 NUT HEX M8-1.25 G8 YEL CHR
32 0D2157 4 SCREW SHC M6-1.0 X 50 C8.8
33 022097 5 WASHER LOCK M6-1/4
34 039253 2 SCREW HHC M8-1.25 X 20 G8.8
35 0G9348 1 ASSY REG INLET NPT FITTINGS
(1)36 026812 2 ELBOW 90D 3/4 NPT
(1)37 076691 1 NIPPLE PIPE 3/4NPTX4.5 BLK IRN
(1)38 026490 1 NIPPLE PIPE 3/4NPT X 2
(1)39 075580 1 FLANGE FUEL INLET
40 047290 1 HOSE 3/8 ID SINGLE BRAID (12”LG)
41 0H5476 1 HARN FUEL JUMPER SINGLE REG
43 0J15560228 REF GROMMET PCV VALVE
44 022473 1 WASHER FLAT 1/4-M6 ZINC
(1) INCLUDED IN ITEM 35 (ASSY REG INLET NPT FITTINGS)
(2) APPLY MEDIUM STRENGTH BLUE THREAD LOCKING FLUID TO THREADS.
EXPLODED VIEW: EV ENGCOMPRT 1.5L
DRAWING #: 0J3554
GROUP D
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8330-D Page 3 of 4
DATE: 4/8/14
1 0J1556 REF ENGINE GENERAC 1.5L G11 CERT
2 0J3704 1 ENGINE PLATE 1.5L 6MM
3 0G0820B REF HOUSING BLOWER LG PILOT
4 0G7461 1 STARTER MOTOR 12V
5 0G0839 2 ENGINE MOUNTING FOOT STAMPING
6 0G0781 1 EXHAUST MANIFOLD 1.6L MACHINED
7 0J3061A 1 INTAKE MANIFOLD MACH 1.5L G11
8 0G4059 1 SHIELD 1.6L EXHAUST HEAT
9 0G4604 1 DC ALTERNATOR ADAPTER MACHINED
10 0G3424 1 PULLEY CRANKSHAFT MACHINED
11 0G0786 1 WASHER PULLEY
12 0G4605 1 BRACKET TENSIONER DC ALT
13 0F9617A 1 SPACER ALTERNATOR
14 0A1354B 1 DC ALTERNATR HAN-KOK
15 0G0823 1 V-BELT 3/8 X 30.6
16 0J4472 1 SPARK PLUG WIRE SET 1.5L G11
17 0D2244M 1 ASSY MAGPICKUP (3/8-24 MALE)
18 0G8759 2 BUSHING GUIDE 19.3MM LONG
19 0C5479 1 SCREW HHC M12-1.5 X 40 G10.9
20 059980 9 SCREW HHC M10-1.5 X 25 G10.9
21 046526 9 WASHER LOCK M10
22 022131 21 WASHER FLAT 3/8-M10 ZINC
23 0G3922 1 NUT HEX M10-1.5 CLASS 10 ZINC
24 0J15560163 REF GASKET, EXHAUST MANIFOLD
25 0J4719 1 GASKET INTAKE MANIFOLD G11
26 052858 16 NUT TOP LOCK FL M8-1.25
27 051735 1 SCREW HHC M10-1.5 X 70 G8.8
28 0G9255 4 SCREW HHC M10-1.25 X 100 PC8.8
29 052830 4 SCREW HHC M10-1.25 X 45 C8.8
30 039414 1 SCREW HHC M8-1.25 X 35 G8.8
31 022129 4 WASHER LOCK M8-5/16
32 022145 4 WASHER FLAT 5/16-M8 ZINC
33 029333A 1 TIE WRAP UL 7.4" X .19" BLK (NOT SHOWN)
34 057821 3 SCREW HHC M8-1.25 X 40 G8.8
35 045771 3 NUT HEX M8-1.25 G8 CLEAR ZINC
36 022507 2 SCREW HHC 1/4-20 X 1/2 G5
37 022097 6 WASHER LOCK M6-1/4
38 022473 6 WASHER FLAT 1/4-M6 ZINC
39 0E3257 3 SCREW HWHTF M6-1.0 X 16
40 0A5768 3 WASHER FLAT M10 HEAVY DUTY
41 0E0502A 1 TEMPERATURE SENDER DELPHI M12
42 035579 1 BSHG RDCR HEX 1/4 TO 1/8
43 0H7435 1 HARN LOW OIL PRESS SWITCH ASSY
44 081816 2 SCREW HHC M12-1.75 X 55 C10.9
45 0J15560235 REF SPARK PLUG
46 069860C 1 HOSE OIL DRAIN ASSY 21"
47 069811 1 CAP HEX 1/4 NPT BRASS
48 0D8427 10 WASHER LOCK M10 RIBBED ZINC
49 0G3118A 1 WASHER, NITRILE SEAL M12
50 022152 8 WASHER LOCK #10
51 057823 1 CLAMP HOSE #10 .56-1.06
52 0A8830 25 WASHER FLAT .34 ID X .75 OD
53 0J4554 1 HARN ENG 1.5L G11 NEXUS (NOT SHOWN)
54 0E7080 REF OIL FILTER 1.6,2.5,3.0,4.2L G3
55 077043H 1 CONDUIT FLEX .25"ID (6” LG)
56 0G8853 4 COIL 2.4L G2 IGNITION
57 0J4906 1 ASSY BRACKET COIL 1.5L G11
58 0C7649 1 CLAMP HOSE .38-.87
59 0J4694 1 BANJO ASSY M16-1.0
60 046525 8 NUT HEX M10-1.25 G8 YEL CHR
(1)61 0G34330ST0R REF BRACKET FAN ALT ADAPTER 1.6L
EXPLODED VIEW: EV ENGCOMPRT 1.5L
DRAWING #: 0J3554
GROUP D
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8330-D Page 3 of 4
DATE: 4/8/14
1 0J1556 REF ENGINE GENERAC 1.5L G11 CERT
2 0J3704 1 ENGINE PLATE 1.5L 6MM
3 0G0820B REF HOUSING BLOWER LG PILOT
4 0G7461 1 STARTER MOTOR 12V
5 0G0839 2 ENGINE MOUNTING FOOT STAMPING
6 0G0781 1 EXHAUST MANIFOLD 1.6L MACHINED
7 0J3061A 1 INTAKE MANIFOLD MACH 1.5L G11
8 0G4059 1 SHIELD 1.6L EXHAUST HEAT
9 0G4604 1 DC ALTERNATOR ADAPTER MACHINED
10 0G3424 1 PULLEY CRANKSHAFT MACHINED
11 0G0786 1 WASHER PULLEY
12 0G4605 1 BRACKET TENSIONER DC ALT
13 0F9617A 1 SPACER ALTERNATOR
14 0A1354B 1 DC ALTERNATR HAN-KOK
15 0G0823 1 V-BELT 3/8 X 30.6
16 0J4472 1 SPARK PLUG WIRE SET 1.5L G11
17 0D2244M 1 ASSY MAGPICKUP (3/8-24 MALE)
18 0G8759 2 BUSHING GUIDE 19.3MM LONG
19 0C5479 1 SCREW HHC M12-1.5 X 40 G10.9
20 059980 9 SCREW HHC M10-1.5 X 25 G10.9
21 046526 9 WASHER LOCK M10
22 022131 21 WASHER FLAT 3/8-M10 ZINC
23 0G3922 1 NUT HEX M10-1.5 CLASS 10 ZINC
24 0J15560163 REF GASKET, EXHAUST MANIFOLD
25 0J4719 1 GASKET INTAKE MANIFOLD G11
26 052858 16 NUT TOP LOCK FL M8-1.25
27 051735 1 SCREW HHC M10-1.5 X 70 G8.8
28 0G9255 4 SCREW HHC M10-1.25 X 100 PC8.8
29 052830 4 SCREW HHC M10-1.25 X 45 C8.8
30 039414 1 SCREW HHC M8-1.25 X 35 G8.8
31 022129 4 WASHER LOCK M8-5/16
32 022145 4 WASHER FLAT 5/16-M8 ZINC
33 029333A 1 TIE WRAP UL 7.4" X .19" BLK (NOT SHOWN)
34 057821 3 SCREW HHC M8-1.25 X 40 G8.8
35 045771 3 NUT HEX M8-1.25 G8 CLEAR ZINC
36 022507 2 SCREW HHC 1/4-20 X 1/2 G5
37 022097 6 WASHER LOCK M6-1/4
38 022473 6 WASHER FLAT 1/4-M6 ZINC
39 0E3257 3 SCREW HWHTF M6-1.0 X 16
40 0A5768 3 WASHER FLAT M10 HEAVY DUTY
41 0E0502A 1 TEMPERATURE SENDER DELPHI M12
42 035579 1 BSHG RDCR HEX 1/4 TO 1/8
43 0H7435 1 HARN LOW OIL PRESS SWITCH ASSY
44 081816 2 SCREW HHC M12-1.75 X 55 C10.9
45 0J15560235 REF SPARK PLUG
46 069860C 1 HOSE OIL DRAIN ASSY 21"
47 069811 1 CAP HEX 1/4 NPT BRASS
48 0D8427 10 WASHER LOCK M10 RIBBED ZINC
49 0G3118A 1 WASHER, NITRILE SEAL M12
50 022152 8 WASHER LOCK #10
51 057823 1 CLAMP HOSE #10 .56-1.06
52 0A8830 25 WASHER FLAT .34 ID X .75 OD
53 0J4554 1 HARN ENG 1.5L G11 NEXUS (NOT SHOWN)
54 0E7080 REF OIL FILTER 1.6,2.5,3.0,4.2L G3
55 077043H 1 CONDUIT FLEX .25"ID (6” LG)
56 0G8853 4 COIL 2.4L G2 IGNITION
57 0J4906 1 ASSY BRACKET COIL 1.5L G11
58 0C7649 1 CLAMP HOSE .38-.87
59 0J4694 1 BANJO ASSY M16-1.0
60 046525 8 NUT HEX M10-1.25 G8 YEL CHR
(1)61 0G34330ST0R REF BRACKET FAN ALT ADAPTER 1.6L
EXPLODED VIEW: EV ENGCOMPRT 1.5L
DRAWING #: 0J3554
GROUP D
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8330-D Page 4 of 4
DATE: 4/8/14
62 049541 1 SCREW HHC M10-1.5 X 35 G8.8
63 047411 4 SCREW HHC M6-1.0 X 16 C8.8
64 023897 8 WASHER FLAT #10 ZINC
65 0F4001E 1 ANCHOR HARNESS
66 0J5047 1 PLUG FREEZE
67 034413 8 SCREW HHM #10-32 X 1-1/4
68 045773 2 NUT HEX M12-1.75 G8 YEL CHR
69 051769 2 WASHER LOCK M12
70 049808 4 WASHER FLAT M12
71 077996 1 CAP ANTIFREEZE 5/8"ID X 1.2"LG
NOTES (UNLESS OTHERWISE SPECIFIED):
(1) SHEET METAL PARTS LISTED IN THE BOM TABLE ARE REPRESENTING GENERIC PARTS (NO COLOR)
MANUFACTURING: FOR CORRECT MATERIAL AND COLOR REFER TO XA BOM.
CUSTOMER: WHEN ORDERING REPLACEMENT PARTS ENTER BASE NUMBER (FIRST 6 DIGITS ONLY) IN THE SYSTEM FOR
CORRECT MATERIAL AND COLOR (FOR REFERENCE SEE GUIDELINE 0H7169).
EXPLODED VIEW: EV ENGCOMPRT 1.5L
DRAWING #: 0J3554
GROUP D
APPLICABLE TO:
ITEM PART# QTY. DESCRIPTION
REVISION: J-8330-D Page 4 of 4
DATE: 4/8/14
62 049541 1 SCREW HHC M10-1.5 X 35 G8.8
63 047411 4 SCREW HHC M6-1.0 X 16 C8.8
64 023897 8 WASHER FLAT #10 ZINC
65 0F4001E 1 ANCHOR HARNESS
66 0J5047 1 PLUG FREEZE
67 034413 8 SCREW HHM #10-32 X 1-1/4
68 045773 2 NUT HEX M12-1.75 G8 YEL CHR
69 051769 2 WASHER LOCK M12
70 049808 4 WASHER FLAT M12
71 077996 1 CAP ANTIFREEZE 5/8"ID X 1.2"LG
NOTES (UNLESS OTHERWISE SPECIFIED):
(1) SHEET METAL PARTS LISTED IN THE BOM TABLE ARE REPRESENTING GENERIC PARTS (NO COLOR)
MANUFACTURING: FOR CORRECT MATERIAL AND COLOR REFER TO XA BOM.
CUSTOMER: WHEN ORDERING REPLACEMENT PARTS ENTER BASE NUMBER (FIRST 6 DIGITS ONLY) IN THE SYSTEM FOR
CORRECT MATERIAL AND COLOR (FOR REFERENCE SEE GUIDELINE 0H7169).
1 0F7366 1 MUFFLER C1
2 0F7647 1 MUFFLER SADDLE
3 0F8095 1 PIPE EXHAUST OUTLET
4 0G3576 1 EXHAUST PIPE LOWER 1.6L
5 0E3257 4 SCREW HWHTF M6-1.0 X 16
6 0F7644 2 MUFFLER STRAP
7 0C6119 1 BOLT U 5/16-18 X 2-1/4
8 036434 3 BOLT U 5/16-18 X 2.09
9 036449 3 SADDLE 2 INCH
10 022129 6 WASHER LOCK M8-5/16
11 022259 6 NUT HEX 5/16-18 STEEL
12 038750 1 SCREW HHC M6-1.0 X 30 G8.8
13 0G3575 1 EXHAUST PIPE UPPER 1.6L SS
14 0F3794A 1 EXHAUST BLANKET 500MM LONG
15 022097 1 WASHER LOCK M6-1/4
16 049813 1 NUT HEX M6 X 1.0 G8 YEL CHR
17 022473 6 WASHER FLAT 1/4-M6 ZINC
EXPLODED VIEW: EV ALT COMMON PARTS
DRAWING #: 0J4228 GROUP A
ITEM PART# QTY. DESCRIPTION
REVISION: J-9826-C Page 2 of 2
DATE: 9/19/14
1 042558 1 KEY SQ 3/8 X 1 STEEL
2 0J6853A 1 SUPPORT LH ALT COVER
3 0J6853B 1 SUPPORT RH ALT COVER
4 020746 4 SCREW PPHM M5-0.8 X 8 ZINC
5 051787 4 SCREW HHC M4-0.7 X 16 C8.8
6 045771 4 NUT HEX M8-1.25 G8 CLEAR ZINC
7 0A5382A 1 BEARING CARRIER REAR LG PILOT
8 0G4196 1 FLYWHEEL ASSY 1.6L
9 0J6102 4 SCREW HHFC M10-1.5 X 20 C8.8
075591 1 HOLDER BRUSH - ASSEMBLY 10
0J6853C 1 COVER REAR 10" ALT 11
0G8827 4 STUD M8-1.25 475 LONG (30KW) 12
0G8827A 4 STUD M8-1.25 418 LONG (25KW)
072578 1 SPACER ROTOR SHAFT 13
053607 1 SCREW HHC M12-1.75 X 35 C8.8 14
0G2070A 1 PLATE SPACER 16GA 1.6L 15
023365 4 WASHER LOCK INT #8 16
051713 4 WASHER FLAT M5 17
051769 1 WASHER LOCK M12 18
0G0965B 1 PLATE FLEX 1.6L R12.7 19
049226 4 WASHER LOCK M5 20
0G0820B 1 HOUSING BLOWER 21
(1)22 0F3353 6 SCREW HHC M10-1.0 X 20 C10.9
0A8830 4 WASHER FLAT .34ID X .75OD 23
022129 4 WASHER LOCK M8-5/16 24
0G3787 6 WASHER FLAT .41ID .94OD .12THK 25
0G4452 1 BLOWER HOUSING SCREEN 26
0G2827 1 ASSY RTR 25KW 2P (2006) 27
0G3451C 1 RTR 102 30KD2 (2006) CPL CHI0"
0G2826 1 ASSY STR 102 25AD1 (2006) 28
0G3683 1 STR-102-25.0GD1 CPL(2006)
0G6573 1 STR-102-25.0-JD1 CPL
0G5909C 1 ASSY STR 102 30AD2 10" CHI
0G3684 1 STR-102-30.0GD2 CPL (2006)
0G6103 1 STR-102-30.0JD2
077043E 1 CONDUIT FLEX 1.0"ID (NOT SHOWN) 29
0C2454 6 SCREW HWHT M6-1 X 16 N WA Z/JS 30
0D8427 4 WASHER LOCK M10 RIBBED ZINC 31
NOTES (unless otherwise specified):
(1) APPLY LOCTITE 242 BEFORE THREADING SCREW INTO CRANKSHAFT.
EXPLODED VIEW: EV COOLING SYSTEM 1.5L
DRAWING #: 0J4592
GROUP C
ITEM PART# QTY. DESCRIPTION
REVISION: J-8330-C Page 2 of 2
DATE: 4/8/14
1 055934N 2 CLAMP STL/VNL 1.31 X .281 Z
2 0C8566 4 SCREW HHFC M6-1.0 X 20 G8.8
3 0G3573 1 GUARD FAN LH C1
4 0H1827 1 PROBE COOLANT LEVEL 3/8-18NPTF
5 0G3553 1 FAN COOL 450MM DIA 7 BLADE
6 0G3419 1 RADIATOR SUPPORT RH SIDE 1.6L
7 0E9837B 1 RADIATOR 1.6L G11
8 0J4545 1 HOSE REAR COOLANT 1.5L
9 099502 6 CLAMP HOSE #24 B1.06-2.00
10 022097 9 WASHER LOCK M6-1/4
11 039253 4 SCREW HHC M8-1.25 X 20 C8.8
12 080713 1 BRACKET COOLANT TANK
13 0E3257 2 SCREW HWHTF M6-1.0 X 16
14 0G3421 1 VENTURI 1.6L
15 076749 1 TANK COOLANT RECOVERY
16 0F9504 1 GROMMET 5/8"X 1 1/8"X 5/16"
17 0J4363 1 BRACKET COOLANT OVERFLOW TANK
18 046627 1 CAP RADIATOR 14PSI
(2)19 0G34330ST0R 1 BRKT FAN ALT ADAPTER 1.6L RAW
20 048031C 2 CLAMP HOSE BAND .50
21 022473 9 WASHER FLAT 1/4-M6 ZINC
22 0A2628 1 PULLEY - FAN 95 DIA
23 0J4717 1 TUBE ENGINE COOLANT 1.5L
24 0G4080 1 HOSE LOWER RADIATOR 1.6L
25 052250 1 TAPE FOAM 1X1
26 0C2454 25 SCREW HWHT M6-1 X 16 N WA Z/JS
27 022129 8 WASHER LOCK M8-5/16
(1)28 042907 4 SCREW HHC M8-1.25 X 16 C8.8
29 045771 4 NUT HEX M8-1.25 G8 CLEAR ZINC
30 0G3420 1 RADIATOR BLOCK-OFF
31 0G3418 1 RADIATOR SUPPORT LH SIDE 1.6L
32 0G4071 1 HOSE UPPER RADIATOR 1.6L
33 0G0568 1 ASSY FAN BEARING SUPPORT
34 027482 4 WASHER LOCK EXT 5/16 STL
35 0G3574 1 GUARD FAN RH C1
36 042568 4 SCREW HHC M6-1.0 X 20 C8.8
37 029032 1 HOSE 9/32 ID (46.5” LG)
38 029333A 10 TIE WRAP UL 7.4"X .19" BLK (NOT SHOWN)
39 032552 1 BARBED EL 90 5/16 X 1/8NPT
40 0C7649 2 CLAMP HOSE .38-.87
41 0C7997 1 HOSE COOL 5/16" SAE 20R3 (33”LG)
42 047411 1 SCREW HHC M6-1.0 X 16 C8.8
43 055934H 1 CLAMP STL/VNL .62 X .406 Z
NOTES (UNLESS OTHERWISE SPECIFIED):
(1) APPLY LOCTITE 242 TO I/N 28 & 36 BEFORE THREADING INTO I/N 33.
(2) SHEET METAL PARTS LISTED IN THE BOM TABLE ARE REPRESENTING GENERIC PARTS (NO COLOR)
MANUFACTURING: FOR CORRECT MATERIAL AND COLOR REFER TO XA BOM.
CUSTOMER: WHEN ORDERING REPLACEMENT PARTS ENTER BASE NUMBER (FIRST 6 DIGITS ONLY) IN THE SYSTEM FOR
CORRECT MATERIAL AND COLOR (FOR REFERENCE SEE GUIDELINE 0H7169).


Product specificaties

Merk: Generac
Categorie: Generator
Model: QT03015GNSX

Heb je hulp nodig?

Als je hulp nodig hebt met Generac QT03015GNSX stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Generator Generac

Handleiding Generator

Nieuwste handleidingen voor Generator