Gemini 7060 Handleiding
Gemini
Auto alarm
7060
Lees hieronder de 📖 handleiding in het Nederlandse voor Gemini 7060 (9 pagina's) in de categorie Auto alarm. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/9
7060
AC 2529 - REV. 00 / 06 / 01
No forest has been destroyed to
produce this 100% recycled paper.
by GEMINI TRADING S.r.l. Via Luigi Galvani 12 21020 Bodio Lomnago (VA) Italia
Tel. +39 0332 943211 - Fax +39 0332 948080
E-mail : info@gemini-alarm.com
7208
0682
INSTALLATION MANUAL
DESCRIPTION
GEMINI 7060
The system 7060 is an alarm unit that can be installed on vehicles with 12 volts battery (negative earth).
FUNCTIONS
- Remote controlled alarm unit with dynamic code.
- Blinker, universal central door locking control, electric windows and sunroof closure for selected vehicles
equipped with “Pack Comfort” system.
- Perimetric protection and outlet for additional modules.
- Controls for self-powered siren, additional siren (continuous or alternate sound) and horn.
- LED’s Memory.
- - Acoustic activation/de activation (through siren or horn).
- Remote controlled panic function and / or boot opening.
- Electric engine immobilisation.
- Alarm unit functions programmable through the transmitter.
The unit is equipped with two 2-channel transmitters (art. 7208E), frequency 433.92 Mhz.
USEFUL SUGGESTIONS FOR THE INSTALLATION
- Connect the positive and negative feeding wire of the alarm system to the battery.
- Connect always the alarm Green-Brown wire to the door pin switch.
- On catalysed vehicles the engine immobilisation must be carried out on the fuel pump and the starter motor.
- Avoid routing connection wires next to interference sources.
- The ultrasonic heads must be positioned at the top of each windscreen pillar and must be pointing at each
opposite diagonal corner away from the facia outlets.
WIRING CONNECTIONS
Disconnect the negative terminal of the battery and only re-connect after the installation is complete.
FUNCTION WIRE COLOR
Earth ðð BROWN
Battery positive terminal ðð RED
Engine immobilisation (max. 10 A) ðð 2 X GREY
Ignition live ðð YELLOW
Direction indicator lights ðð 2 x ORANGE
Door pin switch ðð GREEN-BROWN
Boot/bonnet pin switches ðð GREEN
Positive alarm armed ðð PINK
External sensors inlet ðð GREEN-BLACK
Self-powered siren control ðð BLUE
Common +/- siren or klaxon ðð BLACK
Additional siren or horn control ðð YELLOW-BLACK
Negative control boot opening ðð GREY-BLACK
Comfort ðð WHITE-BLACK
Central door locking ðð
YELLOW- -BLUE, RED BLUE, YELLOW-GREY,
RED-GREY, YELLOW- -BROWN, RED BROWN
Note: The wiring harness has 2 connectors: connect the 2-pin connector to the LED and the 4-pin
connector to an additional module (shock, ultrasonic or super-high frequency module).
"DIP SWITCHES PROGRAMMING TABLE"
1 OFF Comfort POSITIVE
2 ON Comfort NEGATIVE
2 OFF Automatic arming OFF
2 ON Automatic arming ON
3 OFF Self-learning of a new code OFF (normal use)
3 ON Self-learning of a new code ON
4 OFF Closure short * period
4 ON Closure 6 seconds
* THE SHORT TIME IS SET FROM THE PROGRAMMING WITH THE TWO-CHANNELS TRANSMITTER
BETWEEN 0,5 SECONDS AND 1 SECOND.
ATTENTION : SET THE DIP SWITCHES BEVOR FEEDING THE 7060 UNIT.
TABLE OF PROGRAMMABLE FUNCTIONS THROUGH THE TWO-CHANNELS TRANSMITTER.
ACTIONS
ALARM CONDITION VISIBLE
ACTIONS
LED FLASHING AND
SELECTED FUNCTIONS
ALTERNATIVE
ACTIONS
POWER OFF Alarm OFF - - -
Turn the ignition
key to ON
Alarm OFF
-
-
-
FEED THE UNIT
7060
Alarm ON
-
-
-
Press on the
transmitter 1 button
within 10 seconds
Access to the Set-up 1 function:
Supplementary siren One blinker
flashing
One flashing = continuous
Two flashing = intermittent
Press on the
transmitter 1 button
Access to the Set-up 2 function:
acoustic signalling with
supplementary siren 725
Two blinker
flashing
One flashing = de-activated
Two flashing = activated
Press on the
transmitter 1 button
Access to the Set-up 3 function:
Panic and boot opening through
the transmitter
Three
blinker
flashing
One flashing = Panic and
additional siren
Two flashing = Boot opening
Press on the
transmitter 1 button
Access to the Set-up 4 function:
boot opening while alarm armed
(Panic excluded)
Four blinker
flashing
One flashing =
While alarm disarmed
Two flashing =
For both functions
Press on the
transmitter 1 button
Access to the Set-up 5 function:
vehicle check while arming the
system
Five blinker
flashing
One flashing = de-activated
Two flashing = activated
Press on the
transmitter 1 button
Access to the Set-up 6 function:
closure control period Six blinker
flashing
One flashing = 0,5 seconds
Two flashing = 1 seconds
Press on the
transmitter 1 button
Access to the Set-up 7 function:
Automatic arming with door
closure
Seven
blinker
flashing
One flashing = activated
Two flashing = de-activated
Press on the
transmitter 1 button Access to the Set-up 8 function:
Comfort
Eight
blinker
flashing
One flashing = while closing
Two flashing = after the
closure
Press on the
transmitter
button N. 2 to
change the
selected option.
De-activate the
+15 to memorise
the selected
options and to
exit from User
set-up.
Turn the ignition
key to OFF Set-up exit, normal working
of the alarm - - -
Recapitulatory table of the programmable functions through the two -channels transmitter.
Function Manufacturer function Programmable function
1 Additional siren outlet Continuous sound Alternate sound
2 Acoustic signalling De-activated Activated
3 Boot opening with alarm disarmed De-activated Activated
4 Boot opening with alarm armed
With alarm disarmed if the 3
functions has been activated Both functions
(Panic excluded)
5 Vehicle’s check De-activated Activated
6 Central door locking short period 0,5 seconds 1 second
7 Automatic arming Activated De-activated
8 Comfort While closing the doors After the blinker flashing
WORKING DESCRIPTION
- ALARM ARMING: press on the transmitter’s button N. 1. One pulse of the direction indicator lights signals
the arming.
- EXCLUSION OF THE VOLUMETRIC SENSOR, EXTERNAL SENSORS AND COMFORT CONTROL
AFTER THE ALARM ARMING: while alarm armed (even if the boot opening function with alarm armed is
activated), during the inhibit time (Led lightning fix) press on the transmitter 2 button. The exclusion is
signalled by one pulse of the direction indicator lights, the comfort function and the sensors are excluded.
This function de-activates at the first arming of the alarm.
- ALARM DISARMING: press on the transmitter’s button N. 1.
The disarming is signalled through 3 pulses of the direction indicator lights or 5 pulses if an alarm condition
has occurred.
SPECIAL FUNCTIONS
SELF-LEARNING OF THE CODE OF A NEW TRANS MITTER.
The self-learning of a new transmitter can be obtained with two different ways:
1. While alarm disarmed set the dip switch N.3 to ON and turn the ignition key to ON. The Led and the direction
indicator lights activate. Turning the ignition key to OFF the Led and the direction indicator lights switch off.
Press on the new transmitter button N. 1 within 8 seconds.
For each new code it is necessary to turn the ignition key to ON for one second and then to OFF.
At the end of the self-learning operation set the dip switch N.3 to OFF.
2. While alarm disarmed, open the driver’s door, turn the ignition key to ON and press on the coded transmitter
button N. 2. The Led and the direction indicator lights activate. Turning the ignition key to OFF the Led and
the direction indicator lights switch off. Press on the new transmitter’ s button N. 2 within 10 seconds.
For each new code it is necessary to turn the ignition key to ON for one second and then to OFF.
At the end of the self-learning operation, after 10 seconds the system works normally.
NOTE: the system is supplied with a maximum number of 3 transmitters.
AUTOMATIC ARMING
To obtain this function set the dip switch N. 2 to ON. 60 seconds after the disarming of the alarm, if the doors
and the boot are not opened and the ignition key is not turned to ON, the system will arm with or without closing
the vehicles doors (according to setting of the set-up 7 function).
REMOTE CONTROLLED BOOT OPENING.
The alarm unit 7060 allows opening the vehicle boot if the control is electric to negative. To obtain this function
select the set-up 3 function and press on the transmitter button N. 2 with the alarm disarmed.
If the boot opening is carried out pressing on the transmitter 2 button with the alarm armed (after selecting the
set-up 4 function), the panic function will de-activate and all the inlets inhibit for 60 seconds. If the boot is not
closed within this delay time the alarm will trigger. The opening of the boot through the transmitter is signalled
by one pulse of the direction indicator lights.
PANIC FUNCTION
To obtain this function with the alarm armed after the neutral time, press on the transmitter button N. 2 (if the 4
function- - boot opening with alarm armed is de activated). The siren, the klaxon and the direction indicator lights
activate. To de-activate this function within the 10 seconds of the alarm cycle, press on the transmitter button
N. 2.
LEDS MEMORY.
While disarming the alarm, turn the ignition key to ON to check if an attempted break-in has occurred.
Following the Led flashing it is possible to know the alarm triggering’s cause. The signalisation is repeated for
5 times.
Signalling LED Alarm triggering Alarm cycle
¬¬ ¬¬l Door and boot/bonnet pin switches. 10
¬¬¬ ¬¬¬l Ignition live Unlimited
¬¬¬¬l¬¬¬¬ External sensors 10
l LED OFF (2 seconds) ¬ LED ON (1 second)
Each alarm cycle is 30 seconds
The inhibit time is 30 seconds for all alarm triggering’s cause.
TRANSMITTERS BATTERY DISCHARGING
The discharging of the battery is signalled through the LED of the
transmitter. If the LED flashes while pressing one of the transmitter’s
buttons it is necessary to replace the batteries.
BATTERIES: CR1616
Note: put the batteries in the appropriate container.
TECHNICAL DATA
Power supply 10.5-14.5 V dc.
Working temperature -40° C + 85°C
Max. Current drawn alarm OFF 15 mA (with self-powered siren connected)
Transmitters frequency 433.92 MHz
Direction indicator lights relay contact capability 8A dc
Engine immobilisation relay contact capability 8A dc
Outlet horn relay contact capability 8A dc
Central door locking relay contact capability 8A dc
GEMINI 7147
DESCRIPTION.
GEMINI 7147 is 2 wires, high power electronic siren designed to be installed quickly and simply in the engine compartment.
WIRING CONNECTIONS (for the installer)
Disconnect the negative terminal of the battery and only re-connect after the installation is complete.
WIRE COLOUR FUNCTION
RED é Battery positive terminal (12V)
BLACK é To the alarm YELLOW -BLACK wire.
NOTE: connect the BLACK wire of the unit to earth.
INSTALLATION.
Install the siren in the engine compartment using the bracket and the screws supplied with the kit. Install the siren away from
areas of intense heat and turn to low the siren ear trumpet to avoid water infiltration.
Protect the wires from water and humidity and to avoid any damaging do not steam clean directly to the siren.
Product specificaties
| Merk: | Gemini |
| Categorie: | Auto alarm |
| Model: | 7060 |
Heb je hulp nodig?
Als je hulp nodig hebt met Gemini 7060 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Auto alarm Gemini
15 Januari 2023
13 Juni 2023
12 Juni 2023
9 Juni 2023
15 Januari 2023
15 Januari 2023
7 Juni 2023
15 Januari 2023
4 Juni 2023
3 Juni 2023
Handleiding Auto alarm
- Auto alarm HP
- Auto alarm Audiovox
- Auto alarm Eufab
- Auto alarm GT
- Auto alarm Spy
- Auto alarm Technaxx
- Auto alarm Viper
- Auto alarm Waeco
- Auto alarm Jablotron
- Auto alarm Olympia
- Auto alarm Cobra
- Auto alarm Clifford
Nieuwste handleidingen voor Auto alarm
7 Februari 2024
7 Februari 2024
7 Februari 2024
6 September 2023
30 December 2022
20 Maart 2023
25 April 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023