GE JV376VWW Handleiding

GE Afzuigkap JV376VWW

Lees hieronder de 📖 handleiding in het Nederlandse voor GE JV376VWW (4 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Use and Care & Installation Guide

30” Vented Range Hood

Model: JV376

Write Down the Model and Serial Numbers.

The Model and Serial Numbers are on a label on the

back wall of the hood and on the Consumer Product

Ownership Registration Card that came with your hood.

Before sending in this card, please write these numbers here:

Model Number

Serial Number

IMPORTANT SAFETY INSTRUCTIONS

Read and save these instructions.

WARNING—TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address or telephone number

listed in the warranty.

B. Before servicing or cleaning unit, switch power

off at service panel and lock service to prevent

power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such

as a tag, to the service panel.

C. Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

D. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel-

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer’s guidelines and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

E. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

F. Ducted fans must always be vented to the outdoors.

G. To reduce the risk of fire, use only metal ductwork.

H. This unit must be grounded.

WARNING—TO REDUCE THE RISK OF A

RANGE TOP GREASE FIRE:

A. Keep fan, filters and grease-laden surfaces clean.

B. Always turn hood ON when cooking at high heat.

C. Don’t leave range unattended when cooking.

D. Use high settings on range only when necessary.

Heat oil slowly on low to medium setting.

E. Always use cookware and utensils appropriate for the

type and amount of food being prepared.

• When flaming foods under the hood, turn the fan on.

WARNING—TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING:

A. SMOTHER FLAMES with a close-fitting lid, cookie

sheet, or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do

not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN—You may be

burned.

C. DO NOT USE WATER, including wet dishcloths or

towels—a violent steam explosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher,

and you already know how to operate it.

2. The fire is small and contained in the area where

it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

*Based on “Kitchen Firesafety Tips” published by NFPA.

CAUTION—For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

If You Need Service…

• Do not attempt to repair or replace any part of your

hood unless it is specifically recommended in this

guide. All other servicing should be referred to a

qualified technician.

SAVE THESE INSTRUCTIONS

GE Appliances

164D2966P166-2

Venting

This hood must be vented vertically through

upper cabinets or horizontally through an outside

wall. Ductwork is not included.

Improper duct sizing or restrictive roof caps

reduce air moving capacity and will not provide

enough ventilation for an indoor electric grill.

Indoor electric grills produce more smoke than

normal cooking and require at least 410 CFM to

provide adequate ventilation.

Follow the guidelines for proper duct sizing in the

ducting charts. NOTE: The venting system must

exhaust to the outside.

Cabinet Height

For most efficient operation, the top of the hood should

be approximately 66 (167.6 cm) from the floor.″

Tools Required:

• Drill; 11⁄4″wood bit. • Pliers.

• Flat blade screwdriver. • Pencil, ruler and level.

• Saber saw or keyhole saw.

• Caulking, metal snips, duct tape, ducts (with

elbow and transition, if necessary) and wall cap

or roof caps, as required.

INSTALLATION INSTRUCTIONS

Installing the Range Hood

Determine which direction the vent will be

installed (top or rear).

1. Remove filters and motor/light cover (3 screws).

2. Remove the blower motor by removing the

“packing screw” and the clip on the retainer bar.

Discard the clip and screw.

Unplug the motor from the junction box.

Snap the blower retainer

bar toward the rear of

the hood to release the

blower. Remove the

blower.

3. Remove the junction

box cover.

Remove the selected wiring knockout and duct

knockout from the top or rear of the hood. Use a

at blade screwdriver to cut the tabs.

IMPORTANT: OBSERVE ALL GOVERNING

CODES AND ORDINANCES.

SAVE THESE INSTRUCTIONS FOR THE

LOCAL ELECTRICAL INSPECTOR’S USE.

WARNING: Disconnect power before servicing or cleaning the unit.

Blower Control Care of Filter Motor

The speed control can be adjusted

from OFF to high speed. At the

highest setting, the blower exhausts

410 CFM. It takes about 15 seconds

for the blower to reach high speed..

For most eective removal of smoke

and odors, turn the fan on at the

beginning of cooking and allow it to

run until smoke and odors are

removed from the room.

For greatest eciency the aluminum

lter should be cleaned periodically.

To remove the lter, pull the tab to

the side and then down. Soak it in hot

water and detergent. Rinse and dry

thoroughly before replacing.

Lights Care of Exterior Surfaces

This hood has two lights. Do not use

bulbs larger than 75 watts. There are

two light levels. To change light

bulbs, rst remove the lters. It is not

necessary to remove the blower cover.

Use a mild detergent to clean the hood.

DO NOT use abrasive cleansers.

Top Vent

Knockout

Snap

lock blower

retainer bar

When the control is not set on high

and if the motor seems to be

operating at high speed or if

ventilation seems inadequate, check

the following:

1. Knockouts not removed from hood.

2. Blower installed for vertical

discharge instead of horizontal

discharge or vice versa.

3. Damper blade not opening.

4. Reduced airflow because the duct is

too small or the length is too long.

5. The duct is blocked.

6. Undersized or restrictive wall or

roof cap.

HORIZONTAL VENTING

(If the wall cap has a damper, do not install the

damper blade on the hood.)

Attach the damper with the small sheet metal

screws (#8 x 1/4 ).″

Check the damper

for free operation.

Open the damper

blade to

approximately 80

degrees.

Position the blower for horizontal discharge. The

air ow arrow on the blower should point to the

rear vent opening.

When the blower is in position, snap the blower

retainer bar toward the front into the indent.

Reattach the plug into the junction box.

8. Lift the hood into position and feed the house

wiring through the wiring knockout.

Slide the hood back against the wall.

Tighten the mounting screws. Be sure the screw

heads are in the narrow neck of the keyhole slot.

9. Complete the electrical wiring in the wiring

box according to National Electrical Code and

local codes.

NOTE: This hood must be permanently

grounded.

10. Replace the junction box cover and blower

assembly.

Reattach the plug into the junction box.

Install light bulbs (not supplied with the hood).

Reattach bottom motor/light cover and lters.

11. Installation is complete. Turn on the power.

VERTICAL VENTING

(If the roof cap has a damper, do not install the

damper blade on the hood.)

Attach the damper with the small sheet metal

screws (#8 x 1/4 ).″

Check the damper

for free operation.

Open the damper

blade to

approximately 80

degrees.

Position the blower for vertical discharge. The

air ow arrow on the blower should point up

towards the vent opening.

When the blower is in position, snap the blower

retainer bar toward the front into the indent.

Reattach the plug into the junction box.

Blower discharge

Air ow arrow

This surface

to rear

3″

5″

Damper blade

to front

This surface to top

Blower

discharge

3″

5″

Air ow arrow

Damper

blade to top

Damper

4. Use the hood as a template. Mark the

locations on the cabinet or wall for ductwork,

electrical wiring and keyhole screw slots.

Cut holes at marked locations for duct and

electrical wiring. For the vertical duct, cut out 3/4″

extra toward the front of the cabinet for movement

of the duct when installing the hood.

5. Run the electrical wires through the wall or

cabinet according to National Electrical Code

and applicable local codes.

NOTE: DO NOT turn the power on until

installation is complete.

6. Drive the screw partway

into the center of the

narrow neck of the keyhole

slots marked on the

cabinets.

7. Follow the directions for vertical or

horizontal venting.

NOTE: If the venting installation is NOT

correct, the blower will run at maximum RPM

regardless of the speed control setting.

When installing the blower housing, be

sure wires cannot contact the blower wheel.

Keyhole slot

in canopy

Screw

(supplied)

Damper

Product specificaties

Merk:	GE
Categorie:	Afzuigkap
Model:	JV376VWW

Heb je hulp nodig?

Als je hulp nodig hebt met GE JV376VWW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Afzuigkap GE

GE UVC9480SLSS Handleiding

15 November 2024

GE UVD6301DPBB Handleiding

22 Maart 2024

GE UVD6361DPBB Handleiding

22 Maart 2024

GE UVI7361SWSS Handleiding

22 Maart 2024

GE PV970NSS Profile Handleiding

6 December 2023

GE Profile PVX7300SJSS Handleiding

6 December 2023

GE CV966TSS Cafe Handleiding

7 Oktober 2023

GE Cafe CV966TSS Handleiding

7 Oktober 2023

GE Cafe CV936MSS Handleiding

7 Oktober 2023

GE CV936MSS Cafe Handleiding

7 Oktober 2023

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap

Miele DA 6520 D Handleiding

21 November 2024

Miele DA 420-4 Handleiding

21 November 2024

Miele DA 2906 EXT Handleiding

21 November 2024

Miele DA 2660 Handleiding

21 November 2024

XO R230W Handleiding

21 November 2024

Ilve AGK90 Handleiding

20 November 2024

Ilve AGQ90 Handleiding

20 November 2024

Ilve AGQ60 Handleiding

20 November 2024

Ilve AGQ120 Handleiding

20 November 2024

Ilve AGK120 Handleiding

20 November 2024