GE JD750DFBB Handleiding

GE Fornuis JD750DFBB

Lees hieronder de πŸ“– handleiding in het Nederlandse voor GE JD750DFBB (24 pagina's) in de categorie Fornuis. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24
1
31-10829-2 01-14 GE
BEFORE YOU BEGIN
Read these in struc tions care ful ly and completely.
β€’ IMPORTANT Β³ Save these instructions for
local in spec tor’s use.
β€’ IMPORTANT Β³Observe all governing
codes and ordinances.
β€’ Note to Installer – Be sure to leave these
instructions with the consumer.
β€’ Note to Consumer – Keep these instructions for
future reference.
β€’ Skill level – Installation of this appliance requires a
qualified installer or electrician.
β€’ Proper installation is the responsibility of the installer.
β€’ Product failure due to improper installation is NOT
covered under the warranty.
30” Electric
Drop-In Ranges
Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com.
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca.
β€’ ATTENTION INSTALLER: All electric drop-in ranges must be hard wired (direct wired) into an
approved junction box. A plug and receptacle is NOT per mit ted on these products
.
FOR YOUR SAFETY
WARNING Before beginning the installation, switch power off at the service panel and lock the
service disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
WARNING The information in this manual must be followed to minimize the risk of fire, electric shock,
or to prevent property damage, personal injury or loss of life.
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2” Conduit
TOOLS YOU MAY NEED
1/8” Drill Bit and Electric Drill Phillips Screwdriver
Level Flathead Screwdriver
Tape Measure 1/4” Nut Driver
Straight edge or Square Hammer
Hand or Saber Saw Pencil
Safety Glasses
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed
and engaged.
Ensure the anti-tip bracket is re-engaged when the range
is moved.
Do not operate the range without the anti-tip bracket in
place and engaged.
Failure to follow these instructions can result in death or
serious burns to children or adults.
Tip-Over Hazard
WARNING
Oven
Anti-Tip Bracket
Countertop or
Wood Block
Rear
Wall
2
Installation Instructions
Failure to remove packaging materials could result in damage to the appliance. Remove all packing parts from
oven, racks, and heating elements. Remove protective film and labels on the outer door and control panel.
Also remove plastic on trims and panel and all tape around the oven. Open oven door and remove literature
pack and oven racks. Remove the bottom trim from the side of the oven. It will be installed at the end of the
installation process. The trim is wrapped separately in a plastic bag which will also contain the 4 screws to
secure the bottom trim and the 2 shoulder screws used to secure the product to the cabinet.
1 REMOVE PACKAGING MATERIALS
Allow 30” minimum clearance
between surface units and bottom
of unprotected wood or metal
cabinet. Allow a 24” minimum
when bottom of wood or metal is
protected by no less than 1/4” thick
flame retardant millboard covered
with not less than No 28 MSG sheet
metal (.015”), .015” thick stainless
steel, .024” aluminum or .020”
copper.
NOTE: Drop-In Ranges are designed to hang
from the countertop only. Do not install on a
platform or sup port rails.
2 PREPARING THE OPENING (FOR INDOOR USE ONLY)
3
Installation Instructions
2 PREPARING THE OPENING (Continued)
The Standard Installation of this Drop-In Range is to hang
by the countertop on the side metal flang es under glass
cooktop. This Range must not be installed on a base or
sub structure (2”x 4” support).
If the construction of your cabinet cannot provide a
1/4” flat area at the back of the countertop opening,
consider changing the countertop to accommodate this
dimension. If the area is not flat, excess tension may
be applied to the glass cooktop, causing breakage and
voiding the warranty.
β€’ Countertop thickness 1-1/4” min. is required to support the product. Braces must be installed between the
underside of the countertop and the cabinet if required to obtain 1-1/4” minimum thickness (each side).
β€’ Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to 200Β° F
(93.3Β° C) generated by the oven.
β€’ This appliance has been approved for 0” spacing to adjacent surfaces above the cooktop. However, a 6”
minimum spacing to surfaces less than 15” above the cooktop and adjacent cabinet is recommended to
reduce exposure to steam, grease splatter and heat.
β€’ Locate the wiring junction box at the rear of the cutout. The dimension from the top of the wiring junction
box to the countertop must be a minimum of 28-1/2”. The box must not extend more than 3” off the plane
of the wall. The junction box must be located where it will allow considerable slack in the range conduit, so
that the range can be pulled out for service if necessary.
Wall
1/4” min. flat
23-3/16”
9/16” min.
flat
9/16” min.
flat
29-15/16”– 30-1/16”
smooth cut
25”
typically 1/4”
R
Flat
area
Countertop
Range support


Product specificaties

Merk: GE
Categorie: Fornuis
Model: JD750DFBB

Heb je hulp nodig?

Als je hulp nodig hebt met GE JD750DFBB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Fornuis GE

Handleiding Fornuis

Nieuwste handleidingen voor Fornuis