GE GFA28KITN Handleiding

GE Wasmachine GFA28KITN

Lees hieronder de 📖 handleiding in het Nederlandse voor GE GFA28KITN (12 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
If you have any questions, call GE Appliances at 800.432.2737 or visit our Website at: GEAppliances.com
In Canada, call 800.561.3344 or visit www.GEAppliances.ca
Stack Bracket Kit
GFA28KITN
Installation
Instructions
31-3000211 09-19 GEA
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions for
local electrical inspector’s use.
IMPORTANT Observe all governing
codes and ordinances.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions for
future reference.
Installation be performed by a qualified must
installer.
Proper installation is the responsibility of the installer.
MINIMUM CLEARANCE OTHER
THAN ALCOVE OR CLOSET
INSTALLATION
Minimum clearance to combustible surfaces and for
air opening are: 0” both sides , 0” rear and 0” top.*
The rear of the dryer should face a wall.
Consideration must be given to provide adequate
clearance for installation and service.
Remove the packaging.
Flatten the product carton to use as a pad to lay
the dryer down on its back or side. Continue using
the carton to protect the finished floor in front of the
installation location.
REQUIREMENTS FOR ALCOVE OR
CLOSET INSTALLATION
The dryer MUST be vented to the outdoors.
Minimum clearance between dryer cabinet and
adjacent walls or other surfaces is:
0” either side*
0” front
0” rear
0” top
The rear of the dryer should face a wall.
Consideration must be given to provide adequate
clearance for installation and service.
Closet doors must be louvered or otherwise ventilated
and have at least 60 square inches of open area. If the
closet contains both a washer and a dryer, doors must
contain a minimum of 120 square inches of open area.
NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT
THE REAR OF THE DRYER, THE CONFIGURATION
OF THE DUCTING MAY REQUIRE GREATER
CLEARANCE.
Gas Dryers Only:
No other fuel burning appliance shall be installed in
the same closet as a gas dryer.
The dryer must be disconnected from the gas
supply piping during pressure testing at pressures
greater than 1/2 psi (3.5 kPa).
A 1/8 inch NPT minimum plugged tapping,
accessible for test gauge connection, must be
installed immediately upstream of the gas supply
connection to the dryer.
Keep flammable materials and vapors, such as
gasoline,
away from dryer.
Place dryer at least 18” (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
- Explosion Hazard
WARNING
Mobile Home or Manufactured Home Installation
Stacking of a gas dryer is not permitted in a mobile
home or manufactured home.
Use two or more people to install dryer.
Avoid tipping and rupture of utility services.
Dryer must be securely attached to the washer.
DO NOT place the washer on top of the dryer.
Failure to do so may result in serious injury,
death, or property damage.
WARNING - Excessive Weight
Hazard
Disconnect power before
installing. Failure to do so could
result in serious injury or death.
WARNING
INSTALLATION PREPARATION
Stack dryer only on washer. Do not stack washer on
dryer, washer on washer or dryer on dryer.
Do not modify this installation kit. Any modification will
void the product Warranty.
*For improved performance, a 1/2clearance is suggested on either side.
2
Installation Instructions
TOOLS YOU WILL NEED
Ŷ Phillips screwdriver Ŷ Pliers
Ŷ Gloves
Ŷ Open-ended wrench
Ŷ Bracket 32
(2)
Ŷ Spacer (2) Ŷ #8 1/2" Screws
(16)
CONTENTS
Ŷ Level
Ŷ Bracket 34
(2)
REMOVE THE DRYER LEVELING
LEGS
A. Carefully lay the dryer on its back or side. Use the
packing material so you don’t scratch the finish on
the dryer.
1
B. Use an open-end wrench or pliers to remove the
dryer leveling legs. Retain the leveling legs NOTE:
for future use.
Back out and
remove all 4
leveling legs
INSTALL SPACERS TO THE
DRYER BOTTOM
Locate a spacer on the bottom side with its holes over
the leveling leg holes. Attach spacer using 2 screws.
Attach the second spacer on the other bottom side
using 2 screws. The arrows on the spacers NOTE:
should point to the outside.
2
Attach spacer using 2 screws
Attach spacer using 2 screws
Front Back
Make sure the arrows on the spacer point to the outside.
Make sure the arrows on the spacer point to the outside.
3
Installation Instructions
PREPARE THE WASHER AND
DRYER
A. Place the washer in the approximate final
installation location.
B. Make sure the washer is level. Refer to the washer
Installation Instructions for details.
C. Upright the dryer.
D. Reverse the washer and dryer door swings, if
desired, before stacking the dryer on the washer.
See the washer and dryer Installation Instructions
for details.
4
INSTALL THE APPROPRIATE
BRACKETS TO THE WASHER
Select the appropriate brackets for your model sizes.
Using the outside holes in the bracket, attach it to the
top left corner of the washer back using 4 screws.
Repeat on the top right corner of the washer back.
3
Washer Depth Dryer Depth Bracket Number
32" 32" 32
34" 32" 34
32 Brackets for 32" Washer & Dryer Combinations:
Attach
brackets to
washer using
4 screws on
each side
34 Brackets for 34" Washer & 32" Dryer Combinations:
Attach
brackets to
washer using
4 screws on
each side
OR
Install brackets flush at
washers edges
Do not install brackets
overhanging washers edges
Install brackets flush at
washers edges
Do not install brackets
overhanging washers edges


Product specificaties

Merk: GE
Categorie: Wasmachine
Model: GFA28KITN

Heb je hulp nodig?

Als je hulp nodig hebt met GE GFA28KITN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wasmachine GE

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine