Frigidaire MWTKP27KF Handleiding

Frigidaire Magnetron MWTKP27KF

Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire MWTKP27KF (4 pagina's) in de categorie Magnetron. Deze handleiding was nuttig voor 66 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Installation

Instructions

Built-in Trim Kit

MWTKP27KF,MWTK27KF,MWTK27KB,MWTK27KW

MWTKP30KF,MWTK30KF,MWTK30KB,MWTK30KW

BEFORE YOU BEGIN

• IMPORTANT – Save these instructions

for local inspector's use.

• IMPORTANT – Observe all governing

codes and coordinates.

• Note to Installer – Be sure to leave

these instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• - Skill level Installation of this appliance

requires basic mechanical and electrical

skills

Read these instructions completely and carefully.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

• Unplug the microwave oven before

attempting installation of this kit.

• Because the kit includes metal parts, caution

should be used in handling and installation to

avoid the possibility of injury.

• Do not remove permanently affixed labels,

warnings, or plates from the product. This

may void the warranty.

FOR YOUR SAFETY:

WARNING – Before beginning the installation,

switch power off at service panel and lock the

service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to

the service panel.

IMPORTANT - PLEASE READ

AND FOLLOW

THIS BUILT-IN KIT IS DESIGNED FOR USE

ONLY WITH ELECTROLUX MICROWAVE

OVENS SPECIFYING BUILT- IN KIT

MWTK(P)27K OR MWTK(P)30K ON THE RATING

LABEL ON THE LEFT SIDE WALL OF THE

MICROWAVE OVEN CAVITY.

QUESTIONS?

For customers in the United States call: 1-800-944 9044-

For customers in Canada call: 1-800-265-8352 (English)

1- - -800 668 4606 ext.8199 (French)

Visit our Website at: www.frigidaire.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

PN316495084

SEPT 2009

Installation Instructions

PARTS INCLUDED IN THE KIT

1. Front Frame Assembly - QTY 1

2. Exhaust Duct Assembly - QTY 1

3. Screw A - QTY 2

4. Screw B - QTY 4

CHOOSING A LOCATION FOR

YOUR MICROWAVE OVEN IF

BUILT-IN

Built-In Trim Kit allows for the installation of microwaves

listed below to be built into a cabinet or wall by itself or

over an electric wall oven*.

Microwave Models:

FGM0205KB PLMBZ209GC CGM0205KB

FGM0205KF GLMB209DS CGM0205KF

FGM0205KW GLMB209DB CGM0205KW

FPM0209KF CPM0209KF

See Illustration 1 for proper location when building in

above a wall oven. Carefully follow both the wall oven

installation instructions and Electrolux’s Built-in Kit

instructions. If building over a wall oven, be sure the

clearance between the wall oven and the microwave

oven is a minimum of 3 inches.

*NOTE: -Trim Kit and microwave can only be built in

over an electric self clean or non self- -clean

single cavity wall oven.

CABINET OR WALL CUT OUT

Cutout Dimensions

Height (A)

Minimum

Maximum

16 3 4/” (42.5 cm)

17” (43.2 cm)

Width (B)

Minimum

Maximum

24 3/4” (62.9 cm)

2 ) 5” (63.5 cm

Depth (C)

Minimum

20” (50.8 cm)

Illustration 1

Screw A

Screw B

Front Frame Assembly

Exhaust Dust Assembly

Installation Instructions

Illustration 2

ELECTRICAL OUTLET LOCATION

Outlet should NOT be in the shaded area as indicated

on Illustration 2

NOTE 1:

If the Depth (C) dimension is greater than 21” (53.3 cm),

the outlet location may be in any area on the rear wall.

NOTE 2:

The floor of the opening should be constructed of

plywood strong enough to support the weight of the

oven and floor load (approximately 100 pounds). The

floor should be level for proper operation of the oven. Be

sure to check the local building code as it may require

that the opening be enclosed with side, ceiling and rear

partition. The proper functioning of the oven does not

require the enclosure.

Illustration 3

EXHAUST DUCT ASSEMBLY

1. Place the Exhaust Duct in the opening. When

the Exhaust Duct Assembly is in the opening

correctly, the flanges will be tightly against the

lower edge of the opening. See Illustration 3.

2. Secure the Exhaust Duct Assembly with the

two screws A.

IMPORTANT: Secure screws in outer hole.

Screw A

Exhaust Dust

Assembly

Flanges

Product specificaties

Merk:	Frigidaire
Categorie:	Magnetron
Model:	MWTKP27KF
Kleur van het product:	Grey, Stainless steel
Gewicht:	3628 g
Breedte:	684 mm
Diepte:	254 mm
Hoogte:	460 mm
Gewicht verpakking:	4989 g
Productafmeting:	XL
Aantal per verpakking:	1 stuk(s)
Type product:	Magnetron inbouwset