Frigidaire FGCD2444S Handleiding

Frigidaire Vaatwasser FGCD2444S

Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire FGCD2444S (2 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
16 3/ ”8
Before You Begin
Read all instructions before installing dishwasher.
For your safety, please read and observe all safety
instructions. This guide will help you anticipate drain, water, and
electrical connections, and help you select the best location for the
dishwasher.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Failure to follow this warning can result in serious
injury.
Figure 4
4. Cut water access hole in shaded area in Figure 2.
5. Route water supply line into installation area.
IMPORTANT: Incoming hot water temperature should be at
least 120°F (49°C). Water pressure should be between
20–120 psi.
Drain
1. Review Figures 5, 6 and 7 to see the different ways to connect
dishwasher to drain system. Choose method that best suits
your need.
2. If you connect to a sink drain, entry will need to be above
trap. A “Y” branch tailpiece and connector kit, not included, will
make this method easier and includes all needed fittings and
instructions. See Figure 5.
5. Before cutting drain hose access, check both sides of selected
area to avoid interference. Cut a 2” diameter hole in shaded
area shown in Figure 2.
6. If the cabinet wall is wood, sand edges of hole until smooth and
rounded. If cabinet wall is metal, cover all sharp edges with
electrical or duct tape to avoid cutting drain hose.
Installation Tips 1
Tools and Materials Needed for
Installation
• Drill, Electric
• Driver, Socket 5/32”, 1/4” , 5/16”
• Flaring Tool / Tube Cutter (for copper tubing)
• Flashlight
• Gloves
• Level
• Pipe Joint Compound (for iron pipe plumbing) or
Pipe Thread Tape (for sealing threads)
• Pliers
• Safety Glasses
• Saw, Keyhole or 1/2
”, 11/2”
to 2” Hole Cutters
• Screw Drivers, Slotted and #2 Phillips (magnetic tip
preferred)
• Tape, Electrical or Duct
• Tape, Measuring
• Wire Stripper or Utility Knife
• Wrench, Hex-end
• Wrenches, 2 Adjustable (for copper tubing)
or 2 Pipe wrenches (for iron pipe plumbing)
Electric Shock Hazard
Electrical, water, and drain lines must be confined
to shaded areas in Figure 2.
Electric conductors, water, and drain could be
damaged.
Failure to follow these instructions could result in
fire or electric shock.
NOTE: If dishwasher is installed at end of a cabinet line, sides
and back must be fully enclosed.
NOTE: You can order a Cabinet Seal Kit (Kit # 154528701) by
contacting your dealer or parts supplier. This kit provides a
seal between the unit and cabinets once installation is
complete.
IMPORTANT: Do not cross drain, water, and electrical lines in
front of dishwasher motor or frame.
4
Connections For Electrical,
Water, and Drain
Right Side
Front
Left Side
Door in
open position
Locating the Connections
1. Review dimensions in Figure 3 to locate dishwasher’s drain,
water, and electrical connections.
2. All connections must be made in shaded area in Figure 2.
25 24 49 1/ ”422 1/ ”2
3 31/2”
Min.
From rear to
center of water
inlet valve.
3 3/4”
From floor to
water inlet
valve.
Floor Line
Figure 3
Junction Box
(not visible)
17 3/ ”4
From rear to
junction box.
3. Locate water inlet valve behind kickplate on bottom left
underside of unit. The valve has a 3/8” NPT or 3/4” hose thread
fitting. Note: If using 3/4” hose thread fitting skip steps 4 and 5.
4. Wrap 90° elbow (not included) with pipe thread tape (or apply
joint compound) and thread it into water inlet valve.
5. Tighten elbow with a wrench, leaving elbow pointing toward
rear of unit. To prevent bending of bracket or breaking of valve,
avoid overtightening.
6. If using 3/4” hose thread fitting, do not use teflon tape, tighten
elbow. Do not over tighten.
1. Remove two (2) screws at front of the kickplate assembly using
a #2 Phillips screw driver.
2. Tilt and pull forward to remove. See Figure 1.
NOTE: It is not necessary to remove the outer door for installation.
However, you might find it more convenient to do so. You
can find directions for removing door in Step 10.
Installation Preparation 2
• Examine dishwasher and locate connections. See Step 4.
• Locate dishwasher where there is easy access to drain,
water, and electrical lines. The best location is on either side
of the kitchen sink for access to existing plumbing and ease
in loading dishes. See Step 4.
• Electrical, water, and drain connections are not the same for
all age, brands, or models of dishwashers. Check the
location and length of home utilities. See Step 4.
• A 15-20 amp, grounded, 120 volt AC only, electrical supply is
required. See Steps 4 and 8.
• If dishwasher drain hose will be connected to a food
disposer for the first time, knock out plug located inside
disposer inlet. See Steps 4 and 6.
• Kinked water or drain hoses can cause problems. See Step
6.
• Dishwashers need to be connected to a hot water supply
with enough water pressure to insure an adequate fill.
See Steps 4 and 7.
• Each home installation differs. You will need additional
parts listed above to complete your installation.
See Steps 4 and 7.
• Flush water line prior to making the final connection to
prevent clogging of dishwasher’s filter screen. See Step 7.
• The dishwasher will look, sound, and perform best when
properly leveled. See Step 5. (NOTE: If levelers are
removed during installation, make sure the floor is flat and
free of any obstruction.)
• Anchor the dishwasher. See Step 9.
Kickplate Assembly
Figure 1
Bottom Screws
(Insulation available
some models)
Kickplate
Water Inlet
Valve
Entry Must be
Above Trap
Sink at Left
Sink at Right
“Y”
Branch
Tailpiece
2” Drain Hose Hole
Figure 5
Sink at Right
Remove
Knockout
Plug in
Disposer 2” Drain Hose Hole
Figure 7(b)
Parts You Will Need* (Not Included)
• Drain Hose Clamp, 11/4” Diameter
• Elbow, 90° with a 3/8” National Pipe Thread or 3/4” Hose Thread
Fitting
• Conduit Connector
• Wire Nuts, two (2) for 12-14 gauge wire
• Plumbers Tape
* If required: Available at:
• “Y” Branch Tailpiece and Plumbing Supply Store
Connector Kit (See Step 4)
• Air Gap Kit (See Step 4) Plumbing Supply Store
• Fasteners for floor Hardware Store
anchoring (See Step 9)
IMPORTANT: Disconnect power before starting installation.
Electrical
1. The dishwasher operates on a 120 volt, 60 Hz electrical supply.
Provide a separate circuit with a fuse or circuit breaker rated for
at least 15 amps (20 amps if connected with disposer) but not
more than 20 amps.
2. Note the locations of electrical supply and dishwasher’s
electrical junction box on right underside of unit behind kickplate
assembly. See Figure 3.
3. Cut access hole in shaded area shown in Figure 2.
4. Pull electrical cable through hole into installation area.
Water
1. Determine where you will connect to hot water supply. Review
Figure 3 and note the location of water inlet valve.
Property Damage
Do not use the furnished drain hose or a rubber garden hose
for the water supply line. Either of these hoses can burst.
Flooding may occur and cause property damage.
3. If you connect to a sink trap, local codes may require you to
install an air gap kit, (not included). The drain hose will be routed
from dishwasher to air gap inlet as shown in Figure 6. An air
gap kit is available from a plumbing supply store. NOTE: If the
drain hose is installed through the floor, an air
gap is necessary.
4. If you connect to a disposer, the large end of drain hose will
fit. Figure 7(a). The knock out plug must be removed from
inside disposer inlet before making the final fit to drain
hose. See Figure 7(b).
3
Roughing In
Electric Shock Hazard
Observe all local codes and ordinances for
electrical and plumbing connections. All electrical
and plumbing work should be performed by
qualified persons. Failure to follow this warning
could result in death or serious injury.
1. Make sure your location has the right drain, water, and electrical
outlets to make the connections. Do not install unit under a
cooktop range. Damage to plastic tub will occur.
90° 90°
21/ ”2
6”
24”
6”
21 / 2 ”
73/4”
Hot
Water
Line
Electrical
Wiring
▲▲
▲▲
▲
▲▲
▲▲▲
3”
4”
24”
min.
18”
Electrical, water,
and drain lines
must be confined
to shaded area.
Figure 2
Through
Cabinet
2. Be sure water inlet valve is protected from freezing. If valve
freezes and ruptures, flooding may occur.
3. Determine amount of tubing needed to connect hot water
supply to the unit’s water inlet valve. Copper tubing must have a
minimum
3/8” OD. High-pressure and high-temperature rated
plastic tubing with a minimum inner diameter of
1/4” may be
used. A shut-off valve installed outside dishwasher cabinet is
best. See Figure 4.
34
1
/4” min.
IMPORTANT: For proper operation and appearance of unit,
cabinet opening should have dimensions as shown in Figure 2.
If unit is to be placed in a corner, there must be at least a 2-inch
side clearance to open door.
2. Remove any carpet from area to provide motor clearance. Floor
should be flat and free of any obstruction.
IMPORTANT: Drain, water, and electrical lines should be
roughed-in before going any further.
Air Gap
Figure 6
INSTALLER: Leave Installation Instructions with owner.
OWNER: Read your dishwasher Use and Care Manual. It contains
important safety information for operating this appliance. It also has
many suggestions for getting the best results from your dishwasher.
Dishwasher
Installation
Instructions
Electric Shock Hazard
Disconnect electrical power at the fuse box or
circuit breaker box before beginning installation.
Failure to follow this warning could result in death
or serious injury.
Right Side
Installation
Cut for
5/8” connection.
Drain
Motor
End
Cut for 3/4” connection.
Figure 7(a)
Larger end
of hose
fits disposer
inlet fitting.
PN: 154427301/H
AW: 154427301/008
4/15
Printed in U.S.A.
Drain Air Gap
Sink at Left
Alternate
Drain
Through
Floor into
Separate
Trap
Drain Hose
Adjustable Toeplate
Cabinet Preparation:
As a precaution, it is recommended, but not required that the cabinets
enclosing all sides of the dishwasher (including the underside of the
countertop) be sealed with an oil based paint or moisture-proof
polyurethane to prevent possible steam/moisture damage. *DIMENSIONS DO NOT INCLUDE INSULATION
NOTE: Recommended to use Stainless Steel braded hose.
Drying Vent Hose (if equipped)
Care must be given during installation and removal of the dishwasher
to avoid disconnection of the vent hose that is attached to the top of
the dishwasher.
Drying Vent
Hose
1. Measure height of cabinet opening
from underside of countertop to floor.
Check chart for height opening and
suggested adjustment.
2. Move dishwasher to front of installation area.
3. Loosen the front and rear leveling legs by turning
counterclockwise. Refer to chart for number of turns. See
Figure 8. Front levelers should allow 1/4” below underside of
countertop.
5
Leveling Dishwasher
within Cabinets
Number of Turns to
Adjust Levelers
Height of
Cabinet Opening
Leg Leveler Adjustment Chart
341/8” (86.7cm)
345/16” (87.2cm)
0
2
6
9
For additional height add shims under levelers.
4. If levelers have to be removed, make sure floor is free of
obstructions.
5. Place dishwasher inside cabinet area so that it is centered in
opening. Use caution when moving dishwasher to prevent
damage to dishwasher, floor, and cabinets.
6. Remove lower rack to check that dishwasher is level from side
to side by placing a level on the bottom of the inner door. See
Figure 9a.
Figure 8
5/ ”32
Socket
Socket
Rear Leveler
Wrench
Front Leveler
Figure 10
7
Finishing the Water
Connection
Property Damage
Do not solder within 6” of the water inlet valve. Damage to
the plastic parts in the valve may occur.
Use care that no sealer, dirt, or other objects enter the valve.
Damage to the filter screen may occur.
Be sure the dishwasher is placed where the water inlet valve
will be kept from freezing. If the valve freezes, it may rupture
and flooding may occur.
Water Line
1. Flush water line before connecting it to water inlet valve to
prevent early clogging of filter screen. Place a bunched towel
over end of line to prevent splashing. Open water supply valve for
a few seconds and let water drain into a pan. Turn off water
supply at shut-off valve.
Through
Wall
Through
Cabinet
Figure 11
1. Remove junction box cover and pull house wiring into junction
box. See Figures 12 and 13.
2. Use a UL listed conduit connector,(not included), at box to
stabilize wiring.
IMPORTANT: Be sure electrical cable is not routed behind
dishwasher’s motor.
Electrical Supply
Conduit
Connector
(not included)
Ground Wire
Through
Wall
Through
Cabinet
Junction Box
(in place)
Through
Floor
Figure 12
Floor Anchoring
This procedure is difficult and should be used only if countertop
mounting brackets cannot be used.
1. Screw 1/4” lag screws, (not included), through holes provided in
frame rail. See Figure 15.
2. Use expansion fasteners if floor is concrete.
Before starting the dishwasher,
Figure 15
Use
1/4” Lag Screws
(not included)
10
Cut Hazard
Electric Shock Hazard
Disconnect electrical power at the fuse box
or circuit breaker box before beginning
installation.
Failure to follow this warning could result in
death or serious injury.
Metal color panels are sharp and should be
handled with care. Wear gloves to protect
hands.
Failure to follow this warning may result in
injury.
Removing & Replacing
Door
Side
View
Figure 16c
Console
Metal
Liner
Door
Checking the Installation 11
check these items:
Drain hose is assembled to drain pump.
All packing materials and consumer literature have been
removed from unit.
Dishwasher is level and securely fastened.
Open and close door to make sure it does not hit
surrounding cabinet or countertop.
Water and drain lines have no kinks.
Wiring connections to junction box are tight.
Water supply is turned on.
Joints are free of leaks.
34” (86.4cm)
341/2” (87.6cm)
The drain hose loop must be at least 32” high from the floor
to insure proper drainage.
3. Inside junction box, attach ground wire under head of grounding
screw and tighten. See Figure 13.
4. Connect incoming black lead to dishwasher’s black lead and
incoming white lead to dishwasher’s white lead with wire nuts or
other suitable connectors,(not included). Wire nuts should be
tight.
4. Place door where it will not get scratched or damaged while
completing installation.
5. When ready to replace door, fit the slots on each side of top
door edge over the tabs on the metal liner. Push on sides to
insure the door is flat. Push up from bottom until there is no gap
between door and console. See Figure 16c.
6. Unlatch door and open while supporting outer door on both sides
at bottom to keep in place. Align screw holes and replace
screws.
Appearance of console and door may
vary from your model.
Remove
knockout
plug in
disposer
Pump Motor
Clamp
Connector
Sink at Left
32”
1. Unlatch and open
door. Using a Phillips
head screw driver,
remove two (2) screws
from inner door. Save
screws to reassemble.
See Figure 16a.
2. Close and latch door
while holding both
sides.
3. Place one hand on
each side of door and
pull down at top
approximately
1/4”.
Pull entire door
assembly toward
6
Finishing the Drain
Connection
Electric Shock Hazard
Plumbing material and drain hose must not come
in contact with wiring or electrical components.
Failure to follow this warning could result in
personal injury from exposed wiring.
1. Pull out unit and check to see if drain hose is correctly attached
to the drain pump assembly. If drain hose is not attached to
drain pump, follow the instruction sheet (included with drain
hose) on how to correctly install the drain hose to the drain pump
assembly.
2. Move unit back in place while routing drain hose through access
hole. Use caution to prevent damage to the dishwasher, floor
and cabinets. IMPORTANT: Make sure there are no sharp
bends or kinks that might restrict drain flow.
3. Secure drain hose to sink drain, disposer, or separate trap with a
clamp. IMPORTANT: Be careful not to overtighten clamp or
you may damage end of hose. Do not connect hose to
horizontal pipe between sink drain and disposer.
4. Be sure unit does not rest on drain hose. It should be free of
electrical components and door springs. Do not cut corrugated
drain hose. Pull excess through cabinet and place under sink.
Make sure hose does not come in contact with any sharp edges.
See Figure 10.
Through
Floor
2. Route water line to water inlet valve as shown in Figure 11.
3. While firmly pulling water supply line into 90° elbow, tightly
connect water supply to water inlet valve. Supply line must be
free of kinks, scales, chips, and lubricants.
4. Turn on water supply and check for leaks.
5. If water inlet valve clogs, make sure water supply is off. If using
a 3/8” NPT valve,remove four (4) screws at inlet end of valve and
clean filter screen. If using 3/4” hose thread fitting simply clean
filter screen.
Finishing the Electrical
Connection 8
Electric Shock Hazard
Make sure electrical power has been disconnected at fuse box
or circuit breaker box.
The dishwasher must be connected to a grounded metal,
permanent wiring system. The equipment-grounding
conductor must be run with the circuit conductors and
connected to the appliance’s equipment grounding terminal or
lead. It is the consumer’s responsibility to contact a qualified
installer to make sure the electrical installation conforms with
the National Electrical Code and local codes and ordinances.
Do not connect the dishwasher to the power supply until the
appliance is permanently grounded.
All wiring connections must be enclosed in the junction box.
This unit has copper lead wires.
Joining aluminum building wire to stranded copper wire
should be done by a qualified electrician using materials
recognized by UL and local codes.
Do not use an extension cord. Such use can result in fire,
electrical shock, or other personal injury.
Failure to follow these instructions could result in death or
serious injury.
Figure 13
White Wire to
White Wire
(Neutral)
Black Wire to
Black Wire (Hot)
Junction
Box Cover
10
The dishwasher must be secured to keep it from tilting when door is
opened. Choose one of the methods described below to secure unit.
Countertop Anchoring
1. Install the Cabinet Seal Kit (Instructions included in Kit)
2. Replace Kickplate. See Figure 1
3. Adjust levelers (see Step 5) so mounting brackets touch
underside of countertop. IMPORTANT: Dishwasher must rest on
floor—do not hang from countertop. See Figure 14.
4. Tub needs to be even with the front of adjoining cabinets.
5. Screw mounting brackets firmly to countertop using screws
provided in literature packet.
6. Open and close dishwasher door slowly. If door hits mounting
brackets lower the dishwasher in front and rear.
Securing the Dishwasher 9
Use Phillips Head Screws
# 8 x 5/8” (included in the
literature packet).
Figure 14
To Remove and Replace Outer Door
Operate the machine through at
least one fill and pump-out,
checking the following items:
At first fill, make sure water completely covers filter surface.
(Motor pump sound may be heard before water enters unit).
At pump-out, make sure all water is pumped out.
Check water connections again for leaks.
Electric Shock Hazard
If all connections are correct, there are no leaks,
and unit runs properly, replace the kickplate
assembly before placing unit into operation.
Failure to follow this warning could result in
electric shock.
1. Refer to Step 10, numbers 5 and 6, for replacing outer door.
2. Adjust door springs to balance weight of door. A correct spring
setting allows door to remain horizontal in opened position, yet
will rise to close with slight lift of finger.
3. If necessary, increase tension by moving springs to a hole
toward rear of unit or decrease by moving them toward front.
4. Turn electrical supply on.
Replacing Door
7. Remove lower rack to check that dishwasher is level from front
to back by placing the level at the bottom of the tub at the lower
rack wheel support. See Figure 9b.
8. Adjust levelers up or down until dishwasher is level.
Figure 9bFigure 9a
Figure 16a
Figure 16b
Appearance of console and door may
vary from your model.
5. Replace junction box cover. See Figure 13.
Note: If mounting your dishwasher to the
countertop or to the floor is not a desirable option,
you can order the side mount kit, 154806601/02, by
contacting your dealer or parts supplier. This allows
you to install the dishwasher by securing it to the
cabinets or partitions on either side of the unit. The
kit utilizes the front frame of the dishwasher to
secure the unit to the cabinet or partitions.
5 / ”32
you to remove.
See Figure 16b.
Note: Open and close door to make sure it does not hit
surrounding cabinets or countertop.
15/ ”16

Product specificaties

Merk: Frigidaire
Categorie: Vaatwasser
Model: FGCD2444S

Heb je hulp nodig?

Als je hulp nodig hebt met Frigidaire FGCD2444S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Vaatwasser Frigidaire

Frigidaire

Frigidaire FDSP450LAF Handleiding

28 Augustus 2023
Frigidaire

Frigidaire FDSP4501AS Handleiding

28 Augustus 2023
Frigidaire

Frigidaire FDPH4316AW Handleiding

26 Juli 2023
Frigidaire

Frigidaire FDPH4316AB Handleiding

26 Juli 2023
Frigidaire

Frigidaire FDPH4316AS Handleiding

26 Juli 2023
Frigidaire

Frigidaire FDPH4316AD Handleiding

26 Juli 2023
Frigidaire

Frigidaire FDPC4314AS Handleiding

26 Juli 2023
Frigidaire

Frigidaire FDPC4314AB Handleiding

26 Juli 2023
Frigidaire

Frigidaire FDPH431LAF Handleiding

26 Juli 2023
Frigidaire

Frigidaire FDPC4314AW Handleiding

26 Juli 2023

Handleiding Vaatwasser

Nieuwste handleidingen voor Vaatwasser

Haier

Haier XF 6B2M3PX1 Handleiding

10 December 2024
Haier

Haier XF1C3TB1FW Handleiding

10 December 2024
Gorenje

Gorenje GV642D65 Handleiding

10 December 2024
Gorenje

Gorenje GV16D5 Handleiding

10 December 2024
Gorenje

Gorenje GV642C65 Handleiding

10 December 2024
Gorenje

Gorenje GV662A60 Handleiding

10 December 2024
Neff

Neff S853HKX20E Handleiding

10 December 2024
Neff

Neff S857YMX12E Handleiding

10 December 2024
Haier

Haier XS 6B0M3PDB Handleiding

10 December 2024
Haier

Haier SXI 6B0S3FSBV Handleiding

10 December 2024