FoodSaver GameSaver Pro Plus Handleiding

FoodSaver Vacuumverpakker GameSaver Pro Plus

Lees hieronder de 📖 handleiding in het Nederlandse voor FoodSaver GameSaver Pro Plus (4 pagina's) in de categorie Vacuumverpakker. Deze handleiding was nuttig voor 123 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Features

For important safety information and helpful tips, please refer to the FoodSaver ®Reference Guide

included with your appliance. Questions? Visit us at www.foodsaver.com or call 1-800-777-5452 (U.S.)

or 1-877-804-5383 (Canada). Get tips on vacuum packaging and order FoodSaver ®accessories.

Roll Storage

Compartment

Removable

Vacuum Channel

Rubber Gasket

Sliding Door to

Vacuum Channel

Sealing Strip

Features of Your GameSaver®Appliance

Tips

Additional Features & Tips

For more usage tips and safety information, please refer to the FoodSaver®Reference Guide or visit our website at www.foodsaver.com.

Tips on Sealing a Bag

Make sure you’ve placed the bag in the proper

place. When making a bag from a roll, make sure end

of cut piece is on Sealing Strip (N), not over rubber

gasket (L) or in Vacuum Channel (K).

Prevent moisture or liquid from being pulled

into the Vacuum Channel or trapped in the

seal. Either pre-freeze moist foods such as raw

meat for 1-2 hours before vacuum packaging, or

place a folded paper towel between food and end of

bag to absorb excess liquids. Be sure to leave at least

3 inches between paper towel and end of bag so that

bag seals properly with paper towel inside.

Make sure the Seal Control Switch (E) is set to

the appropriate position.

Make sure you give appliance time to cool

down. Wait at least 20 seconds between seals.

Under very heavy usage, appliance will shut off

automatically to prevent overheating. If it does, wait

20 minutes to allow appliance to cool off.

Tips on Removing Air from a Bag

Make sure you’ve placed the bag in the proper

place. When vacuum packaging make sure open end

of bag is inside Vacuum Channel (K). Also make sure

roll itself is tucked back into Roll Storage

Compartment (J) or it could prevent appliance from

operating properly.

Check for wrinkles in the bag along the Sealing

Strip. Wrinkles in seal may cause leakage and allow

air to come back into bag. Check for wrinkles in bag

along Sealing Strip (N) before closing lid and vacuum

packaging. If you find wrinkles after sealing bag,

simply cut bag open and vacuum package again.

If motor runs for more than 30 seconds with-

out stopping, you may need to adjust bag and try

again. If you are making initial seal on a piece of bag

material with two open ends, make sure bag is placed

on Sealing Strip, not in Vacuum Channel (K). If you

are vacuum packaging with a bag, make sure open

end is placed down inside Vacuum Channel and make

sure Accessory Hose (B) is not attached. If you are

vacuum packaging with an accessory, check Accessory

Hose in appliance lid and in accessory to ensure a

tight fit. Make sure Seal Control Switch (E) is set to

appropriate position.

General Tips

Tips for Successful Vacuum Packaging

(continued)

1. Vacuum packaging is NOT a substitute for the

heat process of canning. Perishables still need to

be refrigerated or frozen.

2. For best results, use FoodSaver®Bags, Canisters

and Accessories.

3. During the vacuum packaging process, small

amounts of liquids, crumbs or food particles can

be inadvertently pulled into Vacuum Channel (K),

clogging the pump and damaging your appliance.

To prevent this, follow these tips:

a. For moist and juicy foods such as raw meats:

Freeze first and avoid overfilling bags. You can

also place a folded paper towel inside top of bag,

but below seal area, before vacuum packaging.

b. For soups, sauces and liquids: Freeze first and

avoid overfilling bags. Or, use a canister in

refrigerator.

c. For powdery or fine-grained foods: Avoid

overfilling bags or use a canister. You can also

place a coffee filter or paper towel inside

before vacuum packaging.

d. If your appliance features a Removable

Vacuum Channel (K), empty and clean after

each use.

4. To avoid overfilling, always leave at least 3 inches

of bag material between bag contents and top of

bag. Then leave at least one additional inch of bag

material for each time you plan to reuse bag.

5. Do not create your own side seams for a

FoodSaver®Bag. These bags are manufactured

with a special side seam, which is sealed all the

way to the outer edge.

6. To prevent wrinkles in seal when vacuum

packaging bulky items, gently stretch bag flat

along Sealing Strip (N) before you close lid.

7. If you are unsure your bag was sealed properly,

simply reseal bag about 1⁄ 4 inch above first seal.

8. When you are vacuum packaging items with sharp

edges (dry spaghetti, silverware, etc.), protect

bag from punctures by wrapping item in soft

cushioning material, such as a paper towel. You

may want to use a canister or Mason jar instead

of a bag.

9. When using accessories, remember to leave one

inch of space at top of canister or container.

10. Pre-freeze fruits and blanch vegetables before

vacuum packaging for best results. See pages 2-3

of FoodSaver®Reference Guide for more

information.

First Printing: 03/07 Item # 9100060001017 (03/07)

QuickStart

GameSaver®Pro Plus

Accessory Hose Storage

Accessory Hose

Cancel Button

Instant Seal Button

Seal Control Switch

(5-Position)

Indicator Light

Pulse Button

Accessory Port

Bag Cutter

The Removable Vacuum Channel makes cleanup(K)

easy when small amounts of liquids are inadvertently

pulled into the Vacuum Channel during vacuum

process. (See FoodSaver®Reference Guide for tips on

preventing this.)

After each use, slide open side door (M) on right side

of appliance and pull Vacuum Channel out. Remove

rubber gasket (L) and wipe gasket with damp cloth.

Empty Vacuum Channel and wash in warm soapy

water or place on top rack of dishwasher. Dry

thoroughly before re-inserting into appliance.

Appliance cannot be used without Vacuum Channel

in place.

Removable Vacuum Channel

GS Pro.qxd:QS.1505_GSpro_v3.qxd 4/19/07 4:00 PM Page 5

And More

Bags & Rolls

Pulse Mode allows you maximum control over the

vacuum process for crushable items in bags. After

placing bag in Vacuum Channel (K) and closing lid,

follow these instructions:

1. Set Seal Control Switch (E) to Pulse Mode.

2. Press down firmly on lid to activate motor, then

release.

3. Press Pulse Button (G) and hold for as long as

desired, then release. Indicator Light (F) will flash

quickly after Pulse Button is used. To remove

more air, simply repeat Step 3.

4. After removing desired amount of air, press

Instant Seal Button (D) to seal bag. Indicator Light

will flash slowly when bag is sealing.

5. When motor and light turn off, vacuum process

is complete.

Tip: When using Pulse Mode, you MUST

MUST

MUST MUST press

Instant Seal Button to seal bag. If there is no activity

for 30 seconds, appliance will shut off automatically

and bag will not be sealed.

The Instant Seal Button (D) stops the vacuum

process early and seals the bag, preventing delicate

foods such as cookies from being crushed.

1. Vacuum package as described in previous sections.

2. To stop process before all air is removed, press and

release Instant Seal Button. Vacuum process will

stop within a few seconds and bag will be sealed.

3. When motor and Indicator Light (F) turn off,

open lid and remove bag.

The Instant Seal Button is also used to end Pulse

Mode (see instructions above).

If you want to seal a bag without vacuuming, use the

Seal Only position on the Seal Control Switch (E).

You can even reseal bags such as Mylar®potato chip

bags.

1. Place open end of bag on Sealing Strip (N) and

close lid.

2. Set Seal Control Switch to Seal Only.

3. Press down firmly on lid with both hands until

motor starts, then release. Motor and Indicator

Light (F) will turn on, indicating bag is sealing.

4. When motor and Indicator Light turn off, open lid

and remove bag.

Note: If Sealing Strip is too hot for a mylar bag, try

setting Seal Control Switch to instead of Seal

Only. As long as you place open end of bag on

Sealing Strip (not in Vacuum Channel), no air will be

removed.

Additional Features

Pulse Mode

Instant Seal

Seal Only

1. Place item(s) in bag, allowing at least 3 inches

of space between bag contents and top of bag.

2. Open appliance lid and place open end of bag

down into Vacuum Channel (K). Make sure roll

material is tucked backed into Roll Storage

Compartment (J) or it could prevent the

appliance from operating properly.

3. Close lid.

4. Set Seal Control Switch (E) to:

to vacuum package using FoodSaver®bags

(medium seal time).

to vacuum package moist and juicy foods

such as raw meat (longer seal time).

5. To begin vacuum process, press down firmly

on lid with both hands until motor starts, then

release. Motor will continue to run.

6. When motor and Indicator Light (F) turn off,

vacuum and seal process is complete. Open lid and

remove bag. Refrigerate or freeze if needed. (See

FoodSaver®Reference Guide for food safety tips.)

1. Open appliance lid and place roll into Roll Storage

Compartment (J).

2. Pull out enough bag material to hold item to be

vacuum packaged, plus at least 3 inches. Close lid.

3. Turn Seal Control Switch (E) to .Seal Only

4. Press down firmly on lid with both hands until

motor starts, then release lid. Motor and Indicator

Light (F) will turn on as bag material is sealing.

5. When motor and light turn off, cut bag material by

pressing down lightly on lid and sliding Bag Cutter

(I) from one end of sliding channel to other end.

6. Open lid, remove bag, and tuck roll back into Roll

Storage Compartment before vacuum packaging.

Now you are ready to vacuum package with your

new bag (see below).

Getting Started

Registering your appliance is quick and easy at www.foodsaver.com.

Accessories

FoodSaver®Accessory Guidelines

FoodSaver®Accessories

1. Always leave at least one inch of space between

contents and rim.

2. Wipe rim of canister, container or bottle to ensure

it is clean and dry.

3. Place lid on canister or container, or place stopper

in bottle.

4. For accessories with a large knob on lid, turn knob

to Vacuum. Vacuum package using instructions

below. When vacuum process is complete, turn

knob to Closed before removing Accessory Hose.

5. For accessories without a large knob on lid,

vacuum package using instructions below.

How to Open FoodSaver®Accessories after Vacuum Packaging

FoodSaver Vacuum Packaging Canisters

(without large knob on lid)

To release vacuum and open, push gray rubber

button on lid.

FoodSaver Bulk Canisters and Quick

Marinators (with large knob on lid) and

Universal Lids

To release vacuum and open, turn knob on lid

to Open.

FoodSaver Jar Sealer with Mason Jars

For use with Ball®and Kerr ® brand Mason jars.

IMPORTANT: Do NOT use screw bands when

vacuum packaging jars. To open, wedge spoon

between Mason jar lid and highest part of threaded

rim. Twist spoon gently to release vacuum.

FoodSaver Bottle Stoppers

To release vacuum and open, twist and pull up on

Bottle Stopper.

How to Vacuum Package with FoodSaver®Accessories

1. Prepare container according to FoodSaver®

Accessory Guidelines above.

2. Insert one end of Accessory Hose (B) into

Accessory Port (H) on appliance. Insert other

end into port on accessory. Twist tab on

Accessory Hose while inserting to ensure a tight fit.

3. Turn Seal Control Switch (E) to .

4. To begin vacuum process, press down firmly on

lid until motor starts, then release. Motor will

continue to run.

5. When motor and Indicator Light (F) turn off,

vacuum process is complete.

6. Gently twist and remove Accessory Hose from

accessory and appliance.

7. To test vacuum, simply tug on accessory lid. It

should not move.

Note: For important tips on using accessories

with different foods, please refer to the FoodSaver®

Reference Guide.

How to Make a Bag from a FoodSaver®Roll

How to Vacuum Package with FoodSaver®Bags

Pull Out Bag Material Set Seal Control Switch Press and Release Lid

Place Bag in Vacuum Channel Set Seal Control Switch Press and Release Lid

Insert Accessory Hose Set Seal Control Switch Press and Release Lid

GS Pro.qxd:QS.1505_GSpro_v3.qxd 4/19/07 4:00 PM Page 2

Product specificaties

Merk:	FoodSaver
Categorie:	Vacuumverpakker
Model:	GameSaver Pro Plus

Heb je hulp nodig?

Als je hulp nodig hebt met FoodSaver GameSaver Pro Plus stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Vacuumverpakker FoodSaver

FoodSaver FM2437 Handleiding

29 Augustus 2024

FoodSaver VS1200 Handleiding

29 Augustus 2024

FoodSaver FS2160 Handleiding

29 Augustus 2024

FoodSaver V1100 Handleiding

29 Augustus 2024

FoodSaver V1150 Handleiding

29 Augustus 2024

FoodSaver VS0100 Handleiding

29 Augustus 2024

FoodSaver FM2900 Handleiding

29 Augustus 2024

FoodSaver VS2150 Handleiding

29 Augustus 2024

FoodSaver FM1500 Handleiding

27 Augustus 2024

FoodSaver FM2435 Handleiding

26 Augustus 2024

Handleiding Vacuumverpakker

Nieuwste handleidingen voor Vacuumverpakker

Steinberg SBS-SEM-250 Handleiding

15 December 2024

Ambiano GT-FSH-01 Handleiding

11 December 2024

Adler AD 4514 Handleiding

9 December 2024

Adler AD 4515 Handleiding

9 December 2024

Solis Vac Wet & Dry 5708 Handleiding

4 December 2024

Clatronic PC-VK 1080 Handleiding

3 December 2024

Whirlpool W11 SVD140 Handleiding

3 December 2024

Magic Vac Axolute Handleiding

19 November 2024

Catler VS 8011 Handleiding

19 November 2024

Gastroback Design Pro 46011 Handleiding

19 November 2024