Focal FDP Sport Handleiding

Focal Hifi systeem FDP Sport

Lees hieronder de 📖 handleiding in het Nederlandse voor Focal FDP Sport (12 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 131 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
1
Shared Controls
(All Channels)
Ch 1+2 Controls Refer to Figures 2B, 3B, or 4B for wiring diagrams
Refer to Figures 2A, 3A, or 4A for control diagramsCh 3+4 Controls
Figure 1 | Navigating the FDP SPORT Controls
CONFIGURATIONS
There are the 3 basic configurations that you will be using when installing your Focal FDP SPORT.
Pick the mode you will be running, turn to the appropriate page, and follow the instructions to
make the correct amp adjustments.
4 Channel Stereo Mode (Page 2)
2 Channel Bridged Stereo Mode (Page 4)
3 Channel Stereo and Bridged Mono Mode (Page 6)
FDP SPORT: 4-CH MOTO & ALL-TERRAIN AMP
OPERATION / CONFIGURATION
2
4 CHANNEL STEREO MODE
INPUTS
Under the “INPUTS”, move the switch to either position of “2IN or 4IN” depending on how many
inputs you are using to run the amp, 2 or 4.
If you are only using one single pair of RCAs from your source, then plug them into the Channel 3+4
or (REAR) RCA inputs, and select “2IN”
If you are using the Harley Molex harness, then you are setting the switch to “2IN”
NOTE: If your factory Harley (2014 or newer models) came with working rear speakers, then the rear
outputs on the headunit will be active. In this case only, you will need to remove the small harness from
the end of the Harley input plug that plugs directly into the SPORT amp. This small adapter will be labeled
for further clarity. In this particular case, you will run the Input switch to “4IN”.
NORMAL/BRIDGED
This switch should be set to “NORM”
SLOPE
You can select the crossover slope you want for both channels, either a 6db/octave slope or a 12db/
octave slope.
12 db/octave is a sharper roll off slope, where the 6db/octave is more gradual roll off slope.
CHANNELS 1 & 2 CROSSOVER CONFIGURATION
Channels 1+2 can be run in either Full Range, or in High Pass (HP) mode, using the bottom
row of controls. To run in Full Range mode, adjust the HP control down to the 10hz position.
To run in HP mode, adjust the HP control to your desired HP frequency.
CHANNELS 3 & 4 CROSSOVER CONFIGURATION
You can select between Full Range (FR), Low Pass (LP), High Pass (HP), or Band Pass (BP) mode,
using the top row of controls.
For FR, set MODE switch to HP, and adjust the HP control down to 10hz.
For HP, set the MODE switch to HP, and adjust the HP control to set the HP frequency.
For LP, set the MODE switch to LP. Adjust the HP control down to 10hz. Then adjust LP control to set
the LP frequency.
For BP, set the MODE switch to LP, and adjust the LP control to the desired LP frequency. Adjust the
HP control to set HP frequency.
GAIN CONTROL
In this mode you will be using both gain controls to match your sources output level to your
amplifiers input.
SPEAKER OUTPUTS
Following the wiring diagram in Figure 2B, wire your speakers to the appropriate output wires,
respecting the channels, and the + and – phasing.


Product specificaties

Merk: Focal
Categorie: Hifi systeem
Model: FDP Sport

Heb je hulp nodig?

Als je hulp nodig hebt met Focal FDP Sport stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Hifi systeem Focal

Handleiding Hifi systeem

Nieuwste handleidingen voor Hifi systeem